Optical study of sonic and supersonic jet penetration from a flat plate into a Mach 2 airstream

Optical study of sonic and supersonic jet penetration from flat plate into Mach 2 airstrea

Aerodynamic drag and fuel spreading measurements in a simulated scramjet combustion module

The drag of a simulated scramjet combustion module was measured at Mach 2, 2.5, and 3. The combustor was rectangular in cross section and incorporated six swept fuel injector struts. The effect of strut leading edge radius, position of maximum thickness, thickness ratio, sweep angle, and strut length on the drag was determined. Reduction in thickness ratio had the largest effect on drag reduction. Sweeping the struts upstream yielded the same drag as sweeping the struts downstream and potentially offers the advantages of increased mixing time for the fuel. Helium injection was used to simulate hydrogen fuel. The interstrut spacing required to achieve good distribution of fuel was was found to be about 10 jet diameters. The contribution of helium injection to drag reduction was small

Computational modeling and validation for hypersonic inlets

Hypersonic inlet research activity at NASA is reviewed. The basis is the experimental tests performed with three inlets: the NASA Lewis Research Center Mach 5, the McDonnell Douglas Mach 12, and the NASA Langley Mach 18. Both three-dimensional parabolized Navier-Stokes and Navier-Stokes codes were used to compute the flow within the three inlets. Modeling assumptions in the codes involve the turbulence model, the nature of the boundary layer, shock wave boundary layer interaction, and the flow spilled to the outside of the inlet. Use of the codes in conjunction with the experimental data are helping to develop a clearer understanding of the inlet flow physics and to focus on the modeling improvements required in order to arrive at validated codes

CFD for hypersonic propulsion

An overview is given of research activity on the application of computational fluid dynamics (CDF) for hypersonic propulsion systems. After the initial consideration of the highly integrated nature of air-breathing hypersonic engines and airframe, attention is directed toward computations carried out for the components of the engine. A generic inlet configuration is considered in order to demonstrate the highly three dimensional viscous flow behavior occurring within rectangular inlets. Reacting flow computations for simple jet injection as well as for more complex combustion chambers are then discussed in order to show the capability of viscous finite rate chemical reaction computer simulations. Finally, the nozzle flow fields are demonstrated, showing the existence of complex shear layers and shock structure in the exhaust plume. The general issues associated with code validation as well as the specific issue associated with the use of CFD for design are discussed. A prognosis for the success of CFD in the design of future propulsion systems is offered

Application of computational fluid dynamics in high speed aeropropulsion

The application is described of computational fluid dynamics (CFD) to a hypersonic propulsion system. An overview of the problems associated with a propulsion system of this type is presented, highlighting the special role that CFD plays in the design of said systems

Displacement of disintegrating liquid jets in crossflow

Breakup, and displacement of liquid jets in crossflow of shock tub

An aerodynamic study of scramjet fuel injectors

The aerodynamic drag and fuel distribution patterns of injectors designed for a supersonic combustion ramjet were measured at Mach numbers of 2, 2.5, and 3. The most significant parameter effecting the drag was found to be the injector thickness ratio. A two-fold reduction in the thickness ratio caused a 65 percent decrease in drag. Changing the injector sweep angle a factor of 2 resulted in only a small change in drag. A reversal of injector sweep, from sweepback to sweepforward, did not change the measured drag. Helium gas was injected through the struts to simulate the penetration and spreading patterns of hydrogen. Sampling measurements were made at approximately 2 duct heights downstream of the combustor. The spacing required between fuel injectors was found to be about 10 jet diameters. The effect of gas injection on the measured drag was found to be minor

Validation of viscous and inviscid computational methods for turbomachinery components

An assessment of several three-dimensional computer codes used at the NASA Lewis Research Center is presented. Four flow situations are examined, for which both experimental data and computational results are available. The four flows form a basis for the evaluation of the computational procedures. It is concluded that transonic rotor flow at peak efficiency conditions may be calculated with a reasonable degree of accuracy, whereas, off-design conditions are not accurately determined. Duct flows and turbine cascade flows may also be computed with reasonable accuracy whereas radial inflow turbine flow remains a challenging problem

An experimental and analytical investigation of axisymmetric diffusers

A finite difference computer program for turbulent compressible flow was used to establish the performance of several diffuser shapes for experimental testing. The diffusers were designed to have a linear change in Mach number, a linear change in pressure, or a curvature fitted by a quadratic equation. Testing was performed with M = 0.1 to 0.9 with and without boundary layer bleed. Above M = 0.6, data were obtained with a normal shock upstream of the diffuser entrance. Peak static pressure recovery occurred with a diffuser inlet M0.75. The quadratic diffuser yielded the highest total pressure recovery

Some aspects of steady-state propellant combustion as related to dynamic coupling mechanisms

Dynamic pressure and velocity coupling mechanisms in steady-state solid propellant combustio