Lanthanoid-doped quaternary garnets as phosphors for high brightness cathodoluminescence-based light sources

Gadolinium-yttrium- aluminum-gallium garnets (GYAGG) doped and codoped with Eu, Tb, and Ce were manufactured as ceramics to develop long-wavelength phosphors for high-brightness white light sources based on cathodoluminescence (CL). The CL light yield (LY) of Tb-doped ceramics at high-intensity electron beam excitation is shown to be more than twice as high as that of the conventional phosphor YAG:Ce, whereas codoping with Eu to redshift the chromaticity results in reducing the LY approximately to the level of YAG:Ce. The LY might be substantially improved by using a mix of Tb- and Eu-doped GYGAG powders instead of a single codoped GYGAG to produce ceramic phosphor. The high LY is explained by favorable contribution of Gd sublattice in excitation transfer to activator ions. Chromaticity of phosphors GYGAG:Tb, Eu can be tuned in a wide range by varying the ratio of Tb to Eu concentration. They are radiation resistant and stabile in the temperature range from 300 to 450 K. © 2022 The Author(s)Ministry of Education and Science of the Russian Federation, Minobrnauka: 075-11-2021-070, 075-15-2021-1353, FEUZ-2020-0060This work was supported by the Ministry of Science and Higher Education of the Russian Federation (FEUZ-2020-0060, No. 075-15-2021-1353 & 075-11-2021-070)

Microstructural Features and Surface Hardening of Ultrafine-Grained Ti-6Al-4V Alloy through Plasma Electrolytic Polishing and Nitrogen Ion Implantation

This work studies a near-surface layer microstructure in Ti-6Al-4V alloy samples subjected to plasma electrolytic polishing (PEP) and subsequent high-energy ion implantation with nitrogen (II). Samples with a conventional coarse-grained (CG) structure with an average α-phase size of 8 μm and an ultrafine-grained (UFG) structure (α-phase size up to 0.35 μm) produced by equal channel angular pressing were used in the studies. Features of phase composition and substructure in the thin surface layers are shown after sequential processing by PEP and II of both substrates with CG and UFG structures. Irrespective of a substrate structure, the so-called “long-range effect” was observed, which manifested itself in enhanced microhardness to a depth of surface layer up to 40 μm, exceeding the penetration distance of an implanted ion he. The effect of a UFG structure on depth and degree of surface hardening after PEP and ion-implantation is discussed

Enhanced Erosion Resistance of an Ultrafine-Grained Ti Alloy with a PVD Coating

This paper presents the results of a comprehensive study of the erosive wear resistance, strength, and adhesive characteristics of the high-temperature structural titanium alloy Ti-5.7Al-3.8Mo-1.2Zr-1.3Sn (the Russian grade VT8M-1) with coarse-grained and ultrafine-grained (UFG) structures and a protective erosion-resistant TiVN coating produced by physical vapor deposition (PVD), deposited on the alloy surface. A microscopic analysis of the areas subjected to the action of abrasive particles was performed, and different characters of erosive wear were revealed depending on the structural state of the alloy. The obtained results convincingly demonstrate that by means of refining the grain structure of alloys and depositing a protective ion-plasma TiVN coating on the alloy surface, it is possible to significantly increase the erosion resistance of materials operating under high loads and in aggressive environments

Enhanced creep resistance of an ultrafine‐grained Ti–6Al–4V alloy with modified surface by ion implantation and (Ti + V)N coating

This research examines the creep behavior of an ultrafine-grained (UFG) Ti−6Al−4V alloy processed by equal-channel angular pressing followed by extrusion. It is shown that modifying the surface of the UFG alloy with nitrogen ions and then applying of a coating of (Ti + V)N inhibits the softening of the UFG alloy at temperatures up to 700 K due to a barrier effect in which the coating hinders the release of dislocations onto the surface. The differences in the mechanisms of crack initiation and failure of UFG samples are also examined both with and without a coating. The prospects of the proposed approach to the improving of titanium alloys are discussed, including the formation of an UFG structure in the bulk of the material and subsequent modification by ion-plasma methods for the manufacture of highly loaded parts operating at elevated operating temperatures.</p

Enhanced Erosion Resistance of an Ultrafine-Grained Ti Alloy with a PVD Coating

This paper presents the results of a comprehensive study of the erosive wear resistance, strength, and adhesive characteristics of the high-temperature structural titanium alloy Ti-5.7Al-3.8Mo-1.2Zr-1.3Sn (the Russian grade VT8M-1) with coarse-grained and ultrafine-grained (UFG) structures and a protective erosion-resistant TiVN coating produced by physical vapor deposition (PVD), deposited on the alloy surface. A microscopic analysis of the areas subjected to the action of abrasive particles was performed, and different characters of erosive wear were revealed depending on the structural state of the alloy. The obtained results convincingly demonstrate that by means of refining the grain structure of alloys and depositing a protective ion-plasma TiVN coating on the alloy surface, it is possible to significantly increase the erosion resistance of materials operating under high loads and in aggressive environments