Step-Up Converter Interfaces for Magnetron Power Supply

Fine particulate matter like carbon soot harms the respiratory system. One approach to reducing soot pollution is microwave-assisted soot oxidation. The magnetron, which generates microwave energy requires a high-voltage gain converter. In this thesis, a DC/DC converter is proposed to supply the two voltages required by a magnetron by utilizing dual resonant circuit modules. By combining the switches of the step-up resonant stage with a bridgeless power factor correction (PFC) stage, an AC/DC topology is proposed. The proposed AC/DC topology allows for a high power factor (PF) and reduced input conduction losses. The converter utilizes a parallel CL resonant circuit with voltage doubler output to achieve a high-voltage gain, and an LLC resonant circuit to provide the step-down. The circuit is then verified through PSIM with a peak of 1.8kW. A proof-of-concept hardware test with AC input testing step-up 822V and step-down 1.3V outputs simultaneously with a 0.96PF is performed

A three-switch high-voltage converter

A novel single active switch two-diodes high-voltage converter is presented. This converter can operate into a capacitor-diode voltage multiplier, which offers simpler structure and control, higher efficiency, reduced electromagnetic interference (EMI), and size and weight savings compared with traditional switched-mode regulated voltage multipliers. Two significant advantages are the continuous input current and easy isolation extension. The new converter is experimentally verified. Both the steady-state and dynamic theoretical models are correlated well with the experimental dat

Integrated fuzzy and phase shift controller for output step voltage control in multilevel inverter with reduced switch count

A modified multilevel inverter with a configurable level generation is proposed in this paper. The MLI is composed of a modified boost converter at the front end followed by a level generation circuit and a H-bridge configuration. The front-end converter is biased with a PV source with a Hybrid boost resonant converter. The switches are triggered out of phase through a MPP tracker which uses Fractional INC MPPT. The secondary side of the circuit is composed of a derived voltage doubler along with the voltage regulator. The output of the doubler is regulated through a level converter which integrates a fuzzy controller and a phase shift controller. The modified multilevel inverter uses a low-voltage PV source as input and generates a variable-step multilevel output voltage with lower harmonic distortion and it is suitable for low-power PV applications

Piezoelectric Transformer Integration Possibility in High Power Density Applications

The contents of this work investigate the capability of integrating the PT in applications by invoking the ratio of the throughput power to volume represented by the term: power density. The fundamentals of the PT are introduced in chapter two. In chapter three, the fundamental limitations of the PT's capability of transferring power to the load are studied. There are three major limitations: temperature rise due to losses during operation, electromechanical limits of material, and interactions with output rectifier. The analysis and estimation are then verified by experiments and calculations implemented on three different PT samples fabricated from three different manufacturers. The subject of chapter four is the behavior of the PT's power amplifier. This chapter concentrates on two main amplifier topologies, optimized based on the simplicity of structure and minimization of components (passive and active): class D and class E amplifiers. The operational characteristics of these amplifiers with the PT are then comparison. Methods to track the optimum frequency and discontinuous working mode of the PT are proposed as the approaches to improve the energy transfer of the PT. In chapter five, prototypes of four devices using a PT are developed and introduced as illustrations of the integration of PTs into practical applications: an igniter for high intensity discharge (HID) lamps, high DC voltage power supplies, and electronic ballasts for LEDs, and stand-alone ionizers for food sterilizers. Some concluding statements and ideas for future works are located in the last chapter - chapter six

Soft-Switched Step-Up Medium Voltage Power Converters

With a ten-year average annual growth rate of 19 percent, wind energy has been the largest source of new electricity generation for the past decade. Typically, an offshore wind farm has a medium voltage ac (MVac) grid that collects power from individual wind turbines. Since the output voltage of a wind turbine is too low (i.e., typically 400 690 V) to be connected to the MVac grid (i.e., 20 40 kV), a heavy line-frequency transformer is used to step up the individual turbines output voltage to the MV level. To eliminate the need for bulky MVac transformers, researchers are gravitating towards the idea of replacing the MVac grid with a medium voltage dc (MVdc) grid, so that MV step-up transformers are replaced by MV step-up power electronic converters that operate at the medium frequency range with much lower size and weight. This dissertation proposes a class of modular step-up transformerless MV SiC-based power converters with soft-switching capability for wind energy conversion systems with MVdc grid. This dissertation consists of two parts: the first part focuses on the development of two novel groups of step-up isolated dc-dc MV converters that utilize various step-up resonant circuits and soft-switched high voltage gain rectifier modules. An integrated magnetic design approach is also presented to combine several magnetic components together in the modular high voltage gain rectifiers. The second part of this dissertation focuses on the development of several three-phase ac-dc step-up converters with integrated active power factor correction. In particular, a bridgeless input ac-dc rectifier is also proposed to combine with the devised step-up transformerless dc-dc converters (presented in the first part) to form the three-phase soft-switched ac-dc step-up voltage conversion unit. In each of the presented modular step-up converter configurations, variable frequency control is used to regulate the output dc voltage of each converter module. The operating principles and characteristics of each presented converter are provided in detail. The feasibility and performance of all the power converter concepts presented in this dissertation are verified through simulation results on megawatts (MW) design examples, as well as experimental results on SiC-based laboratory-scale proof-of-concept prototypes

