Design Techniques for High Performance Serial Link Transceivers

Increasing data rates over electrical channels with significant frequency-dependent loss is difficult due to excessive inter-symbol interference (ISI). In order to achieve sufficient link margins at high rates, I/O system designers implement equalization in the transmitters and are motivated to consider more spectrally-efficient modulation formats relative to the common PAM-2 scheme, such as PAM-4 and duobinary. The first work, reviews when to consider PAM-4 and duobinary formats, as the modulation scheme which yields the highest system margins at a given data rate is a function of the channel loss profile, and presents a 20Gb/s triple-mode transmitter capable of efficiently implementing these three modulation schemes and three-tap feedforward equalization. A statistical link modeling tool, which models ISI, crosstalk, random noise, and timing jitter, is developed to compare the three common modulation formats operating on electrical backplane channel models. In order to improve duobinary modulation efficiency, a low-power quarter-rate duobinary precoder circuit is proposed which provides significant timing margin improvement relative to full-rate precoders. Also as serial I/O data rates scale above 10 Gb/s, crosstalk between neighboring channels degrades system bit-error rate (BER) performance. The next work presents receive-side circuitry which merges the cancellation of both near-end and far-end crosstalk (NEXT/FEXT) and can automatically adapt to different channel environments and variations in process, voltage, and temperature. NEXT cancellation is realized with a novel 3-tap FIR filter which combines two traditional FIR filter taps and a continuous-time band-pass filter IIR tap for efficient crosstalk cancellation, with all filter tap coefficients automatically determined via an ondie sign-sign least-mean-square (SS-LMS) adaptation engine. FEXT cancellation is realized by coupling the aggressor signal through a differentiator circuit whose gain is automatically adjusted with a power-detection-based adaptation loop. In conclusion, the proposed architectures in the transmitter side and receiver side together are to be good solution in the high speed I/O serial links to improve the performance by overcome the physical channel loss and adjacent channel noise as the system becomes complicated

Design of High-Speed SerDes Transceiver for Chip-to-Chip Communications in CMOS Process

With the continuous increase of on-chip computation capacities and exponential growth of data-intensive applications, the high-speed data transmission through serial links has become the backbone for modern communication systems. To satisfy the massive data-exchanging requirement, the data rate of such serial links has been updated from several Gb/s to tens of Gb/s. Currently, the commercial standards such as Ethernet 400GbE, InfiniBand high data rate (HDR), and common electrical interface (CEI)-56G has been developing towards 40+ Gb/s. As the core component within these links, the transceiver chipset plays a fundamental role in balancing the operation speed, power consumption, area occupation, and operation range. Meanwhile, the CMOS process has become the dominant technology in modern transceiver chip fabrications due to its large-scale digital integration capability and aggressive pricing advantage. This research aims to explore advanced techniques that are capable of exploiting the maximum operation speed of the CMOS process, and hence provides potential solutions for 40+ Gb/s CMOS transceiver designs. The major contributions are summarized as follows. A low jitter ring-oscillator-based injection-locked clock multiplier (RILCM) with a hybrid frequency tracking loop that consists of a traditional phase-locked loop (PLL), a timing-adjusted loop, and a loop selection state-machine is implemented in 65-nm C-MOS process. In the ring voltage-controlled oscillator, a full-swing pseudo-differential delay cell is proposed to lower the device noise to phase noise conversion. To obtain high operation speed and high detection accuracy, a compact timing-adjusted phase detector tightly combined with a well-matched charge pump is designed. Meanwhile, a lock-loss detection and lock recovery is devised to endow the RILCM with a similar lock-acquisition ability as conventional PLL, thus excluding the initial frequency set- I up aid and preventing the potential lock-loss risk. The experimental results show that the figure-of-merit of the designed RILCM reaches -247.3 dB, which is better than previous RILCMs and even comparable to the large-area LC-ILCMs. The transmitter (TX) and receiver (RX) chips are separately designed and fab- ricated in 65-nm CMOS process. The transmitter chip employs a quarter-rate multi-multiplexer (MUX)-based 4-tap feed-forward equalizer (FFE) to pre-distort the output. To increase the maximum operating speed, a bandwidth-enhanced 4:1 MUX with the capability of eliminating charge-sharing effect is proposed. To produce the quarter-rate parallel data streams with appropriate delays, a compact latch array associated with an interleaved-retiming technique is designed. The receiver chip employs a two-stage continuous-time linear equalizer (CTLE) as the analog front-end and integrates an improved clock data recovery to extract the sampling clocks and retime the incoming data. To automatically balance the jitter tracking and jitter suppression, passive low-pass filters with adaptively-adjusted bandwidth are introduced into the data-sampling path. To optimize the linearity of the phase interpolation, a time-averaging-based compensating phase interpolator is proposed. For equalization, a combined TX-FFE and RX-CTLE is applied to compensate for the channel loss, where a low-cost edge-data correlation-based sign zero-forcing adaptation algorithm is proposed to automatically adjust the TX-FFE’s tap weights. Measurement results show that the fabricated transmitter/receiver chipset can deliver 40 Gb/s random data at a bit error rate of 16 dB loss at the half-baud frequency, while consuming a total power of 370 mW

Fast data acquisition for silicon tracking detectors at high rates

Silicon tracking detectors play a key role in many current high energy physics experiments. To enhance experimental sensitivities for searches for new physics, beam energies and event rates are constantly being increased, which leads to growing volumes of detector data that have to be processed. This thesis covers high-speed data acquisition for silicon tracking detectors in the context of the Mu3e experiment and future hadron collider experiments. For the Mu3e experiment, a vertical slice of the trigger-less readout system is realized as a beam telescope consisting of 8 layers of pixel sensors that are read out using a prototype of the Mu3e front-end board. The performance of the full readout system is studied during beam tests. Sensor hit rates of up to 5 MHz can be handled without significant losses. Hence, the system fulfils the requirements for the first phase of the experiment. To fully exploit the potential of silicon tracking detectors at future hadron collider experiments, the implementation of high-speed data links is mandatory. Wireless links operating at frequencies of 60 GHz and above present an attractive alternative to electrical and optical links, as they offer high bandwidth, small form factor and low power consumption. This thesis describes readout concepts for tracking detectors applying wireless data transfer and presents studies of wireless data transmission