Polymer Micro/Nanofibre Waveguides for Optical Sensing Applications

This chapter focuses on polymer micro/nanofibre (PMNFs) waveguides and their applications in sensing applications. The PMNFs are functionalized by doping with dyes or blending with solvated polymers before the drawing process. Based on the evanescent wave-coupling technique, the excitation light is efficiently coupled into the PMNFs using silica-fibre tapers and guided along the long-length PMNF waveguides. Due to the tight confinement, the interaction of light with PMNFs is significantly enhanced. Intriguing advantages such as enhanced excitation efficiency, low excitation power operation and high photostability are obtained. On the basis of the optical response when exposed to specimens, functionalized PMNFs are used for humidity, NO2, and NH3 detection with high sensitivity and fast response. By using a simple and low-cost nanoimprinting technique, PMNF Bragg gratings are also demonstrated for strain sensing with a high sensitivity of −2.5 pm/με

Distribution of polycyclic aromatic hydrocarbons in subcellular root tissues of ryegrass (Lolium multiflorum Lam.)

BACKGROUND: Because of the increasing quantity and high toxicity to humans of polycyclic aromatic hydrocarbons (PAHs) in the environment, several bioremediation mechanisms and protocols have been investigated to restore PAH-contaminated sites. The transport of organic contaminants among plant cells via tissues and their partition in roots, stalks, and leaves resulting from transpiration and lipid content have been extensively investigated. However, information about PAH distributions in intracellular tissues is lacking, thus limiting the further development of a mechanism-based phytoremediation strategy to improve treatment efficiency. RESULTS: Pyrene exhibited higher uptake and was more recalcitrant to metabolism in ryegrass roots than was phenanthrene. The kinetic processes of uptake from ryegrass culture medium revealed that these two PAHs were first adsorbed onto root cell walls, and they then penetrated cell membranes and were distributed in intracellular organelle fractions. At the beginning of uptake (< 50 h), adsorption to cell walls dominated the subcellular partitioning of the PAHs. After 96 h of uptake, the subcellular partition of PAHs approached a stable state in the plant water system, with the proportion of PAH distributed in subcellular fractions being controlled by the lipid contents of each component. Phenanthrene and pyrene primarily accumulated in plant root cell walls and organelles, with about 45% of PAHs in each of these two fractions, and the remainder was retained in the dissolved fraction of the cells. Because of its higher lipophilicity, pyrene displayed greater accumulation factors in subcellular walls and organelle fractions than did phenanthrene. CONCLUSIONS: Transpiration and the lipid content of root cell fractions are the main drivers of the subcellular partition of PAHs in roots. Initially, PAHs adsorb to plant cell walls, and they then gradually diffuse into subcellular fractions of tissues. The lipid content of intracellular components determines the accumulation of lipophilic compounds, and the diffusion rate is related to the concentration gradient established between cell walls and cell organelles. Our results offer insights into the transport mechanisms of PAHs in ryegrass roots and their diffusion in root cells

Well-dispersed sulfur anchored on interconnected polypyrrole nanofiber network as high performance cathode for lithium-sulfur batteries

Abstract Preparation of novel sulfur/polypyrrole (S/PPy) composite consisting well-dispersed sulfur particles anchored on interconnected PPy nanowire network was demonstrated. In such hybrid structure, the as-prepared PPy clearly displays a three-dimensionally cross-linked and hierarchical porous structure, which was utilized in the composite cathode as a conductive network trapping soluble polysulfide intermediates and enhancing the overall electrochemical performance of the system. Benefiting from this unique structure, the S/PPy composite demonstrated excellent cycling stability, resulting in a discharge capacity of 931 mAh g−1 at the second cycle and retained about 54% of this value over 100 cycles at 0.1 C. Furthermore, the S/PPy composite cathode exhibits a good rate capability with a discharge capacity of 584 mAh g−1 at 1  C

Predictors of Gull-billed tern (Gelochelidon nilotica) nest survival in artificial coastal saltpans, Bohai Bay, China

Background Coastal saltpans are a common supratidal human-modified wetland habitat found within many coastal landscape mosaics. Commercial salt production and aquaculture practices often result in the creation of exposed coastal substrates that could provide suitable breeding habitat for waterbird populations; however, few studies have quantified waterbird breeding success in these artificial wetlands. Methods Here we examine the nesting behavior of the Gull-billed tern (Gelochelidon nilotica) breeding in the Nanpu coastal saltpans of Bohai Bay, Yellow Sea, China over three consecutive nesting seasons (2017–2019) by using nest survival model in Program MARK. Results The results revealed that nest survival of Gull-billed terns in coastal saltpans (0.697) was higher than previously published estimates from other regions, with an estimated daily survival rate (DSR) of 0.982 ± 0.001 (±95% CI). High nest survival was mainly attributed to low levels of human disturbances and low predation rates, while exposure to strong winds, flooding and silting were the main factors causing nest failure. Model-averaged estimates revealed that eggs laid in nests located on ‘habitat islands’ with feather or clam shell substrates were most likely to hatch. Initiation date, nest age, clutch size and quadratic effects of nearest-neighbor distance, nearest distance to road and nearest distance to water were all significant predictors of nest success, but the nest survival declined overall from 2017 to 2019 due to the degradation and loss of breeding habitat anthropogenically caused by rising water levels. Discussion Coastal saltpans represent an alternative breeding habitat for the Gull-billed tern populations in Bohai Bay, but conservation management should prioritize flood prevention to improve the extent and quality of breeding habitat, concurrent with efforts to create further ‘habitat islands’ with suitable nesting substrate

