837 research outputs found
Equalization-Based Digital Background Calibration Technique for Pipelined ADCs
In this paper, we present a digital background calibration technique for pipelined analog-to-digital converters (ADCs). In this scheme, the capacitor mismatch, residue gain error, and amplifier nonlinearity are measured and then corrected in digital domain. It is based on the error estimation with nonprecision calibration signals in foreground mode, and an adaptive linear prediction structure is used to convert the foreground scheme to the background one. The proposed foreground technique utilizes the LMS algorithm to estimate the error coefficients without needing high-accuracy calibration signals. Several simulation results in the context of a 12-b 100-MS/s pipelined ADC are provided to verify the usefulness of the proposed calibration technique. Circuit-level simulation results show that the ADC achieves 28-dB signal-to-noise and distortion ratio and 41-dB spurious-free dynamic range improvement, respectively, compared with the noncalibrated ADC
Recommended from our members
Noise shaping Asynchronous SAR ADC based time to digital converter
Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin
Recommended from our members
Designs and calibration of delay-line based ADCs
Delay line ADCs become more and more attractive with technology scaling to smaller dimensions with lower voltages. Time domain resolution can be increased by high speed delay cells. A GHz sampling rate can be easily achieved with low power. However, linearity, which has always been an issue, becomes a problem with longer delay lines. Resolutions of reported delay-line ADCs are hardly more than 4 bits with sampling rates of hundreds of MHz. Thus, this dissertation addresses the linearity issue of delay line ADCs.
First, a novel 11-bit hybrid ADC using flash and delay line architectures, where a 4-bit flash ADC is followed by a 7-bit delay-line ADC, is proposed. In this structure, the noise/error of the second stage delay-line ADC is attenuated at the hybrid ADC output, such that the overall performance would not be limited by the poor linearity of the delay-line ADC. The achieved figure of merit (FOM) of 33.8 fJ/conversion-step is competitive with state-of-the-art ADCs. Furthermore, the proposed ADC inherits accuracy and high speed from the flash ADC and the delay-line ADC, respectively. The inherited advantages strongly support the scalability of the proposed ADC to provide a better performance with low power in further scaled fabrication processes.
Second, in order to remove the harmonic distortion of delay-line ADC, we present a technique which extends harmonic distortion correction (HDC) to digitally calibrate a delay-line ADC. In our simulation
results, digital calibration improves SNDR from 25.6 dB to 42.5 dB by averaging sample points, which corresponds to a 0.86 second calibration time.
Last, a multiple-pass delay line ADC is proposed to improve overall ADC performance in terms of speed and resolution. In this structure, a multiple-pass delay cell can be early triggered by the previous cell to increase speed. Also, phase interpolation is used to improve the effective number of bits. The design is designed and simulated in a commercial 40nm process technology. With 500MHz sampling rate, the multiple-pass delay line ADC achieves an SNDR of 37 dB and consumes 4.2 mW, which is competitive with other reported ADCs.Electrical and Computer Engineerin
Recommended from our members
Design Techniques for High-Performance SAR A/D Converters
The design of electronics needs to account for the non-ideal characteristics of the device technologies used to realize practical circuits. This is particularly important in mixed analog-digital design since the best device technologies are very different for digital compared to analog circuits. One solution for this problem is to use a calibration correction approach to remove the errors introduced by devices, but this adds complexity and power dissipation, as well as reducing operation speed, and so must be optimised. This thesis addresses such an approach to improve the performance of certain types of analog-to-digital converter (ADC) used in advanced telecommunications, where speed, accuracy and power dissipation currently limit applications. The thesis specifically focuses on the design of compensation circuits for use in successive approximation register (SAR) ADCs.
ADCs are crucial building blocks in communication systems, in general, and for mobile networks, in particular. The recently launched fifth generation of mobile networks (5G) has required new ADC circuit techniques to meet the higher speed and lower power dissipation requirements for 5G technology. The SAR has become one of the most favoured architectures for designing high-performance ADCs, but the successive nature of the circuit operation makes it difficult to reach ∼GS/s sampling rates at reasonable power consumption.
