40 research outputs found
Recommended from our members
Development of NMRI spectroscopy for improved petroleum recovery, Annex 6. Annual report, 1991
The overall objectives are to develop and apply Nuclear Magnetic Resonance Imaging (NMRI) and CT X-Ray Scanning methods for determining rock, fluid, and petrophysical properties and for fundamental studies of multiphase flow behavior in porous media. Specific objectives are to: (1) develop NMRI procedures for measuring porosity, permeability, pore size distribution, capillary pressure, and wetting characteristics, (2) apply imaging methods for improved methods of determining two- and three-phase relative permeability functions, (3) apply NMRI for development of a better understanding of dispersed phase displacement processes, and (4) apply imaging methods to develop a better understanding of saturation distribution and fingering during miscible displacements. The objectives have been organized into four subtasks. Annual progress reports for each subtask are provided
First measurement of electron neutrino appearance in NOvA
We report results from the first search for νμ→νe transitions by the NOvA experiment. In an exposure equivalent to 2.74×1020 protons on target in the upgraded NuMI beam at Fermilab, we observe 6 events in the Far Detector, compared to a background expectation of 0.99±0.11(syst) events based on the Near Detector measurement. A secondary analysis observes 11 events with a background of 1.07±0.14(syst). The 3.3σ excess of events observed in the primary analysis disfavors 0.1π<δCP<0.5π in the inverted mass hierarchy at the 90% C.L
First measurement of muon-neutrino disappearance in NOvA
This paper reports the first measurement using the NOvA detectors of νμ disappearance in a νμ beam. The analysis uses a 14 kton-equivalent exposure of 2.74×1020 protons-on-target from the Fermilab NuMI beam. Assuming the normal neutrino mass hierarchy, we measure Δm232=(2.52+0.20−0.18)×10−3 eV2 and sin2θ23 in the range 0.38–0.65, both at the 68% confidence level, with two statistically degenerate best-fit points at sin2θ23=0.43 and 0.60. Results for the inverted mass hierarchy are also presented
Structure optimization of PCL foams by using mixtures of CO2 and N2 as blowing agents
The foaming process of poly(e-caprolactone) (PCL) with carbon dioxide and nitrogen was investigated from theor. and exptl. view points. CO2 and N2 showed very different behavior, as foaming agents for PCL. This was due to the different transport, chem., and phys. properties of the polymer/gas mixt. that led to different foam morphol. in terms of d., cell no. d., and cell size. The lowest d. (0.03 g/cm3) was obtained with CO2, but the highest no. of cells with N2 Vectra B 950although with a higher d., (0.2 g/cm3). Foam with a low-d. microcellular structure, was obtained when a mixt. of the two gases was employed
Recommended from our members
Development of asphalts and pavements using recycled tire rubber. Phase 1, Technical feasibility. Technical progress report, September 1, 1994--August 31, 1995
About 285 million tires are discarded every year; less than 100 million are currently being recycled, with the rest being placed in landfills and other waste sites. A solution to reduce the littering of the environment is to use ground tire rubber in road construction. Currently, about 27 million tons of asphalt are used each year in road construction and maintenance of the country`s 2 million miles of roads. If all of the waste tire rubber could be combined with asphalt in road construction, it would displace less than 6% of the total asphalt used each year, yet could save about 60 trillion Btus annually. Purpose of this project is to provide data needed to optimize the performance of rubber-asphalt concretes. The first phase is to develop asphalts and recycling agents tailored for compatibility with ground tire rubber. Chapter 2 presents results on Laboratory Testing and Evaluation: fractionate asphalt material, reblending for aromatic asphalts, verifying optimal curing parameters, aging of blends, and measuring ductilities of asphalt-rubber binders. Chapter 3 focuses on Evaluating Mixture Characteristics (modified binders). Chapter 4 covers Adhesion Test Development (water susceptibility is also covered). The final chapter focuses on the Performance/Economic Update and Commercialization Plan