Triblock copolyesters derived from lactic acid and glucose: synthesis, nanoparticle formation and simulation

ABA triblock copolyesters were synthesized by ring-opening polymerization (ROP) of l-lactide in solution initiated by a telechelic d-glucose-based polyester macroinitiator. The macroinitiator with a number-average molecular weight about 2500 g mol-1 was synthesized by non-stoichiometric polycondensation in the melt of 2,4:3,5-di-O-methylene-d-glucitol and dimethyl succinate. Two triblock copolyesters of Mn ranging between ~6000 and ~9000 g mol-1, and differing in the length of the polylactide blocks were prepared. These copolyesters started to decompose when heated at ~220 °C and degraded slowly upon aqueous incubation under physiological conditions. They did not display any perceivable crystallinity and showed a single glass transition temperature (Tg) around 60 °C with the higher value corresponding to the larger content in glucitol units. The copolyesters were able to form nanoparticles with average diameters of ~100–130 nm and satisfactory dispersity. The effect of the block lengths on size, ¿-potential values and physical stability of the nanoparticles was evaluated. A molecular dynamics simulation study allowed modelling the two-phase structure of the nanoparticles and evidenced the preference of the glucose-based block to be peripherally located.Peer ReviewedPostprint (author's final draft

Fully bio-based aromatic–aliphatic copolyesters: poly(butylene furandicarboxylate-co-succinate)s obtained by ring opening polymerization

Poly(butylene 2,5-furandicarboxylate-co-succinate) copolyesters (coPBFxSy) have been synthesized by ring opening polymerization (ROP). Cyclic butylene 2,5-furandicarboxylate and butylene succinate oligomer mixtures, to be used as monomers for ROP, were prepared by high dilution condensation and enzymatic cyclization reactions, respectively. Two different catalytic systems, tin dioctanoate and supported Candida antarctica lipase B (CALB), were used for polymerization. Thus two series of copolyesters covering the whole range of compositions were prepared and their properties comparatively examined. In both cases, random copolyesters with compositions close to those used in their respective feeds were obtained. The influence of composition on reaction kinetics with respect to time and temperature was evaluated for the two series. Chemically catalyzed ROP rendered copolyesters with Mw in the ~50 000–65 000 g mol-1 range, whereas values between 15 000 and 45 000 g mol-1 were attained when the ROP reaction was assisted by CALB. The thermal behavior of coPBFxSy obtained by ROP was similar to that reported for such copolymers prepared by melt polycondensation. They all start to decompose above 300 °C and display melting enthalpy and temperatures that decrease with copolymerization, attaining minimum values when the comonomer contents are approximate to balance. On the contrary, the glass-transition temperature increased almost linearly with the content of butylene furandicarboxylate units, covering the whole range of values between those of the two parent homopolyesters. Small deviations in thermal properties observed between the two series could be attributed to their differences in molecular weights. Hydrolytic and enzymatic degradation studies revealed that coPBFxSy became more degradable with increasing content of succinic units, whereas the homopolyester PBF remained practically unaffected when incubated under similar conditions.Peer ReviewedPostprint (author's final draft

Effect of methyl groups on the thermal properties of polyesters from methyl substituted 1,4-butanediols and 4,4'-biphenyldicarboxylic acid