Here, two calibration techniques for high-performance SAR ADCs are presented. The first uses an on-chip stochastic-based mismatch calibration technique that is able to accurately compute and compensate for the mismatch of a capacitive DAC in a SAR ADC. The stochastic nature of the proposed calibration method enables determination of the mismatch of the CAPDAC with a resolution much better than that of the DAC. This allows the unit capacitor to scale down to as low as 280aF for a 9-bit DAC. Since the CAP-DAC causes a large part of the overall dynamic power consumption and directly determines both the sizes of the driving and sampling switches and the size of the input capacitive load of the ADC and the kT/C noise power, a small CAP-DAC helps the power efficiency. To validate the proposed calibration idea, a 10-bit asynchronous SAR ADC was fabricated in 28-nm CMOS. Measurement results show that the proposed stochastic calibration improves the ADC’s SFDR and SNDR by 14.9 dB, 11.5 dB, respectively. After calibration, the fabricated SAR ADC achieves an ENOB of 9.14 bit at a sampling rate of 85 MS/s, resulting in a Walden FoM of 10.9 fJ/c-s.
The second calibration technique is a timing-skew calibration for a time-interleaved (TI) SAR ADC that calibrates/computes the inter-channel timing and offset mismatch simultaneously. Simulation results show the effectiveness of this calibration method. When used together, the proposed mismatch calibration technique and the timing-skew
calibration technique enables a TI SAR ADC to be designed that can achieve a sampling rate of ∼GS/s with 10-bit resolution and a power consumption as low as ∼10mW; specifications that satisfy the requirements of 5G technology
Digital Background Self-Calibration Technique for Compensating Transition Offsets in Reference-less Flash ADCs
This Dissertation focusses on proving that background calibration using adaptive algorithms are low-cost, stable and effective methods for obtaining high accuracy in flash A/D converters. An integrated reference-less 3-bit flash ADC circuit has been successfully designed and taped out in UMC 180 nm CMOS technology in order to prove the efficiency of our proposed background calibration. References for ADC transitions have been virtually implemented built-in in the comparators dynamic-latch topology by a controlled mismatch added to each comparator input front-end. An external very simple DAC block (calibration bank) allows control the quantity of mismatch added in each comparator front-end and, therefore, compensate the offset of its effective transition with respect to the nominal value. In order to assist to the estimation of the offset of the prototype comparators, an auxiliary A/D converter with higher resolution and lower conversion speed than the flash ADC is used: a 6-bit capacitive-DAC SAR type. Special care in synchronization of analogue sampling instant in both ADCs has been taken into account.
In this thesis, a criterion to identify the optimum parameters of the flash ADC design with adaptive background calibration has been set. With this criterion, the best choice for dynamic latch architecture, calibration bank resolution and flash ADC resolution are selected.
The performance of the calibration algorithm have been tested, providing great programmability to the digital processor that implements the algorithm, allowing to choose the algorithm limits, accuracy and quantization errors in the arithmetic. Further, systematic controlled offset can be forced in the comparators of the flash ADC in order to have a more exhaustive test of calibration
High-Speed Analog-to-Digital Converters for Broadband Applications
Flash Analog-to-Digital Converters (ADCs), targeting optical
communication standards, have been reported in SiGe BiCMOS
technology. CMOS implementation of such designs faces two
challenges. The first is to achieve a high sampling speed, given the
lower gain-bandwidth (lower ft) of CMOS technology. The second
challenge is to handle the wide bandwidth of the input signal with a
certain accuracy. Although the first problem can be relaxed by using
the time-interleaved architecture, the second problem remains as a
main obstacle to CMOS implementation. As a result, the feasibility
of the CMOS implementation of ADCs for such applications, or other
wide band applications, depends primarily on achieving a very small
input capacitance (large bandwidth) at the
desired accuracy.
In the flash architecture, the input capacitance is traded off for
the achievable accuracy. This tradeoff becomes tighter with
technology scaling. An effective way to ease this tradeoff is to use
resistive offset averaging. This permits the use of smaller area
transistors, leading to a reduction in the ADC input capacitance. In
addition, interpolation can be used to decrease the input
capacitance of flash ADCs. In an interpolating architecture, the
number of ADC input preamplifiers is reduced significantly, and a
resistor network interpolates
the missing zero-crossings needed for an N-bit conversion. The resistive network also averages
out the preamplifiers offsets. Consequently, an interpolating network works also as an averaging network.
