Turn-to-turn fault protection technique for synchronous machines without additional voltage transformers

This paper presents a novel protection technique for the detection of inter-turn faults in synchronous machines. It is based on the calculation of voltage in the stator windings from the usual phases and neutral voltage, typically available in allgenerator protection relays. The existing turn-to-turn protection mechanisms require additional voltage transformers. The main contribution of this technique is that it can be implemented without using any additional voltage transformers. Thistechnique has been successfully tested in a special synchronous machine with taps in the stator windings, where turn-to-turn faults have been created

Thermally induced mechanical stress in the stator windings of electrical machines

The lifetime of an electrical machine mainly depends on the thermal overloading. Modern day applications of electrical machines on one hand require compact machines with high power density, while on the other hand force electrical machines to undergo frequent temperature cycling. Until recently, in the case of electrical machines, the main factor related to the degradation of the winding insulation was thought to be the thermal oxidization of the insulation materials. It has now been revealed that thermal overloading can also induce mechanical stress in the windings of electrical machines, which over time could lead to fatigue and degradation. In this paper, a comprehensive study of the thermally induced mechanical stress in the windings of an electrical machine is presented. The study is performed using combined thermo-mechanical models. The numerical results are validated by experiments on a segmented stator winding set-up

A novel dual-stator hybrid excited synchronous wind generator

This paper presents a novel dual-stator hybrid excited synchronous wind generator and describes its structural features and operation principle. The no-load magnetic fields with different field currents are computed by 3-D finite-element method. Static characteristics, including the flux-linkage and EMF waveforms of stator windings, and inductance waveforms of armature windings and field winding, are analyzed. The simulation results show that due to the dual-stator structure, the air-gap magnetic flux can be easily controlled, while the output voltage can be increased effectively. Tests are performed on the prototype machine to validate the predicted results, and an excellent agreement is obtained

General modeling of the windings for multi-phase ac machines

This paper, which deals with the winding modeling of ac multi-phase machines with a regular distribution of the stator slots, details an original matrix modeling of the stator winding. First, the properties of the balanced multi-phase windings (with integral-slot and fractional-slot patterns) are analysed. The winding function approach, one of the most common way to model the winding distribution effects on the stator rotating field, is then introduced. For multi-phase machines, it will be shown that the pole number generated by the winding distribution depends on a new parameter: the circularity index. The discrete nature of the winding, imposed by the stator slots, leads to the development of a discrete modeling of the winding obtained from sampling the winding function: two matrices, the winding function matrix and the distribution function matrix, are introduced to characterize the multi-phase winding. This matrix approach is thus a concise way to calculate the winding factors and to estimate the set of self and mutual stator inductances for smooth air gap multi-phase machines. A particularly original method of obtaining an analytical expression for the leakage mutual inductance is described. The results are validated with two experimental 5-phase PM machines by using experimental measurements and numerical simulations

Computationally Efficient Strand Eddy Current Loss Calculation in Electric Machines

A fast finite element (FE) based method for the calculation of eddy current losses in the stator windings of randomly wound electric machines is presented in this paper. The method is particularly suitable for implementation in large-scale design optimization algorithms where a qualitative characterization of such losses at higher speeds is most beneficial for identification of the design solutions that exhibit the lowest overall losses including the ac losses in the stator windings. Unlike the common practice of assuming a constant slot fill factor s f for all the design variations, the maximum s f in the developed method is determined based on the individual slot structure/dimensions and strand wire specifications. Furthermore, in lieu of detailed modeling of the conductor strands in the initial FE model, which significantly adds to the complexity of the problem, an alternative rectangular coil modeling subject to a subsequent flux mapping technique for determination of the impinging flux on each individual strand is pursued. Rather than pursuing the precise estimation of ac conductor losses, the research focus of this paper is placed on the development of a computationally efficient technique for the derivation of strand eddy current losses applicable in design optimization, especially where both the electromagnetic and thermal machine behavior are accounted for. A fractional-slot concentrated winding permanent magnet synchronous machine is used for the purpose of this study due to the higher slot leakage flux and slot opening fringing flux of such machines, which are the major contributors to strand eddy current losses in the windings. The analysis is supplemented with an investigation on the influence of the electrical loading on ac winding loss effects for this machine design, a subject that has received less attention in the literature. Experimental ac loss measurements on a 12-slot 10-pole stator assembly will be discussed to verify the existing trends in the simulation result

Investigations on the performances of the electrical generator of a rim-driven marine current turbine”

In this paper, the electrical generator of a rim-driven horizontal-axis current turbine is modeled in detail. Its main characteristics and performances are evaluated (efficiency, mass, cost, etc). This generator is of permanent magnet direct-driven synchronous type and is connected to a variable speed power electronics drive. It is then compared to a more traditional technology (a pod generator) in terms of mass and cost for a common set of specification. In addition, due to the specific geometry of the machine, the use of low-cost ferrite magnets is investigated in place of NdFeB magnets

Improved transient simulation of salient-pole synchronous generators with internal and ground faults in the stator winding

An improved model for simulating the transient behavior of salient-pole synchronous generators with internal and ground faults in the stator winding is established using the multi-loop circuit method. The model caters for faults under different ground conditions for the neutral, and accounts for the distributed capacitances of the windings to ground. Predictions from the model are validated by experiments, and it is shown that the model accurately predicts the voltage and current waveforms under fault conditions. Hence, it can be used to analyze important features of faults and to design appropriate protection schemes

Permanent-magnet brushless machines with unequal tooth widths and similar slot and pole numbers

This paper presents a comparative study of three-phase permanent-magnet brushless machines in which the slot and pole numbers are similar, with reference to conventional brushless dc machines in which the ratio of the slot number to pole number is usually 3 : 2. Three different motor designs are considered. Two have equal tooth widths, with one having a coil wound on every tooth and the other only having a coil wound on alternate teeth, while the third machine also has coils wound on alternate teeth but these are wider than the unwound teeth while the width of their tooth tips is almost equal to the rotor pole pitch in order to maximize the flux linkage and torque. Analytical and finite-element methods are employed to predict the flux-linkage and back-electromotive-force waveforms, and the self- and mutual-inductances, and these are shown to be in good agreement with measured results. It is also shown that the third machine is eminently appropriate for brushless dc operation

Multiphase induction motor drives - a technology status review

The area of multiphase variable-speed motor drives in general and multiphase induction motor drives in particular has experienced a substantial growth since the beginning of this century. Research has been conducted worldwide and numerous interesting developments have been reported in the literature. An attempt is made to provide a detailed overview of the current state-of-the-art in this area. The elaborated aspects include advantages of multiphase induction machines, modelling of multiphase induction machines, basic vector control and direct torque control schemes and PWM control of multiphase voltage source inverters. The authors also provide a detailed survey of the control strategies for five-phase and asymmetrical six-phase induction motor drives, as well as an overview of the approaches to the design of fault tolerant strategies for post-fault drive operation, and a discussion of multiphase multi-motor drives with single inverter supply. Experimental results, collected from various multiphase induction motor drive laboratory rigs, are also included to facilitate the understanding of the drive operatio