Adjustable support spring

Restraining spring mechanism acting against a force has adjustable spring constant, and its performance is not affected by changes in ambient pressure. Natural frequency of device is varied by changing absolute pressures within bellows and may be tuned to prevent coupling while maintaining a given spring constant

Improved circuit-board interconnectors

One component serves three functions, electrical interconnections, thermal control, and mechanical integrity, at same time. Several versions of design: (1) Insulated support plate contains holes; (2) Alternate support plate configuration uses rivets instead of pins; and (3) Another configuration includes leaf-spring contacts instead of pins or rivets

Shock-operated valve would automatically protect fluid systems

Glandless valve shuts down high-pressure fluid systems when severe shock from an explosion or earthquake occurs. The valve uses a pendulum to support the valve closure plug in the open position. When jarred, the valve body is moved relative to the pendulum and the plug support is displaced, allowing the plug to seat and be held by spring pressure

Modal couping effects in the free vibration of elastically interconnected beams

The problem of free vibration of a uniform beam elastically interconnected to a cantilevered beam, representing an idealized launch vehicle aeroelastic model in a wind tunnel, is studied. With elementary beam theory modelling, numerical results are obtained for the frequencies, mode shapes and the generalized modal mass of this elastically cou pled13; system, for a range of values of the spring constants and cantilevered beam stiffness and inertia values. The study shows that when the linear springs are supported at the nodal points corresponding to the first free-free beam mode, the modal interaction comes primarily from the rotational spring stiffness. The effect of the linear spring stiffness on the higher model modes is also found to be marginal. However, the rotational stiffness has a significant effect on all the predominantly model modes as it couples the model13; deformations and the support rod deformations. The study also shows that though the variations in the stiffness or the inertia values of the cantilever beam affect only the13; predominantly cantilever modes, these variations become important because of the fact that the cantilevered support rod frequencies may come close to, or even cross over, the13; predominantly model mode frequencies. The results also bring out the fact that shifting of the support points away from the first mode nodal points has a maximum effect only on the first model mode

Model support roll balance and roll coupling

The design concepts of two specialized wind tunnel model support mechanisms are described. The forced oscillation roll balance mechanism was designed to meet the specific requirement to measure aerodynamic forces and moments to permit determination of the damping-in-roll parameters of winged configurations. A variable speed motor is used to oscillate the model by means of an offset crank. The oscillating motion is resisted by a torsion spring to provide a restoring torque and is attached to the section forward of the strain-gage balance. This spring action allows the model to be oscillated at a frequency for velocity resonance, whereby the mechanical spring and any aerodynamic spring balance. This spring action allows the model to be oscillated at a frequency for velocity resonance, whereby the mechanical spring and any aerodynamic spring balance out the model inertia. The only torque then required to oscillate the model at that particular frequency is equal to that due to aerodynamic damping. The second mechanism, a roll coupling for remotely rotating a model, was designed to invert or roll a model about its longitudinal axis when mounted for testing

Electrical servo actuator bracket

An electrical servo actuator is mounted on a support arm which is allowed to pivot on a bolt through a fixed mounting bracket. The actuator is pivotally connected to the end of the support arm by a bolt which has an extension allowed to pass through a slot in the fixed mounting bracket. An actuator rod extends from the servo actuator to a crank arm which turns a control shaft. A short linear thrust of the rod pivots the crank arm through about 90 for full-on control with the rod contracted into the servo actuator, and full-off control when the rod is extended from the actuator. A spring moves the servo actuator and actuator rod toward the control crank arm once the actuator rod is fully extended in the full-off position. This assures the turning of the control shaft to a full-off position. A stop bolt and slot are provided to limit pivot motion. Once fully extended, the spring pivots the motion

Science subject leader development materials: Spring 2010

These are the materials from the spring 2010 science subject leader development meetings (SLDM). They provide support and challenge for science departments within the 'Narrowing the Gaps' agenda by focusing on strengthening science learning and teaching. Comprises tutor notes, slide presentation, slide handouts and activity handouts

Diversity & Inclusion Update - Spring 2017

This Spring 2017 newsletter discusses ongoing campus initiatives to facilitate diversity and inclusion efforts on campus. Topics discussed include continued changes inspired by the January 2016 Town Hall meeting, such as the invitation of new sororities and fraternities to campus, as well as new student and administrative initiatives, such as the organization of the Student Solidarity Rally on March 1st 2017 and college grants received to promote and support diversity