Analysis of Broadband HIGP-Impedance Ground Plane Antenna Designs

This research ties together computational and experimental analysis of two types of high-impedance ground plane (HIGP) antennas. One type of antenna consists of a proposed two-layer design. The structure consists of a bowtie antenna mounted over the surface of a HIGR The proposed structure was intended to achieve a resonant frequency of 3 GHz and a bandwidth of 48%; however, a design error results in a significant mismatch in operating bands between the antenna and HIGR Experiment results indicate the structure performs poorly across the entire measured band of 2-5 GHz. A new two-layer design is developed and presented. The new design takes advantage of lessons learned such as designing around material properties of readily available materials. Analysis of integrated, or one-layer, HIGP antennas are also presented. The one- layer versions utilize the exact same design parameters as their corresponding two-layer designs; the bowtie radiating element is simply positioned in the plane rather than over, the HIGR Results indicate the design error in the proposed two-layer structure affects the performance of the one-layer version less than the two-layer antenna. A comparison between the original and new integrated HIGP antennas show an improvement in input impedance, but a decrease in bandwidth

Advanced Design Methodologies and Novel Applications of Reflectarray Antennas

Reflectarray antennas combine the numerous advantages of printed antenna arrays and reflector antennas and create a hybrid high-gain antenna with a low-profile, low-mass, and diversified radiation performance. Reflectarrays are now emerging as the new generation of high-gain antennas for long-distance communications. In this dissertation, some advanced concepts demonstrating novel features of reflectarray antennas are presented. • First, various approaches for radiation analysis of reflectarray antennas are described and implemented. Numerical results are then presented for a variety of systems and the advantages, limitations, and accuracy of these approaches are discussed and compared with each other. • A broadband technique by using sub-wavelength elements is proposed and prototypes are fabricated and tested. This technique enables the reflectarray to achieve a significant bandwidth improvement with no additional cost. • Infrared reflectarrays antennas are studied for possible applications in concentrating solar power systems. Material losses, an important design issue at infrared frequencies, are investigated and reflectarrays consisted of dielectric resonant elements are proposed with low-loss features at infrared. • Multi-beam reflectarray antennas are studied and it is demonstrated that by optimizing the phase of the elements, a desirable multi-beam performance can be achieved using a single-feed. Local and global phase-only optimization techniques have been implemented. Two Ka-band quad-beam prototypes with symmetric and asymmetric beams have been fabricated and tested. • Different approaches for beam-scanning with reflectarray antennas are also revieand it is shown that for moderately wide angle beam-scanning, utilizing a feed displacement technique is more suitable than an aperture phase tuning approach. A feed displacement beam-scanning design with novel aperture phase distribution is proposed for the reflectarray antenna, and is further optimized to improve the performance. A high-gain Ka-band prototype achieving 60 degrees scan range with side-lobe levels below 15 dB is demonstrated. • The feasibility of designing reflectarray antennas on conformal surfaces is also studied numerically. A generalized analysis approach is presented and the radiation performance of reflectarray antennas on singly-curved conformal cylindrical platforms are studied and compared with their planar counterpart. It is revealed that conformal reflectarray antennas are a suitable choice for a high-gain antenna where curved platforms are required. In summary, different challenges in reflectarray analysis and design are addressed in this dissertation. On the element design challenges, bandwidth improvement and infrared operation of reflectarray antennas have been studied. On the system level challenges, multi-beam designs, beam-scanning performance, and conformal platforms have been investigated. Several prototypes have been fabricated and tested, demonstrating the novel features and potential applications of reflectarray antennas

Radio frequency and capacitive sensors for dielectric characterization of low-conductivity media

