A 3.4pJ FeRAM-enabled D flip-flop in 0.13µm CMOS for nonvolatile processing in digital systems

Nonvolatile processing-continuously operating a digital circuit and retaining state through frequent power interruptions-creates new applications for portable electronics operating from harvested energy and high-performance systems managing power by operating “normally off”. To enable these scenarios, energy processing must happen in parallel with information processing. This work makes the following contributions: 1) the design of a nonvolatile D flip-flop (NVDFF) with embedded ferroelectric capacitors (fecaps) that senses data robustly and avoids race conditions; 2) the integration of the NVDFF into the ASIC design flow with a power management unit (PMU) and a simple one-bit interface to brown-out detection circuitry; and 3) a characterization of the NVDFF statistical signal margin and the energy cost of retaining data.Focus Center Research Program. Focus Center for Circuit & System Solution

Solar Energy Based Self-Sustainable Power Management System

Frequent battery replacement is a big challenge faced in Wireless Sensor Nodes (WSNs) operating in remote places due to high maintenance cost and inaccessibility. The solution for this is harvesting energy from various sources like solar, wind, thermal, vibration. Solar energy harvesting is the best option among them because of its abundant availability. The battery gets charged through solar energy during daylight and when solar energy is not available, the system gets power up through the charge stored in the battery. The Maximum Power Point (MPP) of the solar cell is tracked by comparing the MPP voltage with respect to the input solar cell voltage. The reference MPP voltage is generated by sampling 0.7 times the open circuit voltage (VOC ) of solar cell periodically in a capacitor (CMP P ). A self sustainable high power battery management system is developed where the system works in two modes, the first one is the main converter mode and the second is the startup mode. startup mode is used when the battery is almost drained. None of the other control circuitry function in this mode. Cold start circuit only goal is to charge output capacitance until it crosses the threshold voltage required to power the entire system. Power On Reset (POR) circuit decides between startup mode and main converter mode

A 3.4pJ FeRAM-enabled D flip-flop in 0.13µm CMOS for nonvolatile processing in digital systems

Nonvolatile processing-continuously operating a digital circuit and retaining state through frequent power interruptions-creates new applications for portable electronics operating from harvested energy and high-performance systems managing power by operating “normally off”. To enable these scenarios, energy processing must happen in parallel with information processing. This work makes the following contributions: 1) the design of a nonvolatile D flip-flop (NVDFF) with embedded ferroelectric capacitors (fecaps) that senses data robustly and avoids race conditions; 2) the integration of the NVDFF into the ASIC design flow with a power management unit (PMU) and a simple one-bit interface to brown-out detection circuitry; and 3) a characterization of the NVDFF statistical signal margin and the energy cost of retaining data.Focus Center Research Program. Focus Center for Circuit & System Solution

Energy harvesting towards self-powered iot devices

The internet of things (IoT) manages a large infrastructure of web-enabled smart devices, small devices that use embedded systems, such as processors, sensors, and communication hardware to collect, send, and elaborate on data acquired from their environment. Thus, from a practical point of view, such devices are composed of power-efficient storage, scalable, and lightweight nodes needing power and batteries to operate. From the above reason, it appears clear that energy harvesting plays an important role in increasing the efficiency and lifetime of IoT devices. Moreover, from acquiring energy by the surrounding operational environment, energy harvesting is important to make the IoT device network more sustainable from the environmental point of view. Different state-of-the-art energy harvesters based on mechanical, aeroelastic, wind, solar, radiofrequency, and pyroelectric mechanisms are discussed in this review article. To reduce the power consumption of the batteries, a vital role is played by power management integrated circuits (PMICs), which help to enhance the system's life span. Moreover, PMICs from different manufacturers that provide power management to IoT devices have been discussed in this paper. Furthermore, the energy harvesting networks can expose themselves to prominent security issues putting the secrecy of the system to risk. These possible attacks are also discussed in this review article

A 1.1 nW Energy-Harvesting System with 544 pW Quiescent Power for Next-Generation Implants

This paper presents a nW power management unit (PMU) for an autonomous wireless sensor that sustains itself by harvesting energy from the endocochlear potential (EP), the 70-100 mV electrochemical bio-potential inside the mammalian ear. Due to the anatomical constraints inside the inner ear, the total extractable power from the EP is limited close to 1.1-6.25 nW. A nW boost converter is used to increase the input voltage (30-55 mV) to a higher voltage (0.8-1.1 V) usable by CMOS circuits in the sensor. A pW charge pump circuit is used to minimize the leakage in the boost converter. Furthermore, ultralow-power control circuits consisting of digital implementations of input impedance adjustment circuits and zero current switching circuits along with Timer and Reference circuits keep the quiescent power of the PMU down to 544 pW. The designed boost converter achieves a peak power conversion efficiency of 56%. The PMU can sustain itself, and a duty-cyled ultralow-power load while extracting power from the EP of a live guinea pig. The PMU circuits have been implemented on a 0.18- μm CMOS process.Semiconductor Research Corporation. Focus Center for Circuit and System Solutions (C2S2)Interconnect Focus Center (United States. Defense Advanced Research Projects Agency and Semiconductor Research Corporation)National Institutes of Health (U.S.) (Grant K08 DC010419)National Institutes of Health (U.S.) (Grant T32 DC00038)Bertarelli Foundatio

