A 0.5-to-2.5 Gb/s Reference-Less Half-Rate Digital CDR With Unlimited Frequency Acquisition Range and Improved Input Duty-Cycle Error Tolerance

A reference-less highly digital half-rate clock and data recovery (CDR) circuit with improved tolerance to input duty cycle error is presented. Using a chain of frequency dividers, the proposed frequency detector produces a known sub-harmonic tone from the incoming random data. A digital frequency-locked loop uses the extracted tone, and drives the oscillator to any sub-rate of the input data frequency. The early/late outputs of a conventional half-rate bang-bang phase detector are used to determine the duty-cycle error in the incoming random data and adjust the oscillator clock phases to maximize receiver timing margins. Fabricated in 0.13 μm CMOS technology, the prototype digital CDR operates without any errors from 0.5 Gb/s to 2.5 Gb/s. At 2 Gb/s, the prototype consumes 6.1 mW power from a 1.2V supply. The proposed clock-phase calibration is capable of correcting up to ±20% of input data duty-cycle error.This is the author's peer-reviewed final manuscript, as accepted by the publisher. The published article is copyrighted by IEEE-Institute of Electrical and Electronics Engineers and can be found at: http://ieeexplore.ieee.org/xpl/RecentIssue.jsp?punumber=4.Keywords: data duty cycle error, optimal sampling, clock phase calibration, power spectral density of random NRZ data, linear delay cell, Digital CDR, reference-less frequency acquisitio

통계적 주파수 검출기 기반 기준 주파수를 사용하지 않는 클록 및 데이터 복원 회로의 설계 방법론

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 정덕균.In this thesis, a design of a high-speed, power-efficient, wide-range clock and data recovery (CDR) without a reference clock is proposed. A frequency acquisition scheme using a stochastic frequency detector (SFD) based on the Alexander phase detector (PD) is utilized for the referenceless operation. Pat-tern histogram analysis is presented to analyze the frequency acquisition behavior of the SFD and verified by simulation. Based on the information obtained by pattern histogram analysis, SFD using autocovariance is proposed. With a direct-proportional path and a digital integral path, the proposed referenceless CDR achieves frequency lock at all measurable conditions, and the measured frequency acquisition time is within 7μs. The prototype chip has been fabricated in a 40-nm CMOS process and occupies an active area of 0.032 mm2. The proposed referenceless CDR achieves the BER of less than 10-12 at 32 Gb/s and exhibits an energy efficiency of 1.15 pJ/b at 32 Gb/s with a 1.0 V supply.본 논문은 기준 클럭이 없는 고속, 저전력, 광대역으로 동작하는 클럭 및 데이터 복원회로의 설계를 제안한다. 기준 클럭이 없는 동작을 위해서 알렉산더 위상 검출기에 기반한 통계적 주파수 검출기를 사용하는 주파수 획득 방식이 사용된다. 통계적 주파수 검출기의 주파수 추적 양상을 분석하기 위해 패턴 히스토그램 분석 방법론을 제시하였고 시뮬레이션을 통해 검증하였다. 패턴 히스토그램 분석을 통해 얻은 정보를 바탕으로 자기공분산을 이용한 통계적 주파수 검출기를 제안한다. 직접 비례 경로와 디지털 적분 경로를 통해 제안된 기준 클럭이 없는 클럭 및 데이터 복원회로는 모든 측정 가능한 조건에서 주파수 잠금을 달성하는 데 성공하였고, 모든 경우에서 측정된 주파수 추적 시간은 7μs 이내이다. 40-nm CMOS 공정을 이용하여 만들어진 칩은 0.032 mm2의 면적을 차지한다. 제안하는 클럭 및 데이터 복원회로는 32 Gb/s의 속도에서 비트에러율 10-12 이하로 동작하였고, 에너지 효율은 32Gb/s의 속도에서 1.0V 공급전압을 사용하여 1.15 pJ/b을 달성하였다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 13 CHAPTER 2 BACKGROUNDS 14 2.1 CLOCKING ARCHITECTURES IN SERIAL LINK INTERFACE 14 2.2 GENERAL CONSIDERATIONS FOR CLOCK AND DATA RECOVERY 24 2.2.1 OVERVIEW 24 2.2.2 JITTER 26 2.2.3 CDR JITTER CHARACTERISTICS 33 2.3 CDR ARCHITECTURES 39 2.3.1 PLL-BASED CDR – WITH EXTERNAL REFERENCE CLOCK 39 2.3.2 DLL/PI-BASED CDR 44 2.3.3 PLL-BASED CDR – WITHOUT EXTERNAL REFERENCE CLOCK 47 2.4 FREQUENCY ACQUISITION SCHEME 50 2.4.1 TYPICAL FREQUENCY DETECTORS 50 2.4.1.1 DIGITAL QUADRICORRELATOR FREQUENCY DETECTOR 50 2.4.1.2 ROTATIONAL FREQUENCY DETECTOR 54 2.4.2 PRIOR WORKS 56 CHAPTER 3 DESIGN OF THE REFERENCELESS CDR USING SFD 58 3.1 OVERVIEW 58 3.2 PROPOSED FREQUENCY DETECTOR 62 3.2.1 MOTIVATION 62 3.2.2 PATTERN HISTOGRAM ANALYSIS 68 3.2.3 INTRODUCTION OF AUTOCOVARIANCE TO STOCHASTIC FREQUENCY DETECTOR 75 3.3 CIRCUIT IMPLEMENTATION 83 3.3.1 IMPLEMENTATION OF THE PROPOSED REFERENCELESS CDR 83 3.3.2 CONTINUOUS-TIME LINEAR EQUALIZER (CTLE) 85 3.3.3 DIGITALLY-CONTROLLED OSCILLATOR (DCO) 87 3.4 MEASUREMENT RESULTS 89 CHAPTER 4 CONCLUSION 99 APPENDIX A DETAILED FREQUENCY ACQUISITION WAVEFORMS OF THE PROPOSED SFD 100 BIBLIOGRAPHY 108 초 록 122박

