A Study on Buffer Distribution for RRAM-based FPGA Routing Structures

Compared to Application-Specific Integrated Circuits (ASICs), Field Programmable Gate Arrays (FPGAs) provide reconfigurablity at the cost of lower performance and higher power consumption. Exploiting a large number of programmable switches, routing structures are mainly responsible for the performance limitation. Hence, employing more efficient switches can drastically improve the performance and reduce the power consumption of the FPGA. Resistive Random Access Memory (RRAM)-based switches are one of the most promising candidates to improve the FPGA routing architecture thanks to their low on-resistance and non-volatility. The lower RC delay of RRAM-based routing multiplexers, as compared to CMOS-based routing structures encourages us to reconsider the buffer distribution in FPGAs. This paper proposes an approach to reduce the number of buffers in the routing path of RRAM-based FPGAs. Our architectural simulations show that the use of RRAM switches improves the critical path delay by 56% as compared to CMOS switches in standard FPGA circuits at 45-nm technology node while, at the same time, the area and power are reduced, respectively, by 17% and 9%. By adapting the buffering scheme, an extra bonus of 9% for delay reduction, 5% for power reduction and 16% for area reduction can be obtained, as compared to the conventional buffering approach for RRAM-based FPGAs

Switching event detection and self-termination programming circuit for energy efficient ReRAM memory arrays

Energy efficiency remains a challenge for the design of non-volatile resistive memories (ReRAMs) arrays. This memory technology suffers from intrinsic variability in switching speed, programming voltages and resistance levels. The programming conditions of memory elements (e.g. pulse widths and amplitudes) must cover the tail bits to avoid programming failures. Switching time of ReRAMs shows wide distributions. Therefore, fast cells are subjects for electrical stress after their switching and energy waste since programming currents are typically large for this technology (tens of µA). In this paper, we present a Write Termination (WT) circuit to stop the programming operation when the switching event occurs in the selected memory element. The proposed design is sensitive to current variations that take place when the memory element switches between two different resistance states (LRS and HRS). This WT scheme reduces the power consumption by 97+%, 93+% and 65+% during Forming, RESET and SET operations respectively. Our estimations show that area efficiency of 70% for a memory array is achievable when the presented WT circuit is integrated in near-memory peripheries. The demonstrated WT circuit is suitable for different ReRAM technologies with small overhead penalty and shows robustness against CMOS and ReRAM variabilities

Accelerating Non-volatile/Hybrid Processor Cache Design Space Exploration for Application Specific Embedded Systems

In this article, we propose a technique to accelerate nonvolatile or hybrid of volatile and nonvolatile processor cache design space exploration for application specific embedded systems. Utilizing a novel cache behavior modeling equation and a new accurate cache miss prediction mechanism, our proposed technique can accelerate NVM or hybrid FIFO processor cache design space exploration for SPEC CPU 2000 applications up to 249 times compared to the conventional approach

GMS: Generic Memristive Structure for Non-Volatile FPGAs

The invention of the memristor enables new possibilities for computation and non-volatile memory storage. In this paper we propose a Generic Memristive Structure (GMS) for 3-D FPGA applications. The GMS cell is demonstrated to be utilized for steering logic useful for multiplexing signals, thus replacing the traditional pass-gates in FPGAs. Moreover, the same GMS cell can be utilized for programmable memories as a replacement for the SRAMs employed in the look-up tables of FPGAs. A fabricated GMS cell is presented and its use in FPGA architecture is demonstrated by the area and delay improvement for several architectural benchmarks

Electrical characterization and modeling of pulse-based forming techniques in RRAM arrays

The forming process, which corresponds to the activation of the switching filament in Resistive Random Access Memory (RRAM) arrays, has a strong impact on the cells’ performances. In this paper we characterize and compare different pulse forming techniques in terms of forming time, yield and cell-to-cell variability on 4 kbits RRAM arrays. Moreover, post-forming modeling during Reset operation of correctly working and over formed cells has been performed. An incremental form and verify technique, based on a sequence of trapezoidal waveforms with increasing voltages followed by a verify operation that terminates when the expected switching behavior has been achieved, showed the best results. This procedure narrows the post-forming current distribution whereas reducing the Reset switching voltage and the operative current. These advantages materialize in a better control of the cell-to-cell variability and in an overall time and energy saving at the system level

Doctor of Philosophy in Computing

dissertationThe demand for main memory capacity has been increasing for many years and will continue to do so. In the past, Dynamic Random Access Memory (DRAM) process scaling has enabled this increase in memory capacity. Along with continued DRAM scaling, the emergence of new technologies like 3D-stacking, buffered Dual Inline Memory Modules (DIMMs), and crosspoint nonvolatile memory promise to continue this trend in the years ahead. However, these technologies will bring with them their own gamut of problems. In this dissertation, I look at the problems facing these technologies from a current delivery perspective. 3D-stacking increases memory capacity available per package, but the increased current requirement means that more pins on the package have to be now dedicated to provide Vdd/Vss, hence increasing cost. At the system level, using buffered DIMMs to increase the number of DRAM ranks increases the peak current requirements of the system if all the DRAM chips in the system are Refreshed simultaneously. Crosspoint memories promise to greatly increase bit densities but have long read latencies because of sneak currents in the cross-bar. In this dissertation, I provide architectural solutions to each of these problems. We observe that smart data placement by the architecture and the Operating System (OS) is a vital ingredient in all of these solutions. We thereby mitigate major bottlenecks in these technologies, hence enabling higher memory densities