Efficient Archietecture for Effective Utilization of Harvested Power in Microscale Energy Harvesting

Recent developments in combining sensors, microprocessors, and radio frequency (RF) communications holds the potential to revolutionize the way we monitor and maintain critical systems. In the future, literally billions of wireless sensors may become deeply embedded within machines, structures, and the environment. Sensed information will be automatically collected, compressed, and forwarded for condition based maintenance. Energy Harvesting comprises a promising solution to one of the key problems faced by battery-powered Wireless Sensor Networks, namely the limited nature of the energy supply (finite battery capacity). By harvesting energy from the surrounding environment, the sensors can have a continuous lifetime without any needs for battery recharge or replacement

Design of low-voltage integrated step-up oscillators with microtransformers for energy harvesting applications

This paper describes the modeling of startup circuits in battery-less micropower energy harvesting systems and investigates the use of bond wire micromagnetics. The analysis focuses on step-up Meissner oscillators based on magnetic core transformers operating with input voltages down to ≈100 mV, e.g. from thermoelectric generators. As a key point, this paper examines the effect of core losses and leakage inductances on the startup requirements obtained with the classical Barkhausen criterion, and demonstrates the minimum transconductance for oscillations to occur. For validation purposes, a step-up oscillator IC is fabricated in a STMicroelectronics 0.32 μm technology, and connected to two bond-wire microtransformers, respectively, with a 1:38 MnZn ferrite core and with a 1:52 ferromagnetic low-temperature co-fired ceramic (LTCC) core. Coherently with the proposed model, experimental measurements show a minimum startup voltage of 228 mV for the MnZn ferrite core and of 104 mV for the LTCC core

A 32 mV/69 mV input voltage booster based on a piezoelectric transformer for energy harvesting applications

This paper presents a novel method for battery-less circuit start-up from ultra-low voltage energy harvesting sources. The approach proposes for the first time the use of a Piezoelectric Transformer (PT) as the key component of a step-up oscillator. The proposed oscillator circuit is first modelled from a theoretical point of view and then validated experimentally with a commercial PT. The minimum achieved start-up voltage is about 69 mV, with no need for any external magnetic component. Hence, the presented system is compatible with the typical output voltages of thermoelectric generators (TEGs). Oscillation is achieved through a positive feedback coupling the PT with an inverter stage made up of JFETs. All the used components are in perspective compatible with microelectronic and MEMS technologies. In addition, in case the use of a ∼40 μH inductor is acceptable, the minimum start-up voltage becomes as low as about 32 mV

Efficient power management circuits for energy harvesting applications

Low power IoT devices are growing in numbers and by 2020 there will be more than 25 Billion of those in areas such as wearables, smart homes, remote surveillance, transportation and industrial systems, including many others. Many IoT electronics either will operate from stand-alone energy supply (e.g., battery) or be self-powered by harvesting from ambient energy sources or have both options. Harvesting sustainable energy from ambient environment plays significant role in extending the operation lifetime of these devices and hence, lower the maintenance cost of the system, which in turn help make them integral to simpler systems. Both for battery-powered and harvesting capable systems, efficient power delivery unit remains an essential component for maximizing energy efficiency. The goal of this research is to investigate the challenges of energy delivery for low power electronics considering both energy harvesting as well as battery-powered conditions and to address those challenges. Different challenges of energy harvesting from low voltage energy sources based on the limitations of the sources, the type of the regulator used and the pattern of the load demands have been investigated. Different aspects of the each challenges are further investigated to seek optimized solutions for both load specific and generalized applications. A voltage boost mechanism is chosen as the primary mechanism to investigate and to addressing those challenges, befitting the need for low power applications which often rely on battery voltage or on low voltage energy harvesting sources. Additionally, a multiple output buck regulator is also discussed. The challenges analyzed include very low voltage start up issues for an inductive boost regulator, cascading of boost regulator stages, and reduction of the number of external component through reusing those. Design techniques for very high conversion ratio, bias current reduction with autonomous bias gating, battery-less cold start, component and power stage multiplexing for reconfigurable and multi-domain regulators are presented. Measurement results from several silicon prototypes are also presented.Ph.D