Oxide Free Wire Arc Sprayed Coatings—An Avenue to Enhanced Adhesive Tensile Strength

Conventionally, thermal spraying processes are almost exclusively carried out in an air atmosphere. This results in oxidation of the particles upon thermal spraying, and thus, the interfaces of the splats within the coating are oxidized as well. Hence, a full material bond strength cannot be established. To overcome this issue, a mixture of monosilane and nitrogen was employed in the present study as the atomising and environment gas. With this approach, an oxygen partial pressure corresponding to an extreme-high vacuum was established in the environment and oxide-free coatings could be realized. It is shown that the oxide-free particles have an improved substrate wetting behaviour, which drastically increases the adhesive tensile strength of the wire arc sprayed copper coatings. Moreover, the altered deposition conditions also led to a significant reduction of the coating porosity

Gas Phase Reaction of Silane with Water at Different Temperatures and Supported by Plasma

The interaction of silane and water is discussed controversially in literature: some authors suggest monosilane and water react kinetically and sufficiently fast enough to remove water, while others state the reaction occurs only at elevated temperatures. This question is of technological interest for the removal of unavoidable water residues in Ar gases. Thermodynamic calculations show that virtually complete removal of water is expected with superstoichiometric silane addition. However, mass spectrometric and infrared spectroscopic experiments give evidence that the addition of monosilane to such an Ar gas at room temperature is unable to remove residual water, which disagrees with some current hypotheses in the literature. This holds even for very high SiH4 concentrations up to 2 vol.-%. Silane reacts with water above temperatures of 555 °C, initiated by the thermal decomposition of silane. A cold dielectric barrier discharge-plasma used for silane and water dissociation enhances reactivity similar to elevated temperatures. Fourier-transformed infrared spectroscopy points toward silanol generation at temperatures between 400 and 550 °C, while quadrupole mass spectrometry indicates the creation of SiOH+, SiHOH+, SiH2OH+, and SiH3OH+. Cold plasmas generate smaller amounts of SiOH+, SiHOH+, and SiH2OH+ compared to elevated temperatures. Reaction products are hydrogen and nanoscaled particles of non-stoichiometric silicon oxides. The silicon-oxide particles produced differ in elemental composition and shape depending on the prevailing water content during decomposition: SiOx generated with residual water appears with relatively smooth surfaces, while the addition of water supports the formation of significantly rougher particle surfaces. Higher initial water contents correlate with higher oxygen contents of the particles

Influence of an oxygen-free atmosphere on laser beam brazing of aluminium with prior surface deoxidation by pulsed laser radiation

Aluminium alloys, like AlMgSi1 and AlMg3, cannot be joined in industrial processes by laser beam brazing without the use of fluxes due to their resistant oxide layer. The aim of this study is to dispense with the use of flux. For the investigations, an oxygen-free atmosphere was created by using the highly reactive gas monosilane and thus achieving O2 partial pressures of 10-18 mbar. After removal of the oxides by a laser source with 1064 nm wavelength, pulse energies of max. 0.3 µJ and pulse durations of 45 ns, reoxidation is prevented by the oxygen-free atmosphere, so that brazing is carried out on an oxide-free material surface. The bead on plate seams show a materially bonded brazed joint in cross-section. Reference experiments without monosilane either show no wetting or an increased melting of base material. The influence of laser beam power for brazing, pulse energy for deoxidation and wire feed was investigated

Young’s Modulus and Residual Stresses of Oxide-Free Wire Arc Sprayed Copper Coatings

Conventional thermal spraying processes are almost exclusively carried out in an air atmosphere, resulting in the oxidation of the particle surfaces and interfaces within the coating and between the substrate and coating. Furthermore, the initial process of surface activation conventionally takes place in an air atmosphere, preventing an oxide-free interfacial transition. Consequently, the application of spraying materials with high oxygen affinity represents a major challenge. To overcome these issues, the present study utilized silane-doped inert gases to create an environment in which the oxygen concentration was equivalent to the residual oxygen content in an extreme high vacuum. By transferring the corundum blasting and coating process (wire arc spraying) to this environment, materials with a high oxygen affinity can be applied without oxidation occurring. For industrial use, this is an interesting prospect, e.g., for repair coatings, as the homogeneity of the composite is improved by a non-oxidized coating. Using the example of arc-sprayed copper coatings, the microstructure and mechanical properties of the coatings were analysed. The results showed that the oxide-free, wire arc sprayed copper coatings exhibited an improved wetting behaviour resulting in a significant reduction of the coating porosity. Moreover, the improved wetting behaviour and led to an increase in the bonding rate and apparent Young’s modulus. Contrary to expectations, the residual stresses decrease although relaxation mechanisms should be inhibited, and possible reasons for this are discussed in the paper

Oxide Free Wire Arc Sprayed Coatings—An Avenue to Enhanced Adhesive Tensile Strength

Conventionally, thermal spraying processes are almost exclusively carried out in an air atmosphere. This results in oxidation of the particles upon thermal spraying, and thus, the interfaces of the splats within the coating are oxidized as well. Hence, a full material bond strength cannot be established. To overcome this issue, a mixture of monosilane and nitrogen was employed in the present study as the atomising and environment gas. With this approach, an oxygen partial pressure corresponding to an extreme-high vacuum was established in the environment and oxide-free coatings could be realized. It is shown that the oxide-free particles have an improved substrate wetting behaviour, which drastically increases the adhesive tensile strength of the wire arc sprayed copper coatings. Moreover, the altered deposition conditions also led to a significant reduction of the coating porosity

Oxide Free Wire Arc Sprayed Coatings—An Avenue to Enhanced Adhesive Tensile Strength

Conventionally, thermal spraying processes are almost exclusively carried out in an air atmosphere. This results in oxidation of the particles upon thermal spraying, and thus, the interfaces of the splats within the coating are oxidized as well. Hence, a full material bond strength cannot be established. To overcome this issue, a mixture of monosilane and nitrogen was employed in the present study as the atomising and environment gas. With this approach, an oxygen partial pressure corresponding to an extreme-high vacuum was established in the environment and oxide-free coatings could be realized. It is shown that the oxide-free particles have an improved substrate wetting behaviour, which drastically increases the adhesive tensile strength of the wire arc sprayed copper coatings. Moreover, the altered deposition conditions also led to a significant reduction of the coating porosity