Self-Calibrated, Low-Jitter and Low-Reference-Spur Injection-Locked Clock Multipliers

Department of Electrical EngineeringThis dissertation focuses primarily on the design of calibrators for the injection-locked clock multiplier (ILCM). ILCMs have advantage to achieve an excellent jitter performance at low cost, in terms of area and power consumption. The wide loop bandwidth (BW) of the injection technique could reject the noise of voltage-controlled oscillator (VCO), making it thus suitable for the rejection of poor noise of a ring-VCO and a high frequency LC-VCO. However, it is difficult to use without calibrators because of its sensitiveness in process-voltage-temperature (PVT) variations. In Chapter 2, conventional frequency calibrators are introduced and discussed. This dissertation introduces two types of calibrators for low-power high-frequency LC-VCO-based ILFMs in Chapter 3 and Chapter 4 and high-performance ring-VCO-based ILCM in Chapter 5. First, Chapter 3 presents a low power and compact area LC-tank-based frequency multiplier. In the proposed architecture, the input signals have a pulsed waveform that involves many high-order harmonics. Using an LC-tank that amplifies only the target harmonic component, while suppressing others, the output signal at the target frequency can be obtained. Since the core current flows for a very short duration, due to the pulsed input signals, the average power consumption can be dramatically reduced. Effective removal of spurious tones due to the damping of the signal is achieved using a limiting amplifier. In this work, a prototype frequency tripler using the proposed architecture was designed in a 65 nm CMOS process. The power consumption was 950 ??W, and the active area was 0.08 mm2. At a 3.12 GHz frequency, the phase noise degradation with respect to the theoretical bound was less than 0.5 dB. Second, Chapter 4 presents an ultra-low-phase-noise ILFM for millimeter wave (mm-wave) fifth-generation (5G) transceivers. Using an ultra-low-power frequency-tracking loop (FTL), the proposed ILFM is able to correct the frequency drifts of the quadrature voltage-controlled oscillator of the ILFM in a real-time fashion. Since the FTL is monitoring the averages of phase deviations rather than detecting or sampling the instantaneous values, it requires only 600??W to continue to calibrate the ILFM that generates an mm-wave signal with an output frequency from 27 to 30 GHz. The proposed ILFM was fabricated in a 65-nm CMOS process. The 10-MHz phase noise of the 29.25-GHz output signal was ???129.7 dBc/Hz, and its variations across temperatures and supply voltages were less than 2 dB. The integrated phase noise from 1 kHz to 100 MHz and the rms jitter were???39.1 dBc and 86 fs, respectively. Third, Chapter 5 presents a low-jitter, low-reference-spur ring voltage-controlled oscillator (ring VCO)-based ILCM. Since the proposed triple-point frequency/phase/slope calibrator (TP-FPSC) can accurately remove the three root causes of the frequency errors of ILCMs (i.e., frequency drift, phase offset, and slope modulation), the ILCM of this work is able to achieve a low-level reference spur. In addition, the calibrating loop for the frequency drift of the TP-FPSC offers an additional suppression to the in-band phase noise of the output signal. This capability of the TP-FPSC and the naturally wide bandwidth of the injection-locking mechanism allows the ILCM to achieve a very low RMS jitter. The ILCM was fabricated in a 65-nm CMOS technology. The measured reference spur and RMS jitter were ???72 dBc and 140 fs, respectively, both of which are the best among the state-of-the-art ILCMs. The active silicon area was 0.055 mm2, and the power consumption was 11.0 mW.clos

