67,036 research outputs found
Autocalibration with the Minimum Number of Cameras with Known Pixel Shape
In 3D reconstruction, the recovery of the calibration parameters of the
cameras is paramount since it provides metric information about the observed
scene, e.g., measures of angles and ratios of distances. Autocalibration
enables the estimation of the camera parameters without using a calibration
device, but by enforcing simple constraints on the camera parameters. In the
absence of information about the internal camera parameters such as the focal
length and the principal point, the knowledge of the camera pixel shape is
usually the only available constraint. Given a projective reconstruction of a
rigid scene, we address the problem of the autocalibration of a minimal set of
cameras with known pixel shape and otherwise arbitrarily varying intrinsic and
extrinsic parameters. We propose an algorithm that only requires 5 cameras (the
theoretical minimum), thus halving the number of cameras required by previous
algorithms based on the same constraint. To this purpose, we introduce as our
basic geometric tool the six-line conic variety (SLCV), consisting in the set
of planes intersecting six given lines of 3D space in points of a conic. We
show that the set of solutions of the Euclidean upgrading problem for three
cameras with known pixel shape can be parameterized in a computationally
efficient way. This parameterization is then used to solve autocalibration from
five or more cameras, reducing the three-dimensional search space to a
two-dimensional one. We provide experiments with real images showing the good
performance of the technique.Comment: 19 pages, 14 figures, 7 tables, J. Math. Imaging Vi
3D Visual Perception for Self-Driving Cars using a Multi-Camera System: Calibration, Mapping, Localization, and Obstacle Detection
Cameras are a crucial exteroceptive sensor for self-driving cars as they are
low-cost and small, provide appearance information about the environment, and
work in various weather conditions. They can be used for multiple purposes such
as visual navigation and obstacle detection. We can use a surround multi-camera
system to cover the full 360-degree field-of-view around the car. In this way,
we avoid blind spots which can otherwise lead to accidents. To minimize the
number of cameras needed for surround perception, we utilize fisheye cameras.
Consequently, standard vision pipelines for 3D mapping, visual localization,
obstacle detection, etc. need to be adapted to take full advantage of the
availability of multiple cameras rather than treat each camera individually. In
addition, processing of fisheye images has to be supported. In this paper, we
describe the camera calibration and subsequent processing pipeline for
multi-fisheye-camera systems developed as part of the V-Charge project. This
project seeks to enable automated valet parking for self-driving cars. Our
pipeline is able to precisely calibrate multi-camera systems, build sparse 3D
maps for visual navigation, visually localize the car with respect to these
maps, generate accurate dense maps, as well as detect obstacles based on
real-time depth map extraction
Self-correction of 3D reconstruction from multi-view stereo images
We present a self-correction approach to improving the
3D reconstruction of a multi-view 3D photogrammetry system.
The self-correction approach has been able to repair
the reconstructed 3D surface damaged by depth discontinuities.
Due to self-occlusion, multi-view range images
have to be acquired and integrated into a watertight nonredundant
mesh model in order to cover the extended surface
of an imaged object. The integrated surface often suffers
from “dent” artifacts produced by depth discontinuities
in the multi-view range images. In this paper we propose
a novel approach to correcting the 3D integrated surface
such that the dent artifacts can be repaired automatically.
We show examples of 3D reconstruction to demonstrate the
improvement that can be achieved by the self-correction
approach. This self-correction approach can be extended
to integrate range images obtained from alternative range
capture devices
Efficient generic calibration method for general cameras with single centre of projection
Generic camera calibration is a non-parametric calibration technique that is applicable to any type of vision sensor. However, the standard generic calibration method was developed with the goal of generality and it is therefore sub-optimal for the common case of cameras with a single centre of projection (e.g. pinhole, fisheye, hyperboloidal catadioptric). This paper proposes novel improvements to the standard generic calibration method for central cameras that reduce its complexity, and improve its accuracy and robustness. Improvements are achieved by taking advantage of the geometric constraints resulting from a single centre of projection. Input data for the algorithm is acquired using active grids, the performance of which is characterised. A new linear estimation stage to the generic algorithm is proposed incorporating classical pinhole calibration techniques, and it is shown to be significantly more accurate than the linear estimation stage of the standard method. A linear method for pose estimation is also proposed and evaluated against the existing polynomial method. Distortion correction and motion reconstruction experiments are conducted with real data for a hyperboloidal catadioptric sensor for both the standard and proposed methods. Results show the accuracy and robustness of the proposed method to be superior to those of the standard method
New instruments and technologies for Cultural Heritage survey: full integration between point clouds and digital photogrammetry
In the last years the Geomatic Research Group of the Politecnico di Torino faced some new research topics about new instruments for point cloud generation (e.g. Time of Flight cameras) and strong integration between multi-image matching techniques and 3D Point Cloud information in order to solve the ambiguities of the already known matching algorithms. ToF cameras can be a good low cost alternative to LiDAR instruments for the generation of precise and accurate point clouds: up to now the application range is still limited but in a near future they will be able to satisfy the most part of the Cultural Heritage metric survey requirements. On the other hand multi-image matching techniques with a correct and deep integration of the point cloud information can give the correct solution for an "intelligent" survey of the geometric object break-lines, which are the correct starting point for a complete survey. These two research topics are strictly connected to a modern Cultural Heritage 3D survey approach. In this paper after a short analysis of the achieved results, an alternative possible scenario for the development of the metric survey approach inside the wider topic of Cultural Heritage Documentation is reporte
Extrinisic Calibration of a Camera-Arm System Through Rotation Identification
Determining extrinsic calibration parameters is a necessity in any robotic
system composed of actuators and cameras. Once a system is outside the lab
environment, parameters must be determined without relying on outside artifacts
such as calibration targets. We propose a method that relies on structured
motion of an observed arm to recover extrinsic calibration parameters. Our
method combines known arm kinematics with observations of conics in the image
plane to calculate maximum-likelihood estimates for calibration extrinsics.
This method is validated in simulation and tested against a real-world model,
yielding results consistent with ruler-based estimates. Our method shows
promise for estimating the pose of a camera relative to an articulated arm's
end effector without requiring tedious measurements or external artifacts.
Index Terms: robotics, hand-eye problem, self-calibration, structure from
motio
- …