Silicon Solar Cell Process Development, Fabrication and Analysis, Phase 1

Solar cells from RTR ribbons, EFG (RF and RH) ribbons, dendritic webs, Silso wafers, cast silicon by HEM, silicon on ceramic, and continuous Czochralski ingots were fabricated using a standard process typical of those used currently in the silicon solar cell industry. Back surface field (BSF) processing and other process modifications were included to give preliminary indications of possible improved performance. The parameters measured included open circuit voltage, short circuit current, curve fill factor, and conversion efficiency (all taken under AM0 illumination). Also measured for typical cells were spectral response, dark I-V characteristics, minority carrier diffusion length, and photoresponse by fine light spot scanning. the results were compared to the properties of cells made from conventional single crystalline Czochralski silicon with an emphasis on statistical evaluation. Limited efforts were made to identify growth defects which will influence solar cell performance

Silicon solar cell process development, fabrication, and analysis

Two large cast ingots were evaluated. Solar cell performance versus substrate position within the ingots was obtained and the results are presented. Dendritic web samples were analyzed in terms of structural defects, and efforts were made to correlate the data with the performance of solar cells made from the webs

Silicon solar cell process development, fabrication and analysis

Solar cells were fabricated from EFG ribbons dendritic webs, cast ingots by heat exchanger method, and cast ingots by ubiquitous crystallization process. Baseline and other process variations were applied to fabricate solar cells. EFG ribbons grown in a carbon-containing gas atmosphere showed significant improvement in silicon quality. Baseline solar cells from dendritic webs of various runs indicated that the quality of the webs under investigation was not as good as the conventional CZ silicon, showing an average minority carrier diffusion length of about 60 um versus 120 um of CZ wafers. Detail evaluation of large cast ingots by HEM showed ingot reproducibility problems from run to run and uniformity problems of sheet quality within an ingot. Initial evaluation of the wafers prepared from the cast polycrystalline ingots by UCP suggested that the quality of the wafers from this process is considerably lower than the conventional CZ wafers. Overall performance was relatively uniform, except for a few cells which showed shunting problems caused by inclusions

Two Methods for the Computation of Commercial Pipe Friction Factors

Two methods are proposed for the computation of friction factors of commercial pipes. The first method applies the mean value of the zero velocity point (MZVP) to a theoretical friction factor equation, and the other directly computes the mean friction factor (MFF) by averaging the friction factor of both the smooth and rough walls while considering their relative contribution. The MFF method is preferred, because it is simple but covers all the flow characteristics of commercial pipes. Both MFF and MZVP methods consider two parts of a wall with different roughness heights: One part is rough and the other is smooth. A regression analysis was performed to determine optimum values of the roughness height and probability of encountering each part, using several sets of field data, including galvanized iron, wrought iron, cast iron, concrete, riveted steel, and concrete. The analysis showed that both the roughness height and the relative contribution of the rough part are strongly dependent on the pipe diameter. The MFF method gave an average error of less than 3%, whereas the traditional Colebrook–White equation gave an average error of more than 11% when compared with Colebrook’s data

Isolation and characterization of cellulose degrading ability in Paenibacillus isolates from landfill leachate

Aims: Cellulases are enzymes that convert cellulose into glucose molecules, and are produced by various microorganisms in the environment. Due to their importance to the biofuel industry, there is a need to screen for more efficient varieties of cellulases. In this study, leachate samples from a landfill site were screened for cellulolytic bacteria. Methodology and results: Leachate samples obtained from a landfill collection pond were cultured in an enriched cellulose medium. Two cellulolytic isolates, designated MAEPY1 and MAEPY2, were isolated and further characterized. Phenotypic profiles and phylogenetic analyses using sequences of 16S rRNA, gyrB and whole genome suggested that these isolates are new strains of the Paenibacillus genera. The crude enzyme extracts from both isolates have cellulose degradation activity at approximately 0.1-0.2 IU/mg under working conditions of pH 6 and 55 °C. Assays using other lignocellulosic substrates showed that the crude enzyme extracts also have high xylan degradation activity. Conclusion, significance and impact of study: Paenibacillus sp. are known to produce multiple enzymes for lignocellulolytic degradation and the present results suggest that isolates described in this study, MAEPY1 and MAEPY2, are excellent candidates deserving further study as potential producers of efficient cellulases for use in industries associated with cellulosic biomass