Results are reported on the effect of lateral methyl groups on the thermal properties of a series of polyesters prepared from diethyl 4,4-biphenyldicarboxylate and various methyl substituted 1,4-butanediols. The diols were 1,4-butanediol; 2-methyl-1,4-butanediol; 2,2-dimethyl-1,4-butanediol; 2,3-dimethyl-1,4-butanediol; 2,2,3-trimethyl-1,4-butanediol; and 2,2,3,3-tetramethyl-1,4-butanediol. Apart from the tetramethyl derivatve, the transition temperatures of the methyl substituted polyesters were lower with respect of the unsubstituted polyester. On the basis of polarized photomicrographs, a smectic A mesophase was found for the unsubstituted polyester, whereas a nematic mesophase was observed for the 2-methyl substituted polyster. The 2,2-dimethyl, 2,3-dimethyl, and the 2,2,3-trimethyl substituted polyesters showed no liquid crystalline behavior. The 2,2,3,3-tetramethyl derivative displayed a birefringent melt phase although the DSC measurements were not unambiguous. A copolyester based on diethyl 4,4-biphenyldicarboxylate, 1,4-butanediol, and 2,2,3,3-tetramethyl-1,4-butanediol showed a broad nematic mesophase. Further evidence for the nematic mesophase of this copolyester and the 2-methyl substituted polyester was provided by dynamic rheological experiments. Based on thermogravimetric analysis, it was concluded that the thermal stability was affected only when four methyl side groups were present in the spacer

Testing of molded high temperature plastic actuator road seals for use in advanced aircraft hydraulic systems

Molded high temperature plastic first and second stage rod seal elements were evaluated in seal assemblies to determine performance characteristics. These characteristics were compared with the performance of machined seal elements. The 6.35 cm second stage Chevron seal assembly was tested using molded Chevrons fabricated from five molding materials. Impulse screening tests conducted over a range of 311 K to 478 K revealed thermal setting deficiencies in the aromatic polyimide molding materials. Seal elements fabricated from aromatic copolyester materials structurally failed during impulse cycle calibration. Endurance testing of 3.85 million cycles at 450 K using MIL-H-83283 fluid showed poorer seal performance with the unfilled aromatic polyimide material than had been attained with seals machined from Vespel SP-21 material. The 6.35 cm first stage step-cut compression loaded seal ring fabricated from copolyester injection molding material failed structurally during impulse cycle calibration. Molding of complex shape rod seals was shown to be a potentially controllable technique, but additional molding material property testing is recommended

Pivalolactone, 2. Copolyester synthesis via interchange reactions with polypivalolactone

The synthesis of copolyesters via interchange reactions of polypivalolactone (PPVL) with several compounds was studied. The synthetical procedures are two-stage melt processes: in the first stage ester bonds in the polymer chain are cleaved and new groups are incorporated in the polymer chain, while in the second step condensation of the end-groups formed occurs. For the synthesis of copolymers, three procedures were used, with tetrabutyl orthotitanate as a catalyst. PPVL was heated with equimolar mixtures of bisphenol-A diacetate (BPAac) and terephthalic acid (TA), but no copolymers were formed; instead, polycondensation of BPAac with TA occurred, leaving the PPVL unaffected. From PPVL and mixtures of BPAac and dimethyl terephthalate (DMT) polymers were obtained which contained a significant amount of copolymeric sequences. However, most of the polymeric chains consisted of PPVL and poly(bisphenol-A terephthalate) blocks. Random copolymers with thermal stability were obtained after heating PPVL with bisphenol-A polycarbonate and DMT. The latter process was studied in detail by IR, DSC, and solubility and selective degradation tests. Based on the results of these studies, the reactions occurring during the three procedures were discussed

Controlling the isothermal crystallization of isodimorphic PBS-ran-PCL random copolymers by varying composition and supercooling

In this work, we study for the first time, the isothermal crystallization behavior of isodimorphic random poly(butylene succinate)-ran-poly(e-caprolactone) copolyesters, PBS-ran-PCL, previously synthesized by us. We perform nucleation and spherulitic growth kinetics by polarized light optical microscopy (PLOM) and overall isothermal crystallization kinetics by differential scanning calorimetry (DSC). Selected samples were also studied by real-time wide angle X-ray diffraction (WAXS). Under isothermal conditions, only the PBS-rich phase or the PCL-rich phase could crystallize as long as the composition was away from the pseudo-eutectic point. In comparison with the parent homopolymers, as comonomer content increased, both PBS-rich and PCL-rich phases nucleated much faster, but their spherulitic growth rates were much slower. Therefore, the overall crystallization kinetics was a strong function of composition and supercooling. The only copolymer with the eutectic composition exhibited a remarkable behavior. By tuning the crystallization temperature, this copolyester could form either a single crystalline phase or both phases, with remarkably different thermal propertiesPeer ReviewedPostprint (published version

