Design and analysis of SRAMs for energy harvesting systems

PhD ThesisAt present, the battery is employed as a power source for wide varieties of microelectronic systems ranging from biomedical implants and sensor net-works to portable devices. However, the battery has several limitations and incurs many challenges for the majority of these systems. For instance, the design considerations of implantable devices concern about the battery from two aspects, the toxic materials it contains and its lifetime since replacing the battery means a surgical operation. Another challenge appears in wire-less sensor networks, where hundreds or thousands of nodes are scattered around the monitored environment and the battery of each node should be maintained and replaced regularly, nonetheless, the batteries in these nodes do not all run out at the same time. Since the introduction of portable systems, the area of low power designs has witnessed extensive research, driven by the industrial needs, towards the aim of extending the lives of batteries. Coincidentally, the continuing innovations in the field of micro-generators made their outputs in the same range of several portable applications. This overlap creates a clear oppor-tunity to develop new generations of electronic systems that can be powered, or at least augmented, by energy harvesters. Such self-powered systems benefit applications where maintaining and replacing batteries are impossi-ble, inconvenient, costly, or hazardous, in addition to decreasing the adverse effects the battery has on the environment. The main goal of this research study is to investigate energy harvesting aware design techniques for computational logic in order to enable the capa- II bility of working under non-deterministic energy sources. As a case study, the research concentrates on a vital part of all computational loads, SRAM, which occupies more than 90% of the chip area according to the ITRS re-ports. Essentially, this research conducted experiments to find out the design met-ric of an SRAM that is the most vulnerable to unpredictable energy sources, which has been confirmed to be the timing. Accordingly, the study proposed a truly self-timed SRAM that is realized based on complete handshaking protocols in the 6T bit-cell regulated by a fully Speed Independent (SI) tim-ing circuitry. The study proved the functionality of the proposed design in real silicon. Finally, the project enhanced other performance metrics of the self-timed SRAM concentrating on the bit-line length and the minimum operational voltage by employing several additional design techniques.Umm Al-Qura University, the Ministry of Higher Education in the Kingdom of Saudi Arabia, and the Saudi Cultural Burea

A fully integrated SRAM-based CMOS arbitrary waveform generator for analog signal processing

This dissertation focuses on design and implementation of a fully-integrated SRAM-based arbitrary waveform generator for analog signal processing applications in a CMOS technology. The dissertation consists of two parts: Firstly, a fully-integrated arbitrary waveform generator for a multi-resolution spectrum sensing of a cognitive radio applications, and an analog matched-filter for a radar application and secondly, low-power techniques for an arbitrary waveform generator. The fully-integrated low-power AWG is implemented and measured in a 0.18-¥ìm CMOS technology. Theoretical analysis is performed, and the perspective implementation issues are mentioned comparing the measurement results. Moreover, the low-power techniques of SRAM are addressed for the analog signal processing: Self-deactivated data-transition bit scheme, diode-connected low-swing signaling scheme with a short-current reduction buffer, and charge-recycling with a push-pull level converter for power reduction of asynchronous design. Especially, the robust latch-type sense amplifier using an adaptive-latch resistance and fully-gated ground 10T-SRAM bitcell in a 45-nm SOI technology would be used as a technique to overcome the challenges in the upcoming deep-submicron technologies.Ph.D.Committee Chair: Kim, Jongman; Committee Member: Kang, Sung Ha; Committee Member: Lee, Chang-Ho; Committee Member: Mukhopadhyay, Saibal; Committee Member: Tentzeris, Emmanouil

Low-power and high-performance SRAM design in high variability advanced CMOS technology

As process technologies shrink, the size and number of memories on a chip are exponentially increasing. Embedded SRAMs are a critical component in modern digital systems, and they strongly impact the overall power, performance, and area. To promote memory-related research in academia, this dissertation introduces OpenRAM, a flexible, portable and open-source memory compiler and characterization methodology for generating and verifying memory designs across different technologies.In addition, SRAM designs, focusing on improving power consumption, access time and bitcell stability are explored in high variability advanced CMOS technologies. To have a stable read/write operation for SRAM in high variability process nodes, a differential-ended single-port 8T bitcell is proposed that improves the read noise margin, write noise margin and readout bitcell current by 45%, 48% and 21%, respectively, compared to a conventional 6T bitcell. Also, a differential-ended single-port 12T bitcell for subthreshold operation is proposed that solves the half-select disturbance and allows efficient bit-interleaving. 12T bitcell has a leakage control mechanism which helps to reduce the power consumption and provides operation down to 0.3 V. Both 8T and 12T bitcells are analyzed in a 64 kb SRAM array using 32 nm technology. Besides, to further improve the access time and power consumption, two tracking circuits (multi replica bitline delay and reconfigurable replica bitline delay techniques) are proposed to aid the generation of accurate and optimum sense amplifier set time.An error tolerant SRAM architecture suitable for low voltage video application with dynamic power-quality management is also proposed in this dissertation. This memory uses three power supplies to improve the SRAM stability in low voltages. The proposed triple-supply approach achieves 63% improvement in image quality and 69% reduction in power consumption compared to a single-supply 64 kb SRAM array at 0.70 V

