Cost-effective 3D documentation device in forensic medicine

3D documentation in forensics and forensic medicine is being introduced more frequently in various institutes around the world. However, several institutes lack capacity in finances as well as staff to perform 3D documentations regularly. This technical paper aims to present a 3D documentation device that is low cost and easy to use and is a viable entry level solution for forensic medical departments. For this the small single-board computer Raspberry Pi 4 was used in conjunction with its high quality (HQ) camera module to create the 3DLamp - a flexible, low cost and easy to use documentation device. Besides a detailed description of the device this paper also presents four case examples where a 3D documentation was performed and analyses the acquired data and the created 3D models. It was found that the device returns feasible 3D models that appear usable for forensic 3D reconstructions

Technical note: Semiautomated targeted postmortem computed tomography angiography of the pulmonary arteries using a robotic system

INTRODUCTION To better depict vascular lesions on postmortem computed tomography (PMCT), whole-body postmortem computed tomography angiography (PMCTA) can be used in forensic diagnostics. Targeted angiography, in which only a specific vessel is filled with contrast agent, might help in cases of traumatic changes that render whole-body PMCTA impossible. Moreover, in targeted PMCTA, the contrast agent does not affect the haptics of any other organs. In this article, we describe automated, CT-guided targeted angiography of the pulmonary artery (PA) using the Virtobot system. MATERIAL AND METHODS Our study group consisted of 8 deceased persons (3 males, 5 females). We first performed an unenhanced CT scan and used the data obtained to plan the needle trajectories with the Virtobot planning software. Then, the needle was fully automatically placed by the Virtobot system. Subsequently, 50 ml of contrast agent was injected manually, and the CT scan was repeated (targeted PMCTA). RESULTS AND DISCUSSION We tested a new method for performing semiautomated targeted postmortem angiography of the PAs using a robotic needle placement system (Virtobot). In 6 out of our 8 cases, the injection of contrast agent in the PA was successful. In five of the six successful cases, there was reflux of contrast agent to some extent, but the reflux did not affect the readout. In general, the procedure was easy to plan based on a PMCT data set, and the pulmonary trunk was easy to reach with a robotic needle placement system

Virtobot 2.0: the future of automated surface documentation and CT-guided needle placement in forensic medicine

In this paper we present the second prototype of a robotic system to be used in forensic medicine. The system is capable of performing automated surface documentation using photogrammetry, optical surface scanning and image-guided, post-mortem needle placement for tissue sampling, liquid sampling, or the placement of guide wires. The upgraded system includes workflow optimizations, an automatic tool-change mechanism, a new software module for trajectory planning and a fully automatic computed tomography-data-set registration algorithm. We tested the placement accuracy of the system by using a needle phantom with radiopaque markers as targets. The system is routinely used for surface documentation and resulted in 24 surface documentations over the course of 11months. We performed accuracy tests for needle placement using a biopsy phantom, and the Virtobot placed introducer needles with an accuracy of 1.4mm (±0.9mm). The second prototype of the Virtobot system is an upgrade of the first prototype but mainly focuses on streamlining the workflow and increasing the level of automation and also has an easier user interface. These upgrades make the Virtobot a potentially valuable tool for case documentation in a scalpel-free setting that uses purely imaging techniques and minimally invasive procedures and is the next step toward the future of virtual autopsy

VirtoScan-on-Rails – an automated 3D imaging system for fast post-mortem whole-body surface documentation at autopsy tables

Two-dimensional photographic documentation is a substantial part of post-mortem examinations for legal investigations. Additional three-dimensional surface documentation has been shown to assist in the visualization of findings and contribute to the reconstruction of the sequence of events. However, 2D photo documentation and, especially, 3D surface documentation, are time-consuming procedures that require specially trained personnel. In this study a 3D imaging system, called VirtoScan-on-Rails, was developed to automate and facilitate 3D surface documentation for photo documentation in autopsy suites. The imaging system was built to quickly acquire photogrammetric image sets of whole bodies during different stages of external and internal examinations. VirtoScan-on-Rails was set up in the autopsy suite of the Zurich Institute of Forensic Medicine at the University of Zurich (Zurich, Switzerland). The imaging system is based on a movable frame that carries a multi-camera array. Data quality and the applicability of the system were analyzed and evaluated within two test series. Up to 200 overlapping photographic images were acquired at consecutive image-capturing positions over a distance of approximately 2000 mm. The image-capturing process took 1 min and 23 s to acquire a set of 200 images for one side of the body. During test series one and two, 53 photogrammetric image sets taken from 31 forensic cases were successfully reconstructed. VirtoScan-on-Rails is an automated, fast and easy-to-use 3D imaging setup for autopsy suits. It facilitates documenting bodies during different stages of forensic examinations and allows standardizing the procedure of photo documentation

Virtobot--a multi-functional robotic system for 3D surface scanning and automatic post mortem biopsy

The Virtopsy project, a multi-disciplinary project that involves forensic science, diagnostic imaging, computer science, automation technology, telematics and biomechanics, aims to develop new techniques to improve the outcome of forensic investigations. This paper presents a new approach in the field of minimally invasive virtual autopsy for a versatile robotic system that is able to perform three-dimensional (3D) surface scans as well as post mortem image-guided soft tissue biopsies