Thermographic Particle Velocimetry (TPV) for Simultaneous Interfacial Temperature and Velocity Measurements

AbstractWe present an experimental technique, that we refer to as ‘thermographic particle velocimetry’ (TPV), which is capable of the simultaneous measurement of two-dimensional (2-D) surface temperature and velocity at the interface of multiphase flows. The development of the technique has been motivated by the need to study gravity-driven liquid-film flows over inclined heated substrates, however, the same measurement principle can be applied for the recovery of 2-D temperature- and velocity-field information at the interface of any flow with a sufficient density gradient between two fluid phases. The proposed technique relies on a single infrared (IR) imager and is based on the employment of highly reflective (here, silver-coated) particles which, when suspended near or at the interface, can be distinguished from the surrounding fluid domain due to their different emissivity. Image processing steps used to recover the temperature and velocity distributions include the decomposition of each original raw IR image into separate thermal and particle images, the application of perspective distortion corrections and spatial calibration, and finally the implementation of standard particle velocimetry algorithms. This procedure is demonstrated by application of the technique to a heated and stirred flow in an open container. In addition, two validation experiments are presented, one dedicated to the measurement of interfacial temperature and one to the measurement of interfacial velocity. The deviations between the results generated from TPV and those from accompanying conventional techniques do not exceed the errors associated with the latter

Development of a Thermographic Imaging Technique for Simultaneous Interfacial Temperature and Velocity Measurements

An experimental technique, hereby referred to as ‘thermographic particle velocimetry’ (TPV) and capable of recovering twodimensional (2-D) surface temperature and velocity measurements at the interface of multiphase flows is presented. The proposed technique employs a single infrared (IR) imager and highly reflective, silver-coated particles, which when suspended near or at the interface, can be distinguished from the surrounding fluid due to their different emissivity. The development of TPV builds upon our previous IR imaging studies of heated liquid-film flows; yet, the same measurement principle can be applied for the recovery of 2-D temperature- and velocity-field information at the interface of any flow with a significant density gradient between two fluid phases. The image processing steps used to recover the temperature and velocity distributions from raw IR frames are demonstrated by application of TPV in a heated and stirred flow in an open container, and include the decomposition of each raw frame into separate thermal and particle frames, the application of perspective distortion corrections and spatial calibration, and the implementation of standard particle image velocimetry algorithms. Validation experiments dedicated to the measurement of interfacial temperature and velocity were also conducted, with deviations between the results generated from TPV and those from accompanying conventional techniques not exceeding the errors associated with the latter. Finally, the capabilities of the proposed technique are demonstrated by conducting temperature and velocity measurements at the gas-liquid interface of a wavy film flow downstream of a localised heater

Experimental investigation of the flow in a micro-channelled combustor and its relation to flame behaviour

© 2020 Elsevier Inc. The dynamic behaviour of periodic laminar premixed acetylene-air flames in a micro-channelled combustor consisting of an array of five planar rectangular channels was found to be influenced by the equivalence ratio and flow-rate of the continuously and steadily injected premixed fuel charge. Three distinct flame stages were observed — planar, chaotic and trident, which were strongly correlated to the flow dynamics. The effect of the flow on the flame behaviour was investigated by characterizing the cold flow in a scaled-up model channel with the same aspect ratio as the combustion micro-channel. Direct flow visualization using flow tracers and quantitative velocity-field data from PIV measurements showed both an increase in the bottom recirculation zone reattachment length (along the floor of the channel) and a decrease in the lateral recirculation zone reattachment length (along the sides of the channel) with increasing flow Reynolds number. Comparison of the flow and flame transition locations downstream of the injection point suggested that the location of trident flame onset coincides with the flow bottom recirculation zone reattachment length. The planar-chaotic flame transition location was observed to be influenced by the homogeneity of the mixture downstream of the injection plane

Harnessing the potential of ligninolytic enzymes for lignocellulosic biomass pretreatment

Abundant lignocellulosic biomass from various industries provides a great potential feedstock for the production of value-added products such as biofuel, animal feed, and paper pulping. However, low yield of sugar obtained from lignocellulosic hydrolysate is usually due to the presence of lignin that acts as a protective barrier for cellulose and thus restricts the accessibility of the enzyme to work on the cellulosic component. This review focuses on the significance of biological pretreatment specifically using ligninolytic enzymes as an alternative method apart from the conventional physical and chemical pretreatment. Different modes of biological pretreatment are discussed in this paper which is based on (i) fungal pretreatment where fungi mycelia colonise and directly attack the substrate by releasing ligninolytic enzymes and (ii) enzymatic pretreatment using ligninolytic enzymes to counter the drawbacks of fungal pretreatment. This review also discusses the important factors of biological pretreatment using ligninolytic enzymes such as nature of the lignocellulosic biomass, pH, temperature, presence of mediator, oxygen, and surfactant during the biodelignification process