Gestión de jerarquías de memoria híbridas a nivel de sistema

Tesis inédita de la Universidad Complutense de Madrid, Facultad de Informática, Departamento de Arquitectura de Computadoras y Automática y de Ku Leuven, Arenberg Doctoral School, Faculty of Engineering Science, leída el 11/05/2017.In electronics and computer science, the term ‘memory’ generally refers to devices that are used to store information that we use in various appliances ranging from our PCs to all hand-held devices, smart appliances etc. Primary/main memory is used for storage systems that function at a high speed (i.e. RAM). The primary memory is often associated with addressable semiconductor memory, i.e. integrated circuits consisting of silicon-based transistors, used for example as primary memory but also other purposes in computers and other digital electronic devices. The secondary/auxiliary memory, in comparison provides program and data storage that is slower to access but offers larger capacity. Examples include external hard drives, portable flash drives, CDs, and DVDs. These devices and media must be either plugged in or inserted into a computer in order to be accessed by the system. Since secondary storage technology is not always connected to the computer, it is commonly used for backing up data. The term storage is often used to describe secondary memory. Secondary memory stores a large amount of data at lesser cost per byte than primary memory; this makes secondary storage about two orders of magnitude less expensive than primary storage. There are two main types of semiconductor memory: volatile and nonvolatile. Examples of non-volatile memory are ‘Flash’ memory (sometimes used as secondary, sometimes primary computer memory) and ROM/PROM/EPROM/EEPROM memory (used for firmware such as boot programs). Examples of volatile memory are primary memory (typically dynamic RAM, DRAM), and fast CPU cache memory (typically static RAM, SRAM, which is fast but energy-consuming and offer lower memory capacity per are a unit than DRAM). Non-volatile memory technologies in Si-based electronics date back to the 1990s. Flash memory is widely used in consumer electronic products such as cellphones and music players and NAND Flash-based solid-state disks (SSDs) are increasingly displacing hard disk drives as the primary storage device in laptops, desktops, and even data centers. The integration limit of Flash memories is approaching, and many new types of memory to replace conventional Flash memories have been proposed. The rapid increase of leakage currents in Silicon CMOS transistors with scaling poses a big challenge for the integration of SRAM memories. There is also the case of susceptibility to read/write failure with low power schemes. As a result of this, over the past decade, there has been an extensive pooling of time, resources and effort towards developing emerging memory technologies like Resistive RAM (ReRAM/RRAM), STT-MRAM, Domain Wall Memory and Phase Change Memory(PRAM). Emerging non-volatile memory technologies promise new memories to store more data at less cost than the expensive-to build silicon chips used by popular consumer gadgets including digital cameras, cell phones and portable music players. These new memory technologies combine the speed of static random-access memory (SRAM), the density of dynamic random-access memory (DRAM), and the non-volatility of Flash memory and so become very attractive as another possibility for future memory hierarchies. The research and information on these Non-Volatile Memory (NVM) technologies has matured over the last decade. These NVMs are now being explored thoroughly nowadays as viable replacements for conventional SRAM based memories even for the higher levels of the memory hierarchy. Many other new classes of emerging memory technologies such as transparent and plastic, three-dimensional(3-D), and quantum dot memory technologies have also gained tremendous popularity in recent years...En el campo de la informática, el término ‘memoria’ se refiere generalmente a dispositivos que son usados para almacenar información que posteriormente será usada en diversos dispositivos, desde computadoras personales (PC), móviles, dispositivos inteligentes, etc. La memoria principal del sistema se utiliza para almacenar los datos e instrucciones de los procesos que se encuentre en ejecución, por lo que se requiere que funcionen a alta velocidad (por ejemplo, DRAM). La memoria principal está implementada habitualmente mediante memorias semiconductoras direccionables, siendo DRAM y SRAM los principales exponentes. Por otro lado, la memoria auxiliar o secundaria proporciona almacenaje(para ficheros, por ejemplo); es más lenta pero ofrece una mayor capacidad. Ejemplos típicos de memoria secundaria son discos duros, memorias flash portables, CDs y DVDs. Debido a que estos dispositivos no necesitan estar conectados a la computadora de forma permanente, son muy utilizados para almacenar copias de seguridad. La memoria secundaria almacena una gran cantidad de datos aun coste menor por bit que la memoria principal, siendo habitualmente dos órdenes de magnitud más barata que la memoria primaria. Existen dos tipos de memorias de tipo semiconductor: volátiles y no volátiles. Ejemplos de memorias no volátiles son las memorias Flash (algunas veces usadas como memoria secundaria y otras veces como memoria principal) y memorias ROM/PROM/EPROM/EEPROM (usadas para firmware como programas de arranque). Ejemplos de memoria volátil son las memorias DRAM (RAM dinámica), actualmente la opción predominante a la hora de implementar la memoria principal, y las memorias SRAM (RAM estática) más rápida y costosa, utilizada para los diferentes niveles de cache. Las tecnologías de memorias no volátiles basadas en electrónica de silicio se remontan a la década de1990. Una variante de memoria de almacenaje por carga denominada como memoria Flash es mundialmente usada en productos electrónicos de consumo como telefonía móvil y reproductores de música mientras NAND Flash solid state disks(SSDs) están progresivamente desplazando a los dispositivos de disco duro como principal unidad de almacenamiento en computadoras portátiles, de escritorio e incluso en centros de datos. En la actualidad, hay varios factores que amenazan la actual predominancia de memorias semiconductoras basadas en cargas (capacitivas). Por un lado, se está alcanzando el límite de integración de las memorias Flash, lo que compromete su escalado en el medio plazo. Por otra parte, el fuerte incremento de las corrientes de fuga de los transistores de silicio CMOS actuales, supone un enorme desafío para la integración de memorias SRAM. Asimismo, estas memorias son cada vez más susceptibles a fallos de lectura/escritura en diseños de bajo consumo. Como resultado de estos problemas, que se agravan con cada nueva generación tecnológica, en los últimos años se han intensificado los esfuerzos para desarrollar nuevas tecnologías que reemplacen o al menos complementen a las actuales. Los transistores de efecto campo eléctrico ferroso (FeFET en sus siglas en inglés) se consideran una de las alternativas más prometedores para sustituir tanto a Flash (por su mayor densidad) como a DRAM (por su mayor velocidad), pero aún está en una fase muy inicial de su desarrollo. Hay otras tecnologías algo más maduras, en el ámbito de las memorias RAM resistivas, entre las que cabe destacar ReRAM (o RRAM), STT-RAM, Domain Wall Memory y Phase Change Memory (PRAM)...Depto. de Arquitectura de Computadores y AutomáticaFac. de InformáticaTRUEunpu