The Use of Polarization Filters to Detect the Edge of the Descemet’s Stripping Automated Endothelial Keratoplasty(DSAEK) Graft

To report the technique of combining the two different polarization filters to detect the flap edge of the corneoscleral tissue before trephining the Descemet's stripping automated endothelial keratoplasty (DSAEK) tissue. A human DSAEK donor tissue was prepared with mechanical microkeratome and the tissue on the cutting block was brought under the microscope. The liner, circular, or the combination of these two polarization filters was placed between the tissue and the microscope. The tissue images were taken with digital camera under either of 3 settings. The combination of circular and linear polarization filters enabled us to recognize the edge of the flap more easily than others. This simple system with polarization filters was effective in clear visualization of the flap edge during DSAEK tissue preparation. These features may significantly enhance safety of various surgical procedures, in addition to DSAEK tissue preparation

Influence of gravitational field on quantum-nondemolition measurement of atomic momentum in the dispersive Jaynes-Cummings model

We present a theoretical scheme based on su(2) algebra to investigate the influence of homogeneous gravitational field on the quantum nondemolition measurement of atomic momentum in dispersive Jaynes-Cummings model. In the dispersive Jaynes-Cummings model, when detuning is large and the atomic motion is in a propagating light wave, we consider a two-level atom with quantized cavity-field in the presence of a homogeneous gravitational field. We derive an effective Hamiltonian describing the dispersive atom-field interaction in the presence of gravitational field. We can see gravitational influence both on the momentum filter and momentum distribution. Moreover, gravitational field decreases both tooth spacing of momentum and the width of teeth of momentum.Comment: 21 pages, 8 figure

Silicon Solar Cell Process Development, Fabrication and Analysis

Ribbon to Ribbon (RTR) solar cells processed from polycrystalline feedstock showed maximum AMO efficiency of 5.6%. Solar cells from single crystalline feedstock showed slightly higher efficiency than those from polycrystalline feedstock, indicating maximum efficiency of about 6.6% with SiO AR coating. Single crystalline control cells gave 11-12% AMO efficiencies demonstrating that the poor performance of the RTR solar was due to the low quality of material itself. Dendritic web solar cells from the standard process showed maximum AMO efficiency of 9.8% while efficiency of control solar cells were around 11-12%. Web solar cells from back surface field (BSF) process indicated maximum AMO efficiency of 10.9%. Some improvement in open circuit voltage was noticed from the BSF process. Small light spot scanning experiments were carried out on the solar cells from Wacker Silso, EFG, RTR, and dendritic web ribbons. Photoresponse results provided information on localized cell performance and grain size in polycrystalline material, and agreed quite well with the cell performance data, such as efficiency, minority carrier diffusion length, and spectral response

Search for axion-like particles using a variable baseline photon regeneration technique

We report the first results of the GammeV experiment, a search for milli-eV mass particles with axion-like couplings to two photons. The search is performed using a "light shining through a wall" technique where incident photons oscillate into new weakly interacting particles that are able to pass through the wall and subsequently regenerate back into detectable photons. The oscillation baseline of the apparatus is variable, thus allowing probes of different values of particle mass. We find no excess of events above background and are able to constrain the two-photon couplings of possible new scalar (pseudoscalar) particles to be less than 3.1x10^{-7} GeV^{-1} (3.5x10^{-7} GeV^{-1}) in the limit of massless particles.Comment: 5 pages, 4 figures. This is the version accepted by PRL and includes updated limit

On the Sign Problem in the Hirsch-Fye Algorithm for