3,508 research outputs found
NASA Quiet Clean General Aviation Turbofan (QCGAT) program status
The suitability of large engine technology to reduce noise, emissions, and fuel consumption of small turbine engines and develop new technology where required is determined. The design, fabrication, assembly, test, and delivery of the experimental engines to NASA are discussed
Preliminary QCGAT program test results
NASA Lewis Research Center is conducting a program to demonstrate that large commercial engine technology can be applied to general aviation engines to reduce noise, emissions and fuel consumption and to develop new technology where required. The overall engine program, design, and technology incorporated into the QCGAT engines are described. In addition, preliminary engine test results are presented and compared to the technical requirements the engines were designed to meet
Microanalytical identification of barium sulphate crystals in statoliths of Chara Rhizoids
In contrast to higher plants, Chara rhizoids contain statolith vacuoles filled with biocrystallites of BaS04 in the form of rods composed of globular subunits ca. 7 nm in diameter. The revelation of the crystallites under electron microscopy is dependent on the fixative; best structural preservation was observed after fixation in a buffered glutaraldehyde + acrolein solution; 0s04 and KMnO4 partially dissolved both the biocrystallites and synthetic BaS04
Summary of NASA QCGAT program
The application of large turbofan engine technology to small general aviation turbofan engines to achieve low noise, low emissions, and acceptable fuel consumption is described
Insect (Arthropoda: Insecta) Composition in the Diet of Ornate Box Turtles (Terrapene ornata ornata) in Two Western Illinois Sand Prairies, with a New State Record for Cyclocephala (Coleoptera: Scarabaeidae)
A study of fecal samples collected over a two-year period from juvenile ornate box turtles (Terrapene ornata ornata Agassiz) revealed diets consisting of six orders of insects representing 19 families. Turtles were reared in captivity from eggs harvested from local, wild populations, and released at two remnant prairies. Identifiable insect fragments were found in 94% of samples in 2013 (n=33) and 96% in 2014 (n=25). Frequency of occurrence of insects in turtle feces is similar to results reported in previous studies of midwestern Terrapene species. A comparison of insect composition presented no significant difference between release sites. There is no significant difference in consumed insect species between turtles released into or outside of a fenced enclosure at the same site. Specimens of Cyclocephala longula LeConte collected during this study represent a new state record for Illinois
Experimentally observed evolution between dynamic patterns and intrinsic localized modes in a driven nonlinear electrical cyclic lattice
Locked intrinsic localized modes (ILMs) and large amplitude lattice spatial
modes (LSMs) have been experimentally measured for a driven 1-D nonlinear
cyclic electric transmission line, where the nonlinear element is a saturable
capacitor. Depending on the number of cells and electrical lattice damping a
LSM of fixed shape can be tuned across the modal spectrum. Interestingly, by
tuning the driver frequency away from this spectrum an LSM can be continuously
converted into ILMs and visa versa. The differences in pattern formation
between simulations and experimental findings are due to a low concentration of
impurities. Through this novel nonlinear excitation and switching channel in
cyclic lattices either energy balanced or unbalanced LSMs and ILMs may occur.
Because of the general nature of these dynamical results for nonintegrable
lattices applications are to be expected. The ultimate stability of driven aero
machinery containing nonlinear periodic structures may be one example.Comment: 7 pages 7 figure
International Space Station Powered Bolt Nut Anomaly and Failure Analysis Summary
A key mechanism used in the on-orbit assembly of the International Space Station (ISS) pressurized elements is the Common Berthing Mechanism (CBM). The mechanism that effects the structural connection of the CBM halves is the Powered Bolt Assembly. There are sixteen Powered Bolt Assemblies per CBM. The CBM has a bolt which engages a self aligning Powered Bolt Nut (PBN) on the mating interface; see Figure 1. The Powered Bolt Assemblies are preloaded to approximately 19 kilo pounds (KIPs) prior to pressurization of the CBM. The PBNs mentioned below, manufactured in 2009, will be used on ISS future missions. An on orbit functional failure of this hardware would be unacceptable and in some instances catastrophic due to the failure of modules to mate and seal the atmosphere, risking loss of crew and ISS functions. The manufacturing processes which create the PBNs need to be strictly controlled. Functional (torque vs. tension) acceptance test failures will be the result of processes not being strictly followed. Without the proper knowledge of thread tolerances, fabrication techniques, and dry film lubricant application processes, PBNs will be, and have been manufactured improperly. The knowledge gained from acceptance test failures and the resolution of those failures, thread fabrication techniques and thread dry film lubrication processes can be applied to many aerospace mechanisms to enhance their performance. Test data and manufactured PBN thread geometry will be discussed for both failed and successfully accepted PBNs
Fuel savings potential of the NASA Advanced Turboprop Program
The NASA Advanced Turboprop (ATP) Program is directed at developing new technology for highly loaded, multibladed propellers for use at Mach 0.65 to 0.85 and at altitudes compatible with the air transport system requirements. Advanced turboprop engines offer the potential of 15 to 30 percent savings in aircraft block fuel relative to advanced turbofan engines (50 to 60 percent savings over today's turbofan fleet). The concept, propulsive efficiency gains, block fuel savings and other benefits, and the program objectives through a systems approach are described. Current program status and major accomplishments in both single rotation and counter rotation propeller technology are addressed. The overall program from scale model wind tunnel tests to large scale flight tests on testbed aircraft is discussed
Acoustic breathers in two-dimensional lattices
The existence of breathers (time-periodic and spatially localized lattice
vibrations) is well established for i) systems without acoustic phonon branches
and ii) systems with acoustic phonons, but also with additional symmetries
preventing the occurence of strains (dc terms) in the breather solution. The
case of coexistence of strains and acoustic phonon branches is solved (for
simple models) only for one-dimensional lattices.
We calculate breather solutions for a two-dimensional lattice with one
acoustic phonon branch. We start from the easy-to-handle case of a system with
homogeneous (anharmonic) interaction potentials. We then easily continue the
zero-strain breather solution into the model sector with additional quadratic
and cubic potential terms with the help of a generalized Newton method. The
lattice size is . The breather continues to exist, but is dressed
with a strain field. In contrast to the ac breather components, which decay
exponentially in space, the strain field (which has dipole symmetry) should
decay like . On our rather small lattice we find an exponent
Modeling of Remote Condensing AMTEC Cells
The Alkali Metal Thermal to Electric Converter (AMTEC) is a thermally regenerated sodium concentration cell that converts heat directly into electricity without moving parts. The high efficiency of AMTEC cells is useful for power generation in space and terrestrial applications (Ivanenok et al. 1993a, 1993b). One of the advanced features proposed in current high efficiency AMTEC cell designs is remote condensing. Remote condensing occurs when the condensing surface of the cell is thermally isolated from the high temperature β“ ‐alumina solid electrolyte (BASE) tube. The parasitic heat losses are significantly reduced, thereby improving the cell efficiency. However, this configuration also increases the local Na vapor pressure (sodium concentration) on the cathode side of the BASE tube, and thus lowers the BASE tube's power output. The balance of these opposing effects is very important in optimizing system designs. This paper derives the equations necessary to calculate the vapor flow pressure drop, and compares the calculations to experimental data.Peer Reviewedhttp://deepblue.lib.umich.edu/bitstream/2027.42/87617/2/1501_1.pd
- …