Calcium–magnesium–alumina–silicate (CMAS) resistance of LaPO4 thermal barrier coatings

Nanostructured LaPO4 thermal barrier coatings (TBCs) were prepared by air plasma spraying, and their resistance to calcium–magnesium–alumina–silicate (CMAS) attack at 1250 °C, 1300 °C and 1350 °C was investigated. The reaction products were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy and transmission electron microscopy. Exposed to CMAS attack for 0.5 h, a continuous dense reaction layer formed, which was mainly composed of P–Si apatite based on Ca2+xLa8-x(PO4)x(SiO4)6-xO2, anorthite and spinel phases. Beneath the reaction layer, little evidence of CMAS trace could be found. With the increase in temperature and heat treatment duration, the reaction layer became thick, while penetration depth of the molten CMAS changed slightly. Due to the formation of a reaction layer suppressing CMAS further infiltration, LaPO4 TBCs are highly resistant to CMAS attack

Simple One-Pot Synthesis of Hexagonal ZnO Nanoplates as Anode Material for Lithium-Ion Batteries

Hexagonal ZnO nanoplates were synthesized via simple one-pot hydrothermal reaction of Zn(CH3COO)2 and CO(NH2)2. XRD, SEM, and HRTEM were used to investigate the composition and microstructure of the material. Together with the facile strain relaxation during structure and volume change upon cycling, this plate-like structure of ZnO is favorable for physical and chemical interactions with lithium ions because of its large contact area with the electrolyte, providing more active sites and short diffusion distances. The resulting hexagonal ZnO nanoplates electrode exhibited good cyclability and delivered a reversible discharge capacity of 368 mAh g−1 after 100 cycles at 0.1 C

Audio is all in one: speech-driven gesture synthetics using WavLM pre-trained model

The generation of co-speech gestures for digital humans is an emerging area in the field of virtual human creation. Prior research has made progress by using acoustic and semantic information as input and adopting classify method to identify the person's ID and emotion for driving co-speech gesture generation. However, this endeavour still faces significant challenges. These challenges go beyond the intricate interplay between co-speech gestures, speech acoustic, and semantics; they also encompass the complexities associated with personality, emotion, and other obscure but important factors. This paper introduces "diffmotion-v2," a speech-conditional diffusion-based and non-autoregressive transformer-based generative model with WavLM pre-trained model. It can produce individual and stylized full-body co-speech gestures only using raw speech audio, eliminating the need for complex multimodal processing and manually annotated. Firstly, considering that speech audio not only contains acoustic and semantic features but also conveys personality traits, emotions, and more subtle information related to accompanying gestures, we pioneer the adaptation of WavLM, a large-scale pre-trained model, to extract low-level and high-level audio information. Secondly, we introduce an adaptive layer norm architecture in the transformer-based layer to learn the relationship between speech information and accompanying gestures. Extensive subjective evaluation experiments are conducted on the Trinity, ZEGGS, and BEAT datasets to confirm the WavLM and the model's ability to synthesize natural co-speech gestures with various styles.Comment: 10 pages, 5 figures, 1 tabl

Synthesis and Characterization of Nanostructured WC-Co/Al Powder Prepared by Mechanical Alloying

Nanostructured WC-Co/Al powder was synthesized from WC-12Co powder and pure Al powder by mechanical alloying (MA). The morphology and microstructural evolution of WC-Co/Al powder were investigated by a series of characterization methods. The results showed that the β-Co phase in the initial WC-12Co powder was replaced by the AlxCo phases (such as Al9Co2 and Al13Co4). As the ball milling time increased, the average grain size of WC in the WC-Co/Al powder decreased firstly and then remained at a constant value of around 40 nm. The deposition behavior of powders sprayed by high velocity oxygen fuel (HVOF) spraying was investigated. During spraying, the WC-Co/Al powder had a better flattening than the WC-12Co powder without ball milling, which is beneficial to fabricate compact coatings with lower porosity

Synthesis of hierarchical MoS2 microspheres composed of nanosheets assembled via facile hydrothermal method as anode material for lithium-ion batteries

A hierarchical MoS2 architecture composed of nanosheet-assembled microspheres with an expanded interplanar spacing of the (002) planes was successfully prepared via a simple hydrothermal reaction. Electron microscopy studies revealed formation of the MoS2 microspheres with an average diameter of 230 nm. It was shown that the hierarchical structure of MoS2 microspheres possesses both the merits of nanometer-sized building blocks and micrometer-sized assemblies, which offer high surface area for fast kinetics and buffers the volume expansion during lithium insertion/deinsertion, respectively. The micrometer-sized assemblies were found to contribute to the enhanced electrochemical stabilities of the electrode materials...