Heat treatment for superalloy

A cobalt-free nickel-base superalloy composed of in weight % 15 Cr-5 Mo-3.5 Ti-4 Al-0.07 (max) C-remainder Ni is given a modified heat treatment. With this heat treatment the cobalt-free alloy achieves certain of the mechanical properties of the corresponding cobalt-containing nickel-base superalloy at 1200 F (650 C). Thus, strategic cobalt can be replaced by nickel in the alloy

Mechanical properties of modified low cobalt powder metallurgy Udimet 700 type alloys

Eight superalloys derived from Udimet 700 were prepared by powder metallurgy, hot isostatically pressed, heat treated and their tensile and creep rupture properties determined. Several of these alloys displayed properties superior to those of Udimet 700 similarly prepared, in one case exceeding the creep rupture life tenfold. Filter clogging by extracted gamma prime, its measurement and significance are discussed in an appendix

A Directionally Solidified Iron-chromium-aluminum-tantalum Carbide Eutectic Alloy

A eutectic alloy, Fe-13.6CR-3.7Al+9TaC, was directionally solidified in a high gradient furnace, producing a microstructure of alined TaC fibers in an oxidation resistant alpha-iron matrix. Tensile and stress rupture properties, thermal cycling resistance, and microstructures were evaluated. The alloy displays at 1000 C an ultimate tensile strength of 58 MPa and a 100-hour rupture life at a stress of 21 MPa. Thermal cycling to 1100 C induces faceting in the TaC fibers

Properties and microstructures for dual alloy combinations of three superalloys with alloy 901

Dual alloy combinations have potential for use in aircraft engine components such as turbine disks where a wide range of stress and temperature regimes exists during operation. Such alloy combinations may directly result in the conservation of elements which are costly or not available domestically. Preferably, a uniform heat treatment yielding good properties for both alloys should be used. Dual alloy combinations of iron rich Alloy 901 with nickel base superalloys Rene 95, Astroloy, or MERL 76 were not isostatically pressed from prealloyed powders. Individual alloys, alloy mixtures, and layered alloy combinations were given the heat treatments specified for their use in turbine disks or appropriate for Alloy 901. Selected specimens were overaged for 1500 hr at 650 C. Metallographic examinations revealed the absence of phases not originally present in either alloy of a combination. Mechanical tests showed adequate properties in combinations of Rene 95 or Astroloy with Alloy 901 when given the Alloy 901 heat treatment. Combinations with MERL 76 had better properties when given the MERL 76 heat treatment. The results indicate that these combinations are promising candidates for use in turbine disks

The response of cobalt-free Udimet 700 type alloy to modified heat treatments

A superalloy based on Udimet 700, in which all of the cobalt was replaced by nickel, was prepared from hot isostatically pressed prealloyed powders. This material was given various heat treatments consisting of partial solutioning and aging in a sequence of four different temperatures. Comparisons were made of microstructures and mechanical properties. Best results were obtained by partially solutioning at 1145 deg C and aging through a sequence of 870, 1030, 650 and 760 deg C. This heat treatment also provided significantly improved properties for wrought material of the same composition. The results suggest that cobalt free Udimet 700 should be considered as a substitute for Udimet 700 with the standard 17 percent cobalt content

The effect of thermal cycling to 1100 degree C on the alpha (Mo) phase in directionally solidified gamma/gamma prime-alpha alloys

In gamma/gamma prime - alpha eutectic alloys (Ni-Mo-Al), the resistance of the alpha phase to morphological changes during thermal cycling was found to be dependent on the structure formed during directional solidification. Fine, smooth alpha fibers survived up to 1000 five minute cycles to 1100 C with minor microstructural contour changes, while coarser and irregularly shaped alpha fibers tended to spheroidize. A mechanism to explain this phenomenon is proposed. It is suggested that on heating to 1100 C, the alpha phase is likely to undergo morphological changes, until differential thermal expansion creates a stress free interface between the alpha phase and the gamma/gamma prime matrix

Microstructural behavior of interfaces in hot isostatically pressed, dual alloy combinations

Combinations of the nickel-base superalloys MERL 76 and low carbon Astroloy, Rene 95 and low carbon Astroloy, Rene 95 and NASA-TRW-VIA were consolidated from prealloyed powders by hot isostatic pressing. These combinations were exposed to 870 C for 1500 hours, and in a gradient furnance to temperatures up to incipient melting and subjected to microstructural examinations. The only phases found at the interfaces were those which were also present in the component alloys

Cobalt base superalloy has outstanding properties up to 1478 K (2200 F)

Alloy VM-103 is especially promising for use in applications requiring short time exposure to very high temperatures. Its properties over broad range of temperatures are superior to those of comparable commercial wrought cobalt-base superalloys, L-605 and HS-188

The Decline of Traditional Pensions, the Impact of the Pension Protection Act of 2006, and the Future of America\u27s Defined-Benefit Pension System

Congress passed the Pension Protection Act of 2006 to provide economic security for millions of Americans dependent on traditional defined-benefit pension plans, plans where an employer has promised to pay for the retirement of its employees. The bill was necessitated by the many employers who had terminated their plans both inside and outside of bankruptcy protection. This note will discuss the history of the defined-benefit pension system, the ways these plans can be terminated, and the problems these terminations pose for employers, employees, and the American taxpayers. It will argue that the Act and its exceptions for those in the airline industry could be a good first start for protecting those Americans who expected to have a defined-benefit plan as their retirement savings. Nevertheless, there are some glaring deficiencies with the Act, including the fact that it fails to give similar exceptions for other troubled industries, such as the automotive industry. Finally, this note will argue that defined-benefit plans are a dying breed and today\u27s workers must be made to understand that they cannot depend on such plans

A new nickel-base wrought superalloy for applications up to 1033 K (1400 F)

Alloy was melted from high purity raw materials and cast ingots extruded at 1422 K. Material was hot rolled to 0.013 m diameter bar stock. Partial solution heat-treatment followed by aging produced structure of fine gamma prime precipitate reinforcing gamma matrix containing coarser blocky gamma prime particles. Alloy can be processed by powder metallurgy