46 research outputs found
Significance of DSMC Computed Aerothermal Environments in the Rarefied Regime for Atmospheric Entry Material Response
During Mars atmospheric entry, the Mars Science Laboratory (MSL) was protected by a 4.5 meters diameter ablative heatshield assembled in 113 tiles. The heatshield was made of NASA's flagship ablative material, the Phenolic Impregnated Carbon Ablator (PICA). Prior work compared the traditional one-dimensional and three-dimensional material response models at different locations in the heatshield. It was observed that the flow was basically one-dimensional in the nose and flank regions, but three-dimensional flow effects were observed in the outer flank. The objective of this work is to study the effects of the aerothermal environment on the material response. We extend prior work by computing aerothermal environments using the direct simulation Monte Carlo (DSMC) code SPARTA and the CFD code Data Parallel Line Relaxation (DPLR). SPARTA is used to compute environment in the rarefied regime prior to 48.4s of entry where the Knudsen number is such that the Navier-Stokes equations can be inaccurate. Similarly to previous work, the DPLR software is used to compute the hypersonic environment for laminar then turbulent boundary layer assumptions from 48.4 s up to 100 s after Entry Interface (EI) along the MSL 08-TPS-02/01a trajectory. We observe that extending the aerothermal environments to times prior to 48.4 s modifies the thermal response of the heat shield at the surface and in-depth; however the effects on the recession are minimal. Additionally, using the assumption of a turbulent boundary layer versus a laminar one leads to higher surface and in-depth temperatures, larger recession, and a displacement of the peak heating and peak recession location
Full-Scale MSL Heatshield Material Response Using DSMC and CFD to Compute the Aerothermal Environments
During Mars atmospheric entry, the Mars Science Laboratory (MSL) was protected by a 4.5 meters diameter ablative heatshield assembled in 113 tiles [1]. The heatshield was made of NASA's flagship ablative material, the Phenolic Impregnated Carbon Ablator (PICA) [2]. Prior work [3] compared the traditional one-dimensional and three-dimensional material response models at different locations in the heatshield. It was observed that the flow was basically one-dimensional in the nose and flank regions, but three-dimensional flow effects were observed in the outer flank. Additionally, the effects of tiled versus monolithic heatshield models were also investigated. It was observed that the 3D tiled and 3D monolithic configurations yielded relative differences for in-depth material temperature up to 18% and 28%, respectively, when compared to the a 1D model
Microscale Analysis of Spacecraft Heat Shields
Imagine entering Earths atmosphere after returning from the outer solar system. A heat shield less than 2 inches thick protects you from temperatures up to 2,900 Celsius (5,252 Fahrenheit). Such conditions were experienced by NASAs Stardust capsule during reentry in 2006. The only materials capable of providing the necessary protection are composites with complex microstructures. Evaluating these materials is difficult, requiring precise knowledge of their properties. To this end, NASA scientists are developing research codes to compute material properties and simulate ablation at the microscale using agency supercomputers. Utilizing these tools, along with experiments, researchers are working to push the limits of spaceflight, allowing for greater flexibility in future space missions
Development of a Water Cluster Evaporation Model using Molecular Dynamics
Abstract. A Monte Carlo simulation using the SPC potential model has been used to determine the potential energy and constant volume heat capacity of water dimers and trimers. It was found that the potential energy almost follows a linear trend versus temperature. The heat capacity fluctuates around 10 cal/mol/K and reaches a maximum around 220 K for the dimer and 240 K for the trimer. The Molecular Dynamics simulation has been used to evaporate water dimers and trimers. The cumulative evaporation probabilities were calculated for temperatures ranging from 240 K to 300 K. The cluster evaporation rates were calculated using Weerashinge's equation, and they were compared with the UDT rates. Both values were found to be in good agreement. Finally, vibrational frequencies were computed
Prediction of Thermal Protection System Material Permeability and Hydraulic Tortuosity Factor Using Direct Simulation Monte Carlo
Carbon preforms used in Thermal Protection System (TPS) materials are 80 to 90% porous, allowing for boundary layer and pyrolysis gases to flow through the porous regions. The bulk material properties such as permeability and hydraulic tortuosity factor affect the transport of the boundary layer gases. The use of Direct Simulation Monte Carlo along with the Klinkenberg permeability formulation allows us to compute the continuum permeability and Knudsen correction factor for flow in the transition regime. In this work, we have computed the permeability for two types of carbon preforms, namely, Morgan Felt and FiberForm, and assessed the effect of orientation on the permeability. Since both the materials are anisotropic, the permeability was found to depend on orientation, wherein, the materials are more permeable in the in-plane orientation than the through-thickness orientation. The through-thickness orientation was also more tortuous compared to the in-plane material orientation. Compared to Morgan Felt, FiberForm is less permeable, in both, through thickness and in-plane directions
Radiative Heat Transfer Modeling in Fibrous Porous Media
Phenolic-Impregnated Carbon Ablator (PICA) was developed at NASA Ames Research Center as a lightweight thermal protection system material for successful atmospheric entries. The objective of the current work is to compute the effective radiative conductivity of fibrous porous media, such as preforms used to make PICA, to enable the efficient design of materials that can meet the thermal performance goals of forthcoming space exploration missions
Chemische Verbindungen mit Antimon-Stickstoff-Bindungen : (ein Review)
Ein 脺berblick der Literaturangaben zu synthetisierten anorganischen (kohlenstofffreien) und elementorganischen (gemischten) Verbindungen mit Antimon-Stickstoff-Bindungen. Verallgemeinerungen der wichtigsten Verfahren zu ihrer Synthese, ihrer Eigenschaften und der Identifizierung der Bindungen mittels IR-Spektroskopie. Nachweis f眉r die M枚glichkeit der Polymerbildung in Systemen mit Antimon-Stickstoff-Bindungen
From Tomography to Material Properties of Thermal Protection Systems
A NASA Ames Research Center (ARC) effort, under the Entry Systems Modeling (ESM) project, aims at developing micro-tomography (micro-CT) experiments and simulations for studying materials used in hypersonic entry systems. X-ray micro-tomography allows for non-destructive 3D imaging of a materials micro-structure at the sub-micron scale, providing fiber-scale representations of porous thermal protection systems (TPS) materials. The technique has also allowed for In-situ experiments that can resolve response phenomena under realistic environmental conditions such as high temperature, mechanical loads, and oxidizing atmospheres. Simulation tools have been developed at the NASA Ames Research Center to determine material properties and material response from the high-fidelity tomographic representations of the porous materials with the goal of informing macroscopic TPS response models and guiding future TPS design
Microscale Modeling of High-Temperature Heat Transfer in Anisotropic Porous Materials
No abstract availabl