The resistor network used for averaging or interpolation causes a
systematic non-linearity at the ADC transfer characteristics edges.
The common solution to this problem is to extend the preamplifiers
array beyond the input signal voltage range by using dummy
preamplifiers. However, this demands a corresponding extension of
the flash ADC reference-voltage resistor ladder. Since the voltage
headroom of the reference ladder is considered to be a main
bottleneck in the implementation of flash ADCs in deep-submicron
technologies with reduced supply voltage, extending the reference
voltage beyond the input voltage range is highly undesirable.
The principal objective of this thesis is to develop a new circuit
technique to enhance the bandwidth-accuracy product of flash ADCs.
Thus, first, a rigorous analysis of flash ADC architectures accuracy-bandwidth tradeoff is presented.
It is demonstrated that the interpolating architecture achieves a superior accuracy compared
to that of a full flash architecture for the same input capacitance, and hence would lead to
a higher bandwidth-accuracy product, especially in deep-submicron technologies that use low power supplies. Also, the
gain obtained, when interpolation is employed, is quantified. In addition, the limitations of a previous
claim, which suggests that an interpolating architecture is equivalent to an averaging
full flash architecture that trades off accuracy for the input capacitance, is presented. Secondly, a termination
technique for the averaging/interpolation network of flash ADC preamplifiers is devised. The proposed technique maintains the linearity of the ADC at the transfer
characteristics edges and cancels out the over-range voltage, consumed by the dummy preamplifiers. This makes flash ADCs more amenable for integration in deep-submicron CMOS technologies. In addition, the
elimination of this over-range voltage allows a larger
least-significant bit. As a result, a higher input referred offset
is tolerated, and a significant reductions in the ADC input
capacitance and
power dissipation are achieved at the same accuracy. Unlike a previous solution, the proposed
technique does not introduce negative transconductance at flash ADC preamplifiers array edges.
As a result, the offset averaging technique can be used efficiently.
To prove the resulting saving in the ADC input capacitance and power
dissipation that is attained by the proposed termination technique,
a 6-bit 1.6-GS/s flash ADC test chip is designed and implemented in
0.13-m CMOS technology. The ADC consumes 180 mW from a 1.5-V
supply and achieves a Signal-to-Noise-plus-Distortion Ratio (SNDR)
of 34.5 dB and 30 dB at 50-MHz and 1450-MHz input signal frequency,
respectively. The measured peak Integral-Non-Linearity (INL) and
Differential-Non-Linearity (DNL) are 0.42 LSB and 0.49 LSB,
respectively
Frequency and fundamental signal measurement algorithms for distributed control and protection applications
Increasing penetration of distributed generation within electricity networks leads to the requirement for cheap, integrated, protection and control systems. To minimise cost, algorithms for the measurement of AC voltage and current waveforms can be implemented on a single microcontroller, which also carries out other protection and control tasks, including communication and data logging. This limits the frame rate of the major algorithms, although analogue to digital converters (ADCs) can be oversampled using peripheral control processors on suitable microcontrollers. Measurement algorithms also have to be tolerant of poor power quality, which may arise within grid-connected or islanded (e.g. emergency, battlefield or marine) power system scenarios. This study presents a 'Clarke-FLL hybrid' architecture, which combines a three-phase Clarke transformation measurement with a frequency-locked loop (FLL). This hybrid contains suitable algorithms for the measurement of frequency, amplitude and phase within dynamic three-phase AC power systems. The Clarke-FLL hybrid is shown to be robust and accurate, with harmonic content up to and above 28% total harmonic distortion (THD), and with the major algorithms executing at only 500 samples per second. This is achieved by careful optimisation and cascaded use of exact-time averaging techniques, which prove to be useful at all stages of the measurements: from DC bias removal through low-sample-rate Fourier analysis to sub-harmonic ripple removal. Platform-independent algorithms for three-phase nodal power flow analysis are benchmarked on three processors, including the Infineon TC1796 microcontroller, on which only 10% of the 2000 mus frame time is required, leaving the remainder free for other algorithms
Aika-digitaalimuunnin laajakaistaisiin aikapohjaisiin analogia-digitaalimuuntimiin
Modern deeply scaled semiconductor processes make the design of voltage-domain circuits increasingly challenging. On the contrary, the area and power consumption of digital circuits are improving with every new process node. Consequently, digital solutions are designed in place of their purely analog counterparts in applications such as analog-to-digital (A/D) conversion. Time-based analog-to-digital converters (ADC) employ digital-intensive architectures by processing analog quantities in time-domain. The quantization step of the time-based A/D-conversion is carried out by a time-to-digital converter (TDC).
