Heat transfer and second law analyses of forced convection in a channel partially filled by porous media and featuring internal heat sources

This paper provides a comprehensive study on the heat transfer and entropy generation rates in a channel partially filled with a porous medium and under constant wall heat flux. The porous inserts are attached to the walls of the channel and the system features internal heat sources due to exothermic or endothermic physical or physicochemical processes. Darcy-Brinkman model is used for modelling the transport of momentum and an analytical study on the basis of LTNE (local thermal non-equilibrium) condition is conducted. Further analysis through considering the simplifying, LTE (local thermal equilibrium) model is also presented. Analytical solutions are, first, developed for the velocity and temperature fields. These are subsequently incorporated into the fundamental equations of entropy generation and both local and total entropy generation rates are investigated for a number of cases. It is argued that, comparing with LTE, the LTNE approach yields more accurate results on the temperature distribution within the system and therefore reveals more realistic Nusselt number and entropy generation rates. In keeping with the previous investigations, bifurcation phenomena are observed in the temperature field and rates of entropy generation. It is, further, demonstrated that partial filling of the channel leads to a substantial reduction of the total entropy generation. The results also show that the exothermicity or endothermicity characteristics of the system have significant impacts on the temperature fields, Nusselt number and entropy generation rates

A thermodynamic analysis of forced convection through porous media using pore scale modeling

The flow thorough porous media is analyzed from a thermodynamic perspective, with a particular focus on the entropy generation inside the porous media, using a pore scale modeling approach. A single representative elementary volume was utilized to reduce the CPU time. Periodic boundary conditions were employed for the vertical boundaries, by re-injecting the velocity and temperature profiles from the outlet to the inlet and iterating. The entropy generation was determined for both circular and square cross-sectional configurations, and the effects of different Reynolds numbers, assuming Darcy and Forchheimer regimes, were also taken into account. Three porosities were evaluated and discussed for each cross-sectional configuration, and streamlines, isothermal lines and the local entropy generation rate contours were determined and compared. The local entropy generation rate contours indicated that the highest entropy generation regions were close to the inlet for low Reynolds flows and near the central cylinder for high Reynolds flows. Increasing Reynolds number from 100 to 200 reveals disturbances in the dimensionless volume averaged entropy generation rate trend that may be due to a change in the fluid flow regime. According to Bejan number evaluation for both cross-section configurations, it is demonstrated that is mainly provoked by the heat transfer irreversibility. A performance evaluation criterion parameter was calculated for different case-studies. By this parameter, conditions for obtaining the least entropy generation and the highest Nusselt number could be achieved simultaneously. Indeed, this parameter utilizes both the first and the second laws of thermodynamics to present the best case-study. According to the performance evaluation criterion, it is indicated that the square cross-section configuration with o=0.64 exhibits better thermal performance for low Reynolds number flows. A comparison between the equal porosity cases for two different cross-sectional configurations indicated that the square cross-section demonstrated a higher performance evaluation criterion than the circular cross-section, for a variety of different Reynolds numbers

Entropy generation analysisfor the design optimizationof solid oxide fuel cells

Purpose - The aim of this paper is to investigate performance improvements of a monolithic solid oxide fuel cell geometry through an entropy generation analysis. Design/methodology/approach - The analysis of entropy generation rates makes it possible to identify the phenomena that cause the main irreversibilities in the fuel cell, to understand their causes and to propose changes in the design and operation of the system. The various contributions to entropy generation are analyzed separately in order to identify which geometrical parameters should be considered as the independent variables in the optimization procedure. The local entropy generation rates are obtained through 3D numerical calculations, which account for the heat, mass, momentum, species and current transport. The system is then optimized in order to minimize the overall entropy generation and increase efficiency. Findings - In the optimized geometry, the power density is increased by about 10 per cent compared to typical designs. In addition, a 20 per cent reduction in the fuel cell volume can be achieved with less than a 1 per cent reduction in the power density with respect to the optimal design. Research limitations/implications - The physical model is based on a simple composition of the reactants, which also implies that no chemical reactions (water gas shift, methane steam reforming, etc.) take place in the fuel cell. Nevertheless, the entire procedure could be applied in the case of different gas compositions. Practical implications - Entropy generation analysis allows one to identify the geometrical parameters that are expected to play important roles in the optimization process and thus to reduce the free independent variables that have to be considered. This information may also be used for design improvement purposes. Originality/value - In this paper, entropy generation analysis is used for a multi-physics problem that involves various irreversible terms, with the double use of this physical quantity: as a guide to select the most relevant design geometrical quantities to be modified and as objective function to be minimized in the optimization proces

Entropy generation and jet engine optimization

In 2009, it was shown that, with an original approach to hydrodynamic cavitation, a phenomenological model was realized in order to compute some of the physical parameters needed for the design of the most common technological applications (turbo-machinery, etc.) with an economical saving in planning because this analysis could allow engineers to reduce the experimental tests and the consequent costs in the design process. Here the same approach has been used to obtain range of some physical quantity for jet engine optimization

Paths and stochastic order in open systems

The principle of maximum irreversible is proved to be a consequence of a stochastic order of the paths inside the phase space; indeed, the system evolves on the greatest path in the stochastic order. The result obtained is that, at the stability, the entropy generation is maximum and, this maximum value is consequence of the stochastic order of the paths in the phase space, while, conversely, the stochastic order of the paths in the phase space is a consequence of the maximum of the entropy generation at the stability

Entropy Generation in MHD Flow of a Uniformly Stretched Vertical Permeable Surface under Oscillatory Suction Velocity

This paper reports the analytical calculation of the entropy generation due to heat and mass transfer and fluid friction in steady state of a uniformly stretched vertical permeable surface with heat and mass diffusive walls, by solving analytically the mass, momentum, species concentration and energy balance equation, using asymptotic method. The velocity, temperature and concentration profiles were reported and discussed. The influences of the chemical reaction parameter, the thermal and mass Grashof numbers, heat generation/absorption and Hartmann number on total entropy generation were investigated, reported and discussed

Entropy generation in 2+1-dimensional Gravity

The tunneling approach, for entropy generation in quantum gravity, is shown to be valid when applied to 3-D general relativity. The entropy of de Sitter and Reissner-Nordstr\"om external event horizons and of the 3-D black hole obtained by Ba\~nados et. al. is rederived from tunneling of the metric to these spacetimes. The analysis for spacetimes with an external horizon is carried out in a complete analogy with the 4-D case. However, we find significant differences for the black hole. In particular the initial configuration that tunnels to a 3-D black hole may not to yield an infinitely degenerate object, as in 4-D Schwarzschild black hole. We discuss the possible relation to the evaporation of the 3-D black hole.Comment: 22 pages, Tex, TAUP-2102-9

Maximum entropy generation in open systems: the Fourth Law?

This paper develops an analytical and rigorous formulation of the maximum entropy generation principle. The result is suggested as the Fourth Law of Thermodynamics