924 research outputs found
Sub-Nanosecond Time of Flight on Commercial Wi-Fi Cards
Time-of-flight, i.e., the time incurred by a signal to travel from
transmitter to receiver, is perhaps the most intuitive way to measure distances
using wireless signals. It is used in major positioning systems such as GPS,
RADAR, and SONAR. However, attempts at using time-of-flight for indoor
localization have failed to deliver acceptable accuracy due to fundamental
limitations in measuring time on Wi-Fi and other RF consumer technologies.
While the research community has developed alternatives for RF-based indoor
localization that do not require time-of-flight, those approaches have their
own limitations that hamper their use in practice. In particular, many existing
approaches need receivers with large antenna arrays while commercial Wi-Fi
nodes have two or three antennas. Other systems require fingerprinting the
environment to create signal maps. More fundamentally, none of these methods
support indoor positioning between a pair of Wi-Fi devices
without~third~party~support.
In this paper, we present a set of algorithms that measure the time-of-flight
to sub-nanosecond accuracy on commercial Wi-Fi cards. We implement these
algorithms and demonstrate a system that achieves accurate device-to-device
localization, i.e. enables a pair of Wi-Fi devices to locate each other without
any support from the infrastructure, not even the location of the access
points.Comment: 14 page
AoA-aware Probabilistic Indoor Location Fingerprinting using Channel State Information
With expeditious development of wireless communications, location
fingerprinting (LF) has nurtured considerable indoor location based services
(ILBSs) in the field of Internet of Things (IoT). For most pattern-matching
based LF solutions, previous works either appeal to the simple received signal
strength (RSS), which suffers from dramatic performance degradation due to
sophisticated environmental dynamics, or rely on the fine-grained physical
layer channel state information (CSI), whose intricate structure leads to an
increased computational complexity. Meanwhile, the harsh indoor environment can
also breed similar radio signatures among certain predefined reference points
(RPs), which may be randomly distributed in the area of interest, thus mightily
tampering the location mapping accuracy. To work out these dilemmas, during the
offline site survey, we first adopt autoregressive (AR) modeling entropy of CSI
amplitude as location fingerprint, which shares the structural simplicity of
RSS while reserving the most location-specific statistical channel information.
Moreover, an additional angle of arrival (AoA) fingerprint can be accurately
retrieved from CSI phase through an enhanced subspace based algorithm, which
serves to further eliminate the error-prone RP candidates. In the online phase,
by exploiting both CSI amplitude and phase information, a novel bivariate
kernel regression scheme is proposed to precisely infer the target's location.
Results from extensive indoor experiments validate the superior localization
performance of our proposed system over previous approaches
Efficient AoA-based wireless indoor localization for hospital outpatients using mobile devices
The motivation of this work is to help outpatients find their corresponding departments or clinics, thus, it needs to provide indoor positioning services with a room-level accuracy. Unlike wireless outdoor localization that is dominated by the global positioning system (GPS), wireless indoor localization is still an open issue. Many different schemes are being developed to meet the increasing demand for indoor localization services. In this paper, we investigated the AoA-based wireless indoor localization for outpatients’ wayfinding in a hospital, where Wi-Fi access points (APs) are deployed, in line, on the ceiling. The target position can be determined by a mobile device, like a smartphone, through an efficient geometric calculation with two known APs coordinates and the angles of the incident radios. All possible positions in which the target may appear have been comprehensively investigated, and the corresponding solutions were proven to be the same. Experimental results show that localization error was less than 2.5 m, about 80% of the time, which can satisfy the outpatients’ requirements for wayfinding
Higher order feature extraction and selection for robust human gesture recognition using CSI of COTS Wi-Fi devices
Device-free human gesture recognition (HGR) using commercial o the shelf (COTS) Wi-Fi
devices has gained attention with recent advances in wireless technology. HGR recognizes the human
activity performed, by capturing the reflections ofWi-Fi signals from moving humans and storing
them as raw channel state information (CSI) traces. Existing work on HGR applies noise reduction
and transformation to pre-process the raw CSI traces. However, these methods fail to capture
the non-Gaussian information in the raw CSI data due to its limitation to deal with linear signal
representation alone. The proposed higher order statistics-based recognition (HOS-Re) model extracts
higher order statistical (HOS) features from raw CSI traces and selects a robust feature subset for the
recognition task. HOS-Re addresses the limitations in the existing methods, by extracting third order
cumulant features that maximizes the recognition accuracy. Subsequently, feature selection methods
derived from information theory construct a robust and highly informative feature subset, fed as
input to the multilevel support vector machine (SVM) classifier in order to measure the performance.
The proposed methodology is validated using a public database SignFi, consisting of 276 gestures
with 8280 gesture instances, out of which 5520 are from the laboratory and 2760 from the home
environment using a 10 5 cross-validation. HOS-Re achieved an average recognition accuracy of
97.84%, 98.26% and 96.34% for the lab, home and lab + home environment respectively. The average
recognition accuracy for 150 sign gestures with 7500 instances, collected from five di erent users was
96.23% in the laboratory environment.Taylor's University through its TAYLOR'S PhD SCHOLARSHIP Programmeinfo:eu-repo/semantics/publishedVersio
Wi-Fi For Indoor Device Free Passive Localization (DfPL): An Overview
The world is moving towards an interconnected and intercommunicable network of animate and inanimate objects with the emergence of Internet of Things (IoT) concept which is expected to have 50 billion connected devices by 2020. The wireless communication enabled devices play a major role in the realization of IoT. In Malaysia, home and business Internet Service Providers (ISP) bundle Wi-Fi modems working in 2.4 GHz Industrial, Scientific and Medical (ISM) radio band with their internet services. This makes Wi-Fi the most eligible protocol to serve as a local as well as internet data link for the IoT devices. Besides serving as a data link, human entity presence and location information in a multipath rich indoor environment can be harvested by monitoring and processing the changes in the Wi-Fi Radio Frequency (RF) signals. This paper comprehensively discusses the initiation and evolution of Wi-Fi based Indoor Device free Passive Localization (DfPL) since the concept was first introduced by Youssef et al. in 2007. Alongside the overview, future directions of DfPL in line with ongoing evolution of Wi-Fi based IoT devices are briefly discussed in this paper
- …