A free-running ring oscillator -based TDC design is presented for use in wideband time-based ADCs. The proposed architecture aims to maximize time resolution and full-scale range, and to achieve error resilient conversion performance with minimized power and area consumptions. The time resolution is maximized by employing a high-frequency multipath ring oscillator, and the full-scale range is extended using a high-speed gray counter. The error resilience is achieved by custom sense-amplifier -based sampling flip-flops, gray coded counter and a digital error correction algorithm for counter sampling error correction. The implemented design achieves up to 9-bit effective resolution at 250 MS/s with 4.3 milliwatt power consumption.Modernien puolijohdeteknologioiden skaalautumisen seurauksena jännitetason piirien suunnittelu tulee entistä haasteellisemmaksi. Toisaalta digitaalisten piirirakenteiden pinta-ala sekä tehonkulutus pienenevät prosessikehityksen myötä. Tästä syystä digitaalisia ratkaisuja suunnitellaan vastaavien puhtaasti analogisien rakenteiden tilalle. Analogia-digitaalimuunnos (A/D-muunnos) voidaan toteuttaa jännitetason sijaan aikatasossa käyttämällä aikapohjaisia A/D-muuntimia, jotka ovat rakenteeltaan pääosin digitaalisia. Kvantisointivaihe aikapohjaisessa A/D-muuntimessa toteutetaan aika-digitaalimuuntimella.
Työ esittelee vapaasti oskilloivaan silmukkaoskillaattoriin perustuvan aika-digitaalimuuntimen, joka on suunniteltu käytettäväksi laajakaistaisessa aikapohjaisessa A/D-muuntimessa. Esitelty rakenne pyrkii maksimoimaan muuntimen aikaresoluution sekä muunnosalueen, sekä saavuttamaan virhesietoisen muunnostoiminnan minimoidulla tehon sekä pinta-alan kulutuksella. Aikaresoluutio on maksimoitu hyödyntämällä suuritaajuista monipolkuista silmukkaoskillaattoria, ja muunnosalue on maksimoitu nopealla Gray-koodi -laskuripiirillä. Muunnosprosessin virhesietoisuus on saavutettu toteuttamalla näytteistys herkillä kiikkuelementeillä, hyödyntämällä Gray-koodattua laskuria, sekä jälkiprosessoimalla laskurin näytteistetyt arvot virheenkorjausalgoritmilla. Esitelty muunnintoteutus saavuttaa 9 bitin efektiivisen resoluution 250 MS/s näytetaajuudella ja 4.3 milliwatin tehonkulutuksella
Time-based, Low-power, Low-offset 5-bit 1 GS/s Flash ADC Design in 65nm CMOS Technology
Low-power, medium resolution, high-speed analog-to-digital converters (ADCs) have always been important block which have abundant applications such as digital signal processors (DSP), imaging sensors, environmental and biomedical monitoring devices. This study presents a low power Flash ADC designed in nanometer complementary metal-oxide semiconductors (CMOS) technology. Time analysis on the output delay of the comparators helps to generate one more bit. The proposed technique reduced the power consumption and chip area substantially in comparison to the previous state-of-the-art work. The proposed ADC was developed in TSMC 65nm CMOS technology. The offset cancellation technique was embedded in the proposed comparator to decrement the static offset of the comparator. Moreover, one more bit was generated without using extra comparators. The proposed ADC achieved 4.1 bits ENOB at input Nyquist frequency. The simulated differential and integral non-linearity static tests were equal to +0.26/-0.17 and +0.22/-0.15, respectively. The ADC consumed 7.7 mW at 1 GHz sampling frequency, achieving 415 fJ/Convstep Figure of Merit (FoM)
- …