A linear high-efficiency millimeter-wave CMOS Doherty radiator leveraging on-antenna active load-modulation

This thesis presents a Doherty Radiator architecture that explores multi-feed antennas to achieve an on-antenna Doherty load modulation network and demonstrate high-speed high-efficiency transmission of wideband modulated signals. On the passive circuits, we exploit the multi-feed antenna concept to realize compact and high-efficiency on-antenna active load modulation for close-to-ideal Doherty operation, on-antenna power combining, and mm-Wave signal radiation. Moreover, we analyze the far-field transmission of the proposed Doherty Radiator and demonstrate its wide Field-of-View (FoV). On the active circuits, we employ a GHz-bandwidth adaptive biasing at the Doherty Auxiliary power amplifier (PA) path to enhance the Main/Auxiliary Doherty cooperation and appropriate turning-on/-off of the Auxiliary path. A proof-of-concept Doherty Radiator implemented in a 45nm CMOS SOI process over 62-68GHz exhibits a consistent 1.45-1.53× PAE enhancement at 6dB PBO over an idealistic class-B PA with the same PAE at P1dB. The measured Continuous-Wave (CW) performance at 65GHz demonstrates 19.4/19.2dBm PSAT/P1dB and achieves 27.5%/20.1% PAE at peak/6dB PBO, respectively. For single-carrier 1Gsym/s 64-QAM modulation, the Doherty Radiator shows average output power of 14.2dBm with an average 20.2% PAE and -26.7dB EVM without digital predistortion. Consistent EVMs are observed over the entire antenna FoV, demonstrating spatially undistorted transmission and constant Doherty PBO efficiency enhancement.M.S

Four-element phased-array beamformers and a self-interference canceling full-duplex transciver in 130-nm SiGe for 5G applications at 26 GHz

This thesis is on the design of radio-frequency (RF) integrated front-end circuits for next generation 5G communication systems. The demand for higher data rates and lower latency in 5G networks can only be met using several new technologies including, but not limited to, mm-waves, massive-MIMO, and full-duplex. Use of mm-waves provides more bandwidth that is necessary for high data rates at the cost of increased attenuation in air. Massive-MIMO arrays are required to compensate for this increased path loss by providing beam steering and array gain. Furthermore, full duplex operation is desirable for improved spectrum efficiency and reduced latency. The difficulty of full duplex operation is the self-interference (SI) between transmit (TX) and receive (RX) paths. Conventional methods to suppress this interference utilize either bulky circulators, isolators, couplers or two separate antennas. These methods are not suitable for fully-integrated full-duplex massive-MIMO arrays. This thesis presents circuit and system level solutions to the issues summarized above, in the form of SiGe integrated circuits for 5G applications at 26 GHz. First, a full-duplex RF front-end architecture is proposed that is scalable to massive-MIMO arrays. It is based on blind, RF self-interference cancellation that is applicable to single/shared antenna front-ends. A high resolution RF vector modulator is developed, which is the key building block that empowers the full-duplex frontend architecture by achieving better than state-of-the-art 10-b monotonic phase control. This vector modulator is combined with linear-in-dB variable gain amplifiers and attenuators to realize a precision self-interference cancellation circuitry. Further, adaptive control of this SI canceler is made possible by including an on-chip low-power IQ downconverter. It correlates copies of transmitted and received signals and provides baseband/dc outputs that can be used to adaptively control the SI canceler. The solution comes at the cost of minimal additional circuitry, yet significantly eases linearity requirements of critical receiver blocks at RF/IF such as mixers and ADCs. Second, to complement the proposed full-duplex front-end architecture and to provide a more complete solution, high-performance beamformer ICs with 5-/6- b phase and 3-/4-b amplitude control capabilities are designed. Single-channel, separate transmitter and receiver beamformers are implemented targeting massive- MIMO mode of operation, and their four-channel versions are developed for phasedarray communication systems. Better than state-of-the-art noise performance is obtained in the RX beamformer channel, with a full-channel noise figure of 3.3 d

22-32 GHz Low-Noise Amplifier Design in 22-nm CMOS-SOI Technology

This thesis explores the use of a 22-nm CMOS-SOI technology in the design of a two-stage amplifier which targets wide bandwidth, low noise and modest linearity in the 28 GHz band. A design methodology with a transformer-coupled, noise-matching interstage is presented for minimizing the noise factor of the two-stage amplifier. Furthermore, benefits of interstage noise matching are discussed. Next, a transistor layout for minimizing noise and maintaining sufficient electromigration reliability is described. It is followed by an analysis of transformer configurations and a transformer layout example is depicted. To verify the design methodology, two amplifier prototypes with noise-matching interstage were fabricated. Measurement shows that the first design achieves a peak gain of 20.7 dB and better-than-10-dB input and output return losses within a frequency range of 22.5 to 32.2 GHz. The lowest noise figure of 1.81 dB is achieved within the frequency range. Input IP3 of -13.4 dBm is achieved with the cost of 17.3 mW DC power consumption. When the bias at the back-gate is lowered from 2 V to 0.62 V, the power consumption is decreased to 5.6 mW and the peak gain drops down to 17.9 dB. Minimum noise figure increases from 1.81 to 2.13 dB and input IP3 drops to -14.4 dBm. The folded output stage in the second design improves the input IP3 to -6.7 dBm at the cost of 35 mW total power consumption. The peak gain of the second design is 20.1 dB, and the lowest noise figure of 1.73 dB within a frequency range of 23.8 to 32.4 GHz. Both designs occupy about 0.05 mm2 active area