Effect of hydroxyapatite nanoparticles on the degradability of random poly(butylene terephthalate-co-aliphatic dicarboxylate)s having a high content of terephthalic units

Copolyesters derived from 1,4-butanediol and constituted also of aliphatic and aromatic dicarboxylate units in a molar ratio of 3:7 were synthesized by a two-step polycondensation procedure. Succinic, adipic, and sebacic acids were specifically selected as the aliphatic component whereas terephthalic acid was chosen as the aromatic moiety. The second synthesis step was a thermal transesterification between the corresponding homopolymers, always attaining a random distribution as verified by NMR spectroscopy. Hybrid polymer composites containing 2.5 wt % of hydroxyapatite (HAp) were also prepared by in situ polymerization. Hydroxyl groups on the nanoparticle surface allowed the grafting of polymer chains in such a way that composites were mostly insoluble in the typical solvents of the parent copolyesters. HAp had some influence on crystallization from the melt, thermal stability, and mechanical properties. HAp also improved the biocompatibility of samples due to the presence of Ca2+ cations and the damping effect of phosphate groups. Interestingly, HAp resulted in a significant increase in the hydrophilicity of samples, which considerably affected both enzymatic and hydrolytic degradability. Slight differences were also found in the function of the dicarboxylic component, as the lowest degradation rates was found for the sample constituted of the most hydrophobic sebacic acid units. View Full-TextPeer ReviewedPostprint (published version

Nonelastomeric Rod Seals for Advanced Hydraulic Systems

Advanced high temperature hydraulic system rod sealing requirements can be met by using seals made of nonelastomeric (plastic) materials in applications where elastomers do not have adequate life. Exploratory seal designs were optimized for advanced applications using machinable polyimide materials. These seals demonstrated equivalent flight hour lives of 12,500 at 350 F and 9,875 at 400 F in advanced hydraulic system simulation. Successful operation was also attained under simulated space shuttle applications; 96 reentry thermal cycles and 1,438 hours of vacuum storage. Tests of less expensive molded plastic seals indicated a need for improved materials to provide equivalent performance to the machined seals

Poly(butylene succinate) ionomers with enhanced hydrodegradability

A series of poly(butylene succinate) (PBS) ionomers containing up to 14 mol%of sulfonated succinate units have been synthesized by polycondensation in the melt-phase. The copolyesters were obtained with weight average molecular weights oscillating between 33,000 and 72,000 g·mol-1. All copolyesters were semicrystalline with melting temperatures and enthalpies decreasing and glass transition temperatures increasing with the content of ionic units. The thermal stability of PBS was slightly reduced by the incorporation of these units, and it was also found that the copolyesters were stiffer but also more brittle than PBS. The hydrolytic degradability of PBS was enhanced by copolymerization, an effect that was much more pronounced in basic media.Peer ReviewedPostprint (published version

Chemical recycling of poly(ethylene terephthalate). Application to the synthesis of multiblock copolyesters

The chemical recycling of the poly(ethylene terephthalate), (PET), has been successfully carried out by glycolysis in the presence of bis (2-hydroxyethyl) terephthalate (BHET) resulting in the formation of hydroxytelechelic oligomers. These oligomers were then treated with carboxytelechelic poly(ε-caprolactone) oligomers of Mn = 2300 and Mn = 730 g•mol–1 molecular weight, in the absence or presence of the titanium tetrabutyloxide (Ti(OBu)4) as a catalyst to get multiblock copolyesters. The chemical structure of the synthesized copolyesters was investigated by size exclusion chromatography (SEC) and proton Nuclear Magnetic Resonance (1H NMR) spectroscopy. Moreover the differential scanning calorimetry (DSC) was used to explore their thermal properties. The ester-ester interchange reaction was observed between the two oligopolyesters, was studied and discussed in detail