데이터 전송로 확장성과 루프 선형성을 향상시킨 다중채널 수신기들에 관한 연구

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2013. 2. 정덕균.Two types of serial data communication receivers that adopt a multichannel architecture for a high aggregate I/O bandwidth are presented. Two techniques for collaboration and sharing among channels are proposed to enhance the loop-linearity and channel-expandability of multichannel receivers, respectively. The first proposed receiver employs a collaborative timing scheme recovery which relies on the sharing of all outputs of phase detectors (PDs) among channels to extract common information about the timing and multilevel signaling architecture of PAM-4. The shared timing information is processed by a common global loop filter and is used to update the phase of the voltage-controlled oscillator with better rejection of per-channel noise. In addition to collaborative timing recovery, a simple linearization technique for binary PDs is proposed. The technique realizes a high-rate oversampling PD while the hardware cost is equivalent to that of a conventional 2x-oversampling clock and data recovery. The first receiver exploiting the collaborative timing recovery architecture is designed using 45-nm CMOS technology. A single data lane occupies a 0.195-mm2 area and consumes a relatively low 17.9 mW at 6 Gb/s at 1.0V. Therefore, the power efficiency is 2.98 mW/Gb/s. The simulated jitter is about 0.034 UI RMS given an input jitter value of 0.03 UI RMS, while the relatively constant loop bandwidth with the PD linearization technique is about 7.3-MHz regardless of the data-stream noise. Unlike the first receiver, the second proposed multichannel receiver was designed to reduce the hardware complexity of each lane. The receiver employs shared calibration logic among channels and yet achieves superior channel expandability with slim data lanes. A shared global calibration control, which is used in a forwarded clock receiver based on a multiphase delay-locked loop, accomplishes skew calibration, equalizer adaptation, and the phase lock of all channels during a calibration period, resulting in reduced hardware overhead and less area required by each data lane. The second forwarded clock receiver is designed in 90-nm CMOS technology. It achieves error-free eye openings of more than 0.5 UI across 9− 28 inch Nelco 4000-6 microstrips at 4− 7 Gb/s and more than 0.42 UI at data rates of up to 9 Gb/s. The data lane occupies only 0.152 mm2 and consumes 69.8 mW, while the rest of the receiver occupies 0.297 mm2 and consumes 56 mW at a data rate of 7 Gb/s and a supply voltage of 1.35 V.1. Introduction 1 1.1 Motivations 1.2 Thesis Organization 2. Previous Receivers for Serial-Data Communications 2.1 Classification of the Links 2.2 Clocking architecture of transceivers 2.3 Components of receiver 2.3.1 Channel loss 2.3.2 Equalizer 2.3.3 Clock and data recovery circuit 2.3.3.1. Basic architecture 2.3.3.2. Phase detector 2.3.3.2.1. Linear phase detector 2.3.3.2.2. Binary phase detector 2.3.3.3. Frequency detector 2.3.3.4. Charge pump 2.3.3.5. Voltage controlled oscillator and delay-line 2.3.4 Loop dynamics of PLL 2.3.5 Loop dynamics of DLL 3. The Proposed PLL-Based Receiver with Loop Linearization Technique 3.1 Introduction 3.2 Motivation 3.3 Overview of binary phase detection 3.4 The proposed BBPD linearization technique 3.4.1 Architecture of the proposed PLL-based receiver 3.4.2 Linearization technique of binary phase detection 3.4.3 Rotational pattern of sampling phase offset 3.5 PD gain analysis and optimization 3.6 Loop Dynamics of the 2nd-order CDR 3.7 Verification with the time-accurate behavioral simulation 3.8 Summary 4. The Proposed DLL-Based Receiver with Forwarded-Clock 4.1 Introduction 4.2 Motivation 4.3 Design consideration 4.4 Architecture of the proposed forwarded-clock receiver 4.5 Circuit description 4.5.1 Analog multi-phase DLL 4.5.2 Dual-input interpolating deley cells 4.5.3 Dedicated half-rate data samplers 4.5.4 Cherry-Hooper continuous-time linear equalizer 4.5.5 Equalizer adaptation and phase-lock scheme 4.6 Measurement results 5. Conclusion 6. BibliographyDocto