Soft-Switched Step-Up Medium Voltage Power Converters

With a ten-year average annual growth rate of 19 percent, wind energy has been the largest source of new electricity generation for the past decade. Typically, an offshore wind farm has a medium voltage ac (MVac) grid that collects power from individual wind turbines. Since the output voltage of a wind turbine is too low (i.e., typically 400 690 V) to be connected to the MVac grid (i.e., 20 40 kV), a heavy line-frequency transformer is used to step up the individual turbines output voltage to the MV level. To eliminate the need for bulky MVac transformers, researchers are gravitating towards the idea of replacing the MVac grid with a medium voltage dc (MVdc) grid, so that MV step-up transformers are replaced by MV step-up power electronic converters that operate at the medium frequency range with much lower size and weight. This dissertation proposes a class of modular step-up transformerless MV SiC-based power converters with soft-switching capability for wind energy conversion systems with MVdc grid. This dissertation consists of two parts: the first part focuses on the development of two novel groups of step-up isolated dc-dc MV converters that utilize various step-up resonant circuits and soft-switched high voltage gain rectifier modules. An integrated magnetic design approach is also presented to combine several magnetic components together in the modular high voltage gain rectifiers. The second part of this dissertation focuses on the development of several three-phase ac-dc step-up converters with integrated active power factor correction. In particular, a bridgeless input ac-dc rectifier is also proposed to combine with the devised step-up transformerless dc-dc converters (presented in the first part) to form the three-phase soft-switched ac-dc step-up voltage conversion unit. In each of the presented modular step-up converter configurations, variable frequency control is used to regulate the output dc voltage of each converter module. The operating principles and characteristics of each presented converter are provided in detail. The feasibility and performance of all the power converter concepts presented in this dissertation are verified through simulation results on megawatts (MW) design examples, as well as experimental results on SiC-based laboratory-scale proof-of-concept prototypes

Soft-Switched Step-Up Medium Voltage Power Converters

With a ten-year average annual growth rate of 19 percent, wind energy has been the largest source of new electricity generation for the past decade. Typically, an offshore wind farm has a medium voltage ac (MVac) grid that collects power from individual wind turbines. Since the output voltage of a wind turbine is too low (i.e., typically 400 690 V) to be connected to the MVac grid (i.e., 20 40 kV), a heavy line-frequency transformer is used to step up the individual turbines output voltage to the MV level. To eliminate the need for bulky MVac transformers, researchers are gravitating towards the idea of replacing the MVac grid with a medium voltage dc (MVdc) grid, so that MV step-up transformers are replaced by MV step-up power electronic converters that operate at the medium frequency range with much lower size and weight. This dissertation proposes a class of modular step-up transformerless MV SiC-based power converters with soft-switching capability for wind energy conversion systems with MVdc grid. This dissertation consists of two parts: the first part focuses on the development of two novel groups of step-up isolated dc-dc MV converters that utilize various step-up resonant circuits and soft-switched high voltage gain rectifier modules. An integrated magnetic design approach is also presented to combine several magnetic components together in the modular high voltage gain rectifiers. The second part of this dissertation focuses on the development of several three-phase ac-dc step-up converters with integrated active power factor correction. In particular, a bridgeless input ac-dc rectifier is also proposed to combine with the devised step-up transformerless dc-dc converters (presented in the first part) to form the three-phase soft-switched ac-dc step-up voltage conversion unit. In each of the presented modular step-up converter configurations, variable frequency control is used to regulate the output dc voltage of each converter module. The operating principles and characteristics of each presented converter are provided in detail. The feasibility and performance of all the power converter concepts presented in this dissertation are verified through simulation results on megawatts (MW) design examples, as well as experimental results on SiC-based laboratory-scale proof-of-concept prototypes

Morphing Switched-Capacitor Converters with Variable Conversion Ratio

High-voltage-gain and wide-input-range dc-dc converters are widely used in various electronics and industrial products such as portable devices, telecommunication, automotive, and aerospace systems. The two-stage converter is a widely adopted architecture for such applications, and it is proven to have a higher efficiency as compared with that of the single-stage converter. This paper presents a modular-cell-based morphing switched-capacitor (SC) converter for application as a front-end converter of the two-stage converter. The conversion ratio of this converter is flexible and variable and can be freely extended by increasing more SC modules. The varying conversion ratio is achieved through the morphing of the converter's structure corresponding to the amplitude of the input voltage. This converter is light and compact, and is highly efficient over a very wide range of input voltage and load conditions. Experimental work on a 25-W, 6-30-V input, 3.5-8.5-V output prototype, is performed. For a single SC module, the efficiency over the entire input voltage range is higher than 98%. Applied into the two-stage converter, the overall efficiency achievable over the entire operating range is 80% including the driver's loss