Designing energy-efficient sub-threshold logic circuits using equalization and non-volatile memory circuits using memristors

The very large scale integration (VLSI) community has utilized aggressive complementary metal-oxide semiconductor (CMOS) technology scaling to meet the ever-increasing performance requirements of computing systems. However, as we enter the nanoscale regime, the prevalent process variation effects degrade the CMOS device reliability. Hence, it is increasingly essential to explore emerging technologies which are compatible with the conventional CMOS process for designing highly-dense memory/logic circuits. Memristor technology is being explored as a potential candidate in designing non-volatile memory arrays and logic circuits with high density, low latency and small energy consumption. In this thesis, we present the detailed functionality of multi-bit 1-Transistor 1-memRistor (1T1R) cell-based memory arrays. We present the performance and energy models for an individual 1T1R memory cell and the memory array as a whole. We have considered TiO2- and HfOx-based memristors, and for these technologies there is a sub-10% difference between energy and performance computed using our models and HSPICE simulations. Using a performance-driven design approach, the energy-optimized TiO2-based RRAM array consumes the least write energy (4.06 pJ/bit) and read energy (188 fJ/bit) when storing 3 bits/cell for 100 nsec write and 1 nsec read access times. Similarly, HfOx-based RRAM array consumes the least write energy (365 fJ/bit) and read energy (173 fJ/bit) when storing 3 bits/cell for 1 nsec write and 200 nsec read access times. On the logic side, we investigate the use of equalization techniques to improve the energy efficiency of digital sequential logic circuits in sub-threshold regime. We first propose the use of a variable threshold feedback equalizer circuit with combinational logic blocks to mitigate the timing errors in digital logic designed in sub-threshold regime. This mitigation of timing errors can be leveraged to reduce the dominant leakage energy by scaling supply voltage or decreasing the propagation delay. At the fixed supply voltage, we can decrease the propagation delay of the critical path in a combinational logic block using equalizer circuits and, correspondingly decrease the leakage energy consumption. For a 8-bit carry lookahead adder designed in UMC 130 nm process, the operating frequency can be increased by 22.87% (on average), while reducing the leakage energy by 22.6% (on average) in the sub-threshold regime. Overall, the feedback equalization technique provides up to 35.4% lower energy-delay product compared to the conventional non-equalized logic. We also propose a tunable adaptive feedback equalizer circuit that can be used with sequential digital logic to mitigate the process variation effects and reduce the dominant leakage energy component in sub-threshold digital logic circuits. For a 64-bit adder designed in 130 nm our proposed approach can reduce the normalized delay variation of the critical path delay from 16.1% to 11.4% while reducing the energy-delay product by 25.83% at minimum energy supply voltage. In addition, we present detailed energy-performance models of the adaptive feedback equalizer circuit. This work serves as a foundation for the design of robust, energy-efficient digital logic circuits in sub-threshold regime