TERRAIN ANALYSIS IN CONSIDERATION OF SURFACE CURVATURE CONDITIONS

In digital relief models determination of the terrain curvature can be realized without difficulty with the aid of the formulae figuring in the paper. Visualizing the results on maps, the curvature conditions can also be studied visually. After a computer aided analysis of the results the algorithm in the paper orders the surface points into seven categories (plane, peak, pit, pass, ridge, valley, slope) and/or their sub-categories. In a digital form, the resulting image matrix can supply further computer aided processes ,with information, and visualized in a graphic way it gives a good image about terrain formation. The results can be utilized in different branches of agricultural planning, in environmental protection, hydrological modeling, etc

Non-calorimetric determination of absorbed power during magnetic nanoparticle based hyperthermia

Nanomagnetic hyperthermia (NMH) is intensively studied with the prospect of cancer therapy. A major challenge is to determine the dissipated power during in vivo conditions and conventional methods are either invasive or inaccurate. We present a non-calorimetric method which yields the heat absorbed during hyperthermia: it is based on accurately measuring the quality factor change of a resonant radio frequency circuit which is employed for the irradiation. The approach provides the absorbed power in real-time, without the need to monitor the sample temperature as a function of time. As such, it is free from the problems caused by the non-adiabatic heating conditions of the usual calorimetry. We validate the method by comparing the dissipated power with a conventional calorimetric measurement. We present the validation for two types of resonators with very different filling factors: a solenoid and a so-called birdcage coil. The latter is a volume coil, which is generally used in magnetic resonance imaging (MRI) under in vivo condition. The presented method therefore allows to effectively combine MRI and thermotherapy and is thus readily adaptable to existing imaging hardware.Comment: 7 pages, 3 figures+Supplementary Material (2 pages, 3 figures

Doped carbon nanotubes as a model system of biased graphene

Albeit difficult to access experimentally, the density of states (DOS) is a key parameter in solid state systems which governs several important phenomena including transport, magnetism, thermal, and thermoelectric properties. We study DOS in an ensemble of potassium intercalated single-wall carbon nanotubes (SWCNT) and show using electron spin resonance spectroscopy that a sizeable number of electron states are present, which gives rise to a Fermi-liquid behavior in this material. A comparison between theoretical and the experimental DOS indicates that it does not display significant correlation effects, even though the pristine nanotube material shows a Luttinger-liquid behavior. We argue that the carbon nanotube ensemble essentially maps out the whole Brillouin zone of graphene thus it acts as a model system of biased graphene

Giant microwave absorption in fine powders of superconductors

Enhanced microwave absorption, larger than that in the normal state, is observed in fine grains of type-II superconductors (MgB$_2$ and K$_3$C$_{60}$) for magnetic fields as small as a few $\%$ of the upper critical field. The effect is predicted by the theory of vortex motion in type-II superconductors, however its direct observation has been elusive due to skin-depth limitations; conventional microwave absorption studies employ larger samples where the microwave magnetic field exclusion significantly lowers the absorption. We show that the enhancement is observable in grains smaller than the penetration depth. A quantitative analysis on K$_3$C$_{60}$ in the framework of the Coffey--Clem (CC) theory explains well the temperature dependence of the microwave absorption and also allows to determine the vortex pinning force constant

Ultrafast sensing of photoconductivity decay using microwave resonators

Microwave reflectance probed photoconductivity (or $\mu$-PCD) measurement represents a contactless and non-invasive method to characterize impurity content in semiconductors. Major drawbacks of the method include a difficult separation of reflectance due to dielectric and conduction effects and that the $\mu$-PCD signal is prohibitively weak for highly conducting samples. Both of these limitations could be tackled with the use of microwave resonators due to the well-known sensitivity of resonator parameters to minute changes in the material properties combined with a null measurement. A general misconception is that time resolution of resonator measurements is limited beyond their bandwidth by the readout electronics response time. While it is true for conventional resonator measurements, such as those employing a frequency sweep, we present a time-resolved resonator parameter readout method which overcomes these limitations and allows measurement of complex material parameters and to enhance $\mu$-PCD signals with the ultimate time resolution limit being the resonator time constant. This is achieved by detecting the transient response of microwave resonators on the timescale of a few 100 ns \emph{during} the $\mu$-PCD decay signal. The method employs a high-stability oscillator working with a fixed frequency which results in a stable and highly accurate measurement.Comment: 7 pages, 6 figures+Supplementary Material