Low-conductivity media are found in a vast number of applications, for example as electrical insulation or as the matrix polymer in high strength-to-weight ratio structural composites. In some applications, these materials are subjected to extreme environmental, thermal, and mechanical conditions that can affect the material\u27s desired performance. In a more general sense, a medium may be comprised of one or more layers with unknown material properties that may affect the desired performance of the entire structure. It is often, therefore, of great import to be able to characterize the material properties of these media for the purpose of estimating their future performance in a certain application. Low-conductivity media, or dielectrics, are poor electrical conductors and permit electromagnetic waves and static electric fields to pass through with minimal attenuation. The amount of electrical energy that may be stored (and lost) in these fields depends directly upon the material property, permittivity, which is generally complex, frequency-dependent and has a measurable effect on sensors designed to characterize dielectric media. In this work, two different types of dielectric sensors: radio frequency resonant antennas and lower-frequency (\u3c1 MHz) capacitive sensors, are designed for permittivity characterization in their respective frequency regimes. In the first part of this work, the capability of characterizing multilayer dielectric structures is studied using a patch antenna, a type of antenna that is primarily designed for data communications in the microwave bands but has application in the field of nondestructive evaluation as well. Each configuration of a patch antenna has a single lowest resonant (dominant mode) frequency that is dependent upon the antenna\u27s substrate material and geometry as well as the permittivity and geometry of exterior materials. Here, an extant forward model is validated using well-characterized microwave samples and a new method of resonant frequency and quality factor determination from measured data is presented. Excellent agreement between calculated and measured values of sensor resonant frequency was obtained for the samples studied. Agreement between calculated and measured quality factor was good in some cases but incurred the particular challenge of accurately quantifying multiple contributions to loss from the sensor structure itself, which at times dominates the contribution due to the sample material. Two later chapters describe the development of capacitive sensors to quantify the low-frequency changes in material permittivity due to environmental aging mechanisms. One embodiment involves the application of coplanar concentric interdigital electrode sensors for the purpose of investigating polymer-matrix degradation in glass-fiber composites due to isothermal aging. Samples of bismaleimide-matrix glass-fiber composites were aged at several high temperatures to induce thermal degradation and capacitive sensors were used to measure the sensor capacitance and dissipation factor, parameters that are directly proportional to the real and imaginary components of complex permittivity, respectively. It was shown that real permittivity and dissipation factor decreased with increasing aging temperature, a trend that was common to both interdigital sensor measurements and standard parallel plate electrode measurements. The second piece of work involves the development of cylindrical interdigital electrode sensors to characterize complex permittivity changes in wire insulation due to aging-related degradation. The sensor was proven effective in detecting changes in irradiated nuclear power plant wiring insulation and in aircraft wiring insulation due to liquid chemical immersion. In all three cases, the results indicate a clear correlation of measured capacitance and dissipation factor with increased degradation

Wearable antennas: design, connectivity and evaluation measurement techniques

Wearable antennas and electronics technology rapidly grows the last decades and leads to a future where smart textiles will be integrated into our garments. However the wearable technology research includes unsolved or of different approach challenges. This thesis deals with challenges regarding wearable antenna characterization and measurements, textile antennas feeding and textile transmission lines interconnecting. Regarding the wearable antenna characterization and measurements, a novel design of a liquid torso phantom and a new methodology for evaluating wearable antenna performance by using the cylindrical near field measurement technique are proposed. As for the textile antennas and transmission lines feeding and interconnecting, two novel methods are proposed

High Temperature Materials Characterization And Sensor Application

This dissertation presents new solutions for turbine engines in need of wireless temperature sensors at temperatures up to 1300oC. Two important goals have been achieved in this dissertation. First, a novel method for precisely characterizing the dielectric properties of high temperature ceramic materials at high temperatures is presented for microwave frequencies. This technique is based on a high-quality (Q)-factor dielectrically-loaded cavity resonator, which allows for accurate characterization of both dielectric constant and loss tangent of the material. The dielectric properties of Silicon Carbonitride (SiCN) and Silicoboron Carbonitride (SiBCN) ceramics, developed at UCF Advanced Materials Processing and Analysis Center (AMPC) are characterized from 25 to 1300oC. It is observed that the dielectric constant and loss tangent of SiCN and SiBCN materials increase monotonously with temperature. This temperature dependency provides the valuable basis for development of wireless passive temperature sensors for high-temperature applications. Second, wireless temperature sensors are designed based on the aforementioned hightemperature ceramic materials. The dielectric constant of high-temperature ceramics increases monotonically with temperature and as a result changes the resonant frequency of the resonator. Therefore, the temperature can be extracted by measuring the change of the resonant frequency of the resonator. In order for the resonator to operate wirelessly, antennas need to be included in the design. Three different types of sensors, corresponding to different antenna configurations, are designed and the prototypes are fabricated and tested. All of the sensors successfully perform at temperatures over 1000oC. These wireless passive sensor designs will significantly benefit turbine engines in need of sensors operating at harsh environment

Antennas and Propagation

This Special Issue gathers topics of utmost interest in the field of antennas and propagation, such as: new directions and challenges in antenna design and propagation; innovative antenna technologies for space applications; metamaterial, metasurface and other periodic structures; antennas for 5G; electromagnetic field measurements and remote sensing applications