CMOS Signal Synthesizers for Emerging RF-to-Optical Applications

The need for clean and powerful signal generation is ubiquitous, with applications spanning the spectrum from RF to mm-Wave, to into and beyond the terahertz-gap. RF applications including mobile telephony and microprocessors have effectively harnessed mixed-signal integration in CMOS to realize robust on-chip signal sources calibrated against adverse ambient conditions. Combined with low cost and high yield, the CMOS component of hand-held devices costs a few cents per part per million parts. This low cost, and integrated digital processing, make CMOS an attractive option for applications like high-resolution imaging and ranging, and the emerging 5-G communication space. RADAR techniques when expanded to optical frequencies can enable micrometers of resolution for 3D imaging. These applications, however, impose upto 100x more exacting specifications on power and spectral purity at much higher frequencies than conventional RF synthesizers. This generation of applications will present unconventional challenges for transistor technologies - whether it is to squeeze performance in the conventionally used spectrum, already wrung dry, or signal generation and system design in the relatively emptier mm-Wave to sub-mmWave spectrum, much of the latter falling in the ``Terahertz Gap". Indeed, transistor scaling and innovative device physics leading to new transistor topologies have yielded higher cut-off frequencies in CMOS, though still lagging well behind SiGe and III-V semiconductors. To avoid multimodule solutions with functionality partitioned across different technologies, CMOS must be pushed out of its comfort zone, and technology scaling has to have accompanying breakthroughs in design approaches not only at the system but also at the block level. In this thesis, while not targeting a specific application, we seek to formulate the obstacles in synthesizing high frequency, high power and low noise signals in CMOS and construct a coherent design methodology to address them. Based on this, three novel prototypes to overcome the limiting factors in each case are presented. The first half of this thesis deals with high frequency signal synthesis and power generation in CMOS. Outside the range of frequencies where the transistor has gain, frequency generation necessitates harmonic extraction either as harmonic oscillators or as frequency multipliers. We augment the traditional maximum oscillation frequency metric (fmax), which only accounts for transistor losses, with passive component loss to derive an effective fmax metric. We then present a methodology for building oscillators at this fmax, the Maximum Gain Ring Oscillator. Next, we explore generating large signals beyond fmax through harmonic extraction in multipliers. Applying concepts of waveform shaping, we demonstrate a Power Mixer that engineers transistor nonlinearity by manipulating the amplitudes and relative phase shifts of different device nodes to maximize performance at a specific harmonic beyond device cut-off. The second half proposes a new architecture for an ultra-low noise phase-locked loop (PLL), the Reference-Sampling PLL. In conventional PLLs, a noisy buffer converts the slow, low-noise sine-wave reference signal to a jittery square-wave clock against which the phase of a noisy voltage-controlled oscillator (VCO) is corrected. We eliminate this reference buffer, and measure phase error by sampling the reference sine-wave with the 50x faster VCO waveform already available on chip, and selecting the relevant sample with voltage proportional to phase error. By avoiding the N-squared multiplication of the high-power reference buffer noise, and directly using voltage-mode phase error to control the VCO, we eliminate several noisy components in the controlling loop for ultra-low integrated jitter for a given power consumption. Further, isolation of the VCO tank from any varying load, unlike other contemporary divider-less PLL architectures, results in an architecture with record performance in the low-noise and low-spur space. We conclude with work that brings together concepts developed for clean, high-power signal generation towards a hybrid CMOS-Optical approach to Frequency-Modulated Continuous-Wave (FMCW) Light-Detection-And-Ranging (LIDAR). Cost-effective tunable lasers are temperature-sensitive and have nonlinear tuning profiles, rendering precise frequency modulations or 'chirps' untenable. Locking them to an electronic reference through an electro-optic PLL, and electronically calibrating the control signal for nonlinearity and ambient sensitivity, can make such chirps possible. Approaches that build on the body of advances in electrical PLLs to control the performance, and ease the specification on the design of optical systems are proposed. Eventually, we seek to leverage the twin advantages of silicon-intensive integration and low-cost high-yield towards developing a single-chip solution that uses on-chip signal processing and phased arrays to generate precise and robust chirps for an electronically-steerable fine LIDAR beam

Special Topics in Information Technology

This open access book presents thirteen outstanding doctoral dissertations in Information Technology from the Department of Electronics, Information and Bioengineering, Politecnico di Milano, Italy. Information Technology has always been highly interdisciplinary, as many aspects have to be considered in IT systems. The doctoral studies program in IT at Politecnico di Milano emphasizes this interdisciplinary nature, which is becoming more and more important in recent technological advances, in collaborative projects, and in the education of young researchers. Accordingly, the focus of advanced research is on pursuing a rigorous approach to specific research topics starting from a broad background in various areas of Information Technology, especially Computer Science and Engineering, Electronics, Systems and Control, and Telecommunications. Each year, more than 50 PhDs graduate from the program. This book gathers the outcomes of the thirteen best theses defended in 2019-20 and selected for the IT PhD Award. Each of the authors provides a chapter summarizing his/her findings, including an introduction, description of methods, main achievements and future work on the topic. Hence, the book provides a cutting-edge overview of the latest research trends in Information Technology at Politecnico di Milano, presented in an easy-to-read format that will also appeal to non-specialists