Robust low-power digital circuit design in nano-CMOS technologies

Device scaling has resulted in large scale integrated, high performance, low-power, and low cost systems. However the move towards sub-100 nm technology nodes has increased variability in device characteristics due to large process variations. Variability has severe implications on digital circuit design by causing timing uncertainties in combinational circuits, degrading yield and reliability of memory elements, and increasing power density due to slow scaling of supply voltage. Conventional design methods add large pessimistic safety margins to mitigate increased variability, however, they incur large power and performance loss as the combination of worst cases occurs very rarely. In-situ monitoring of timing failures provides an opportunity to dynamically tune safety margins in proportion to on-chip variability that can significantly minimize power and performance losses. We demonstrated by simulations two delay sensor designs to detect timing failures in advance that can be coupled with different compensation techniques such as voltage scaling, body biasing, or frequency scaling to avoid actual timing failures. Our simulation results using 45 nm and 32 nm technology BSIM4 models indicate significant reduction in total power consumption under temperature and statistical variations. Future work involves using dual sensing to avoid useless voltage scaling that incurs a speed loss. SRAM cache is the first victim of increased process variations that requires handcrafted design to meet area, power, and performance requirements. We have proposed novel 6 transistors (6T), 7 transistors (7T), and 8 transistors (8T)-SRAM cells that enable variability tolerant and low-power SRAM cache designs. Increased sense-amplifier offset voltage due to device mismatch arising from high variability increases delay and power consumption of SRAM design. We have proposed two novel design techniques to reduce offset voltage dependent delays providing a high speed low-power SRAM design. Increasing leakage currents in nano-CMOS technologies pose a major challenge to a low-power reliable design. We have investigated novel segmented supply voltage architecture to reduce leakage power of the SRAM caches since they occupy bulk of the total chip area and power. Future work involves developing leakage reduction methods for the combination logic designs including SRAM peripherals

High performance and energy-efficient instruction cache design and optimisation for ultra-low-power multi-core clusters

High Energy efficiency and high performance are the key regiments for Internet of Things (IoT) end-nodes. Exploiting cluster of multiple programmable processors has recently emerged as a suitable solution to address this challenge. However, one of the main bottlenecks for multi-core architectures is the instruction cache. While private caches fall into data replication and wasting area, fully shared caches lack scalability and form a bottleneck for the operating frequency. Hence we propose a hybrid solution where a larger shared cache (L1.5) is shared by multiple cores connected through a low-latency interconnect to small private caches (L1). However, it is still limited by large capacity miss with a small L1. Thus, we propose a sequential prefetch from L1 to L1.5 to improve the performance with little area overhead. Moreover, to cut the critical path for better timing, we optimized the core instruction fetch stage with non-blocking transfer by adopting a 4 x 32-bit ring buffer FIFO and adding a pipeline for the conditional branch. We present a detailed comparison of different instruction cache architectures' performance and energy efficiency recently proposed for Parallel Ultra-Low-Power clusters. On average, when executing a set of real-life IoT applications, our two-level cache improves the performance by up to 20% and loses 7% energy efficiency with respect to the private cache. Compared to a shared cache system, it improves performance by up to 17% and keeps the same energy efficiency. In the end, up to 20% timing (maximum frequency) improvement and software control enable the two-level instruction cache with prefetch adapt to various battery-powered usage cases to balance high performance and energy efficiency

Low-Power Soft-Error-Robust Embedded SRAM

Soft errors are radiation-induced ionization events (induced by energetic particles like alpha particles, cosmic neutron, etc.) that cause transient errors in integrated circuits. The circuit can always recover from such errors as the underlying semiconductor material is not damaged and hence, they are called soft errors. In nanometer technologies, the reduced node capacitance and supply voltage coupled with high packing density and lack of masking mechanisms are primarily responsible for the increased susceptibility of SRAMs towards soft errors. Coupled with these are the process variations (effective length, width, and threshold voltage), which are prominent in scaled-down technologies. Typically, SRAM constitutes up to 90% of the die in microprocessors and SoCs (System-on-Chip). Hence, the soft errors in SRAMs pose a potential threat to the reliable operation of the system. In this work, a soft-error-robust eight-transistor SRAM cell (8T) is proposed to establish a balance between low power consumption and soft error robustness. Using metrics like access time, leakage power, and sensitivity to single event transients (SET), the proposed approach is evaluated. For the purpose of analysis and comparisons the results of 8T cell are compared with a standard 6T SRAM cell and the state-of-the-art soft-error-robust SRAM cells. Based on simulation results in a 65-nm commercial CMOS process, the 8T cell demonstrates higher immunity to SETs along with smaller area and comparable leakage power. A 32-kb array of 8T cells was fabricated in silicon. After functional verification of the test chip, a radiation test was conducted to evaluate the soft error robustness. As SRAM cells are scaled aggressively to increase the overall packing density, the smaller transistors exhibit higher degrees of process variation and mismatch, leading to larger offset voltages. For SRAM sense amplifiers, higher offset voltages lead to an increased likelihood of an incorrect decision. To address this issue, a sense amplifier capable of cancelling the input offset voltage is presented. The simulated and measured results in 180-nm technology show that the sense amplifier is capable of detecting a 4 mV differential input signal under dc and transient conditions. The proposed sense amplifier, when compared with a conventional sense amplifier, has a similar die area and a greatly reduced offset voltage. Additionally, a dual-input sense amplifier architecture is proposed with corroborating silicon results to show that it requires smaller differential input to evaluate correctly.1 yea

ULTRALOW-POWER, LOW-VOLTAGE DIGITAL CIRCUITS FOR BIOMEDICAL SENSOR NODES

Ph.DDOCTOR OF PHILOSOPH

Ultra Low-power Wireless Sensor Node Design for ECG Sensing Applications

Ubiquitous computing, such as smart homes, smart cars, and smart grid, connects our world closely so that we can easily access to the world through such virtual infrastructural systems. The ultimate vision of this is Internet of Things (IoT) through which intelligent monitoring and management is feasible via networked sensors and actuators. In this system, devices transmit sensed information, and execute instructions distributed via sensor networks. A wireless sensor network (WSN) is such a network where many sensor nodes are interconnected such that a sensor node can transmit information via its adjacent sensor nodes when physical phenomenon is detected. Accordingly, the information can be delivered to the destination through this process. The concept of WSN is also applicable to biomedical applications, especially ECG sensing applications, in a form of a sensor network, so-called body sensor network (BSN), where affixed or implanted biosignal sensors gather bio-signals and transmit them to medical providers. The main challenge of BSN is energy constraint since implanted sensor nodes cannot be replaced easily, so they should prolong with a limited amount of battery energy or by energy harvesting. Thus, we will discuss several power saving techniques in this thesis.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/137081/1/hesed_1.pd

Novel High Performance Ultra Low Power Static Random Access Memories (SRAMs) Based on Next Generation Technologies

Title from PDF of title page viewed January 27, 2021Dissertation advisor: Masud H. ChowdhuryVitaIncludes bibliographical references (page 107-120)Thesis (Ph.D.)--School of Computing and Engineering. University of Missouri--Kansas City, 2019Next Big Thing Is Surely Small: Nanotechnology Can Bring Revolution. Nanotechnology leads the world towards many new applications in various fields of computing, communication, defense, entertainment, medical, renewable energy and environment. These nanotechnology applications require an energy-efficient memory system to compute and process. Among all the memories, Static Random Access Memories (SRAMs) are high performance memories and occupies more than 50% of any design area. Therefore, it is critical to design high performance and energy-efficient SRAM design. Ultra low power and high speed applications require a new generation memory capable of operating at low power as well as low execution time. In this thesis, a novel 8T SRAM design is proposed that offers significantly faster access time and lowers energy consumption along with better read stability and write ability. The proposed design can be used in the conventional SRAM as well as in computationally intensive applications like neural networks and machine learning classifiers [1]-[4]. Novel 8T SRAM design offers higher energy efficiency, reliability, robustness and performance compared to the standard 6T and other existing 8T and 9T designs. It offers the advantages of a 10T SRAM without the additional area, delay and power overheads of the 10T SRAM. The proposed 8T SRAM would be able to overcome many other limitations of the conventional 6T and other 7T, 8T and 9T designs. The design employs single bitline for the write operation, therefore the number of write drivers are reduced. The defining feature of the proposed 8T SRAM is its hybrid design, which is the combination of two techniques: (i) the utilization of single-ended bitline and (ii) the utilization of virtual ground. The single-ended bitline technique ensures separate read and write operations, which eventually reduces the delay and power consumption during the read and write operations. It's independent read and write paths allow the use of the minimum sized access transistors and aid in a disturb-free read operation. The virtual ground weakens the positive feedback in the SRAM cell and improves its write ability. The virtual ground technique is also used to reduce leakages. The proposed design does not require precharging the bitlines for the read operation, which reduces the area and power overheads of the memory system by eliminating the precharging circuit. The design isolates the storage node from the read path, which improves the read stability. For reliability study, we have investigated the static noise margin (SNM) of the proposed 8T SRAM, for which, we have used two methods – (i) the traditional SNM method with the butterfly curve, (ii) the N-curve method A comparative analysis is performed between the proposed and the existing SRAM designs in terms of area, total power consumption during the read and write operations, and stability and reliability. All these advantages make the proposed 8T SRAM design an ideal candidate for the conventional and computationally intensive applications like machine learning classifier and deep learning neural network. In addition to this, there is need for next generation technologies to design SRAM memory because the conventional CMOS technology is approaching its physical and performance boundaries and as a consequence, becoming incompatible with ultra-low-power applications. Emerging devices such as Tunnel Field Effect Transistor (TFET)) and Graphene Nanoribbon Field Effect Transistor (GNRFET) devices are highly potential candidates to overcome the limitations of MOSFET because of their ability to achieve subthreshold slopes below 60 mV/decade and very low leakage currents [6]-[9]. This research also explores novel TFET and GNRFET based 6T SRAM. The thesis evaluates the standby leakage power in the Tunnel FET (TFET) based 6T SRAM cell for different pull-up, pull-down, and pass-gate transistors ratios (PU: PD: PG) and compared to 10nm FinFET based 6T SRAM designs. It is observed that the 10nm TFET based SRAMs have 107.57%, 163.64%, and 140.44% less standby leakage power compared to the 10nm FinFET based SRAMs when the PU: PD: PG ratios are 1:1:1, 1:5:2 and 2:5:2, respectively. The thesis also presents an analysis of the stability and reliability of sub-10nm TFET based 6T SRAM circuit with a reduced supply voltage of 500mV. The static noise margin (SNM), which is a critical measure of SRAM stability and reliability, is determined for hold, read and write operations of the 6T TFET SRAM cell. The robustness of the optimized TFET based 6T SRAM circuit is also evaluated at different supply voltages. Simulations were done in HSPICE and Cadence tools. From the analysis, it is clear that the main advantage of the TFET based SRAM would be the significant improvement in terms of leakage or standby power consumption. Compared to the FinFET based SRAM the standby leakage power of the T-SRAMs are 107.57%, 163.64%, and 140.44% less for 1:1:1, 1:5:2 and 2:5:2 configurations, respectively. Since leakage/standby power is the primary source of power consumption in the SRAM, and the overall system energy efficiency depends on SRAM power consumption, TFET based SRAM would lead to massive improvement of the energy efficiency of the system. Therefore, T-SRAMs are more suitable for ultra-low power applications. In addition to this, the thesis evaluates the standby leakage power of types of Graphene Nanoribbon FETs based 6T SRAM bitcell and compared to 10nm FinFET based 6T SRAM bitcell. It is observed that the 10nm MOS type GNRFET based SRAMs have 16.43 times less standby leakage power compared to the 10nm FinFET based SRAMs. The double gate SB-GNRFET based SRAM consumes 1.35E+03 times less energy compared to the 10nm FinFET based SRAM during write. However, during read double gate SB-GNRFET based SRAM consume 15 times more energy than FinFET based SRAM. It is also observed that GNRFET based SRAMs are more stable and reliable than FinFET based SRAM.Introduction -- Background -- Novel High Performance Ultra Low Power SRAM Design -- Tunnel FET Based SRAM Design -- Graphene Nanoribbon FET Based SRAM Design -- Double-gate FDSOI Based SRAM Designs -- Novel CNTFET and MEMRISTOR Based Digital Designs -- Conclusio