Low-Cost High-Sensitivity Strain and Temperature Sensing Using Graded-Index Multimode Fibers

We report a low-loss, low-cost high-sensitivity all-fiber strain and temperature sensor based on mode interference in graded-index multimode fibers. Blueshifts with strain and temperature sensitivities of 18.6 pm/microstrain and 58.5 pm/°C have been observed. Experimental results show that smaller core diameter graded-index fibers display greater strain-induced peak wavelength shifts than larger core diameter fibers

Core-Offset Small-Core-Diameter Dispersion Compensation Fiber Interferometer and its Applications in Fiber Sensors

We propose a core-offset small core diameter dispersion compensation fiber (DCF) interferometer and investigate its applications in fiber sensors. If the transverse force is applied to a short section of the DCF, there is almost no crosstalk on the transmission spectrum between the extinction ratio variation induced by the transverse force and the wavelength shift caused by the longitudinal strain or ambient temperature, which can be applied to measure both transverse and longitudinal strain, or both transverse strain and temperature, simultaneously. The proposed sensors have the advantages of low cost, simple and compact structure, and good reproducibility

Development of hot drawing process for nitinol tube

In recent years, Nitinol, near-equiatomic nickel-titanium alloys, have found growing applications in medical technology and joining technology, due to their special characteristics such as shape memory, superplasticity and biocompatibility. The production of Nitinol tube cost-effectively remains a technical challenge. In this paper, we describe a hot drawing process for Nitinol tube production. A Nitinol tube blank and a metal core are assembled together. The assembly is hot drawn for several passes to a final diameter. The metal core is then plastically stretched to reduce its diameter and removed from the tube. Hot drawing process has been applied to Ni50.7Ti and Ni47Ti44Nb9 alloys. Nitinol tubes of 13.6 mm outer diameter and 1 mm wall thickness have been successfully produced from a tube blank of 20 mm outer diameter and 3.5 mm thickness

Magnetization pinning in modulated nanowires: from topological protection to the "corkscrew" mechanism

Diameter-modulated nanowires offer an important paradigm to design the magnetization response of 3D magnetic nanostructures by engineering the domain wall pinning. With the aim to understand its nature and to control the process, we analyze the magnetization response in FeCo modulated polycrystalline two-segment nanowires varying the minor diameter. Our modelling indicates a very complex behavior with a strong dependence on the disorder distribution and an important role of topologically non-trivial magnetization structures. We demonstrate that modulated nanowires with a small diameter difference are characterized by an increased coercive field in comparison to the straight ones which is explained by a formation of topologically protected walls formed by two 3D skyrmions with opposite chiralities. For a large diameter difference we report the occurrence of a novel pinning type called here the "corkscrew": the magnetization of the large diameter segment forms a skyrmion tube with a core position in a helical modulation along the nanowire. This structure is pinned at the constriction and in order to penetrate the narrow segments the vortex/skyrmion core size should be reduced

Passively mode-locked laser using an entirely centred erbium-doped fiber

This paper describes the setup and experimental results for an entirely centred erbium-doped fiber laser with passively mode-locked output. The gain medium of the ring laser cavity configuration comprises a 3 m length of two-core optical fiber, wherein an undoped outer core region of 9.38 μm diameter surrounds a 4.00 μm diameter central core region doped with erbium ions at 400 ppm concentration. The generated stable soliton mode-locking output has a central wavelength of 1533 nm and pulses that yield an average output power of 0.33 mW with a pulse energy of 31.8 pJ. The pulse duration is 0.7 ps and the measured output repetition rate of 10.37 MHz corresponds to a 96.4 ns pulse spacing in the pulse train

Electronic Properties of Strained Si/Ge Core-Shell Nanowires

We investigated the electronic properties of strained Si/Ge core-shell nanowires along the [110] direction using first principles calculations based on density-functional theory. The diameter of the studied core-shell wire is up to 5 nm. We found the band gap of the core-shell wire is smaller than that of both pure Si and Ge wires with the same diameter. This reduced band gap is ascribed to the intrinsic strain between Ge and Si layers, which partially counters the quantum confinement effect. The external strain is further applied to the nanowires for tuning the band structure and band gap. By applying sufficient tensile strain, we found the band gap of Si-core/Ge-shell nanowire with diameter larger than ~3 nm experiences a transition from direct to indirect gap.Comment: 4 figure

Co-axial capillaries microfluidic device for synthesizing size- and morphology-controlled polymer core-polymer shell particles

An easy assembling-disassembling co-axial capillaries microfluidic device was built up for the production of double droplets. Uniform polymer core-polymer shell particles were synthesized by polymerizing the two immiscible monomer phases composing the double droplet. Thus poly(acrylamide) core-poly(tripropylenglycol-diacrylate) shell particles with controlled core diameter and shell thickness were simply obtained by adjusting operating parameters. An empirical law was extracted from experiments to predict core and shell sizes. Additionally uniform and predictable non-spherical polymer objects were also prepared without adding shape-formation procedures in the experimental device. An empirical equation for describing the lengths of rod-like polymer particles is also presented

Allowable silicon wafer thickness versus diameter for ingot rotation ID wafering

Inner diameter (ID) wafering of ingot rotation reduce the ID saw blade diameter was investigated. The blade thickness can be reduced, resulting in minimal kerf loss. However, significant breakage of wafers occurs during the rotation wafering as the wafer thickness decreases. Fracture mechanics was used to develop an equation relating wafer thickness, diameter and fracture behavior at the point of fracture by using a model of a wafer, supported by a center column and subjected to a cantilever force. It is indicated that the minimum allowable wafer thickness does not increase appreciably with increasing wafer diameter and that fracture through the thickness rather than through the center supporting column limits the minimum allowable wafer thickness. It is suggested that the minimum allowable wafer thickness can be reduced by using a vacuum chuck on the wafer surface to enhance cleavage fracture of the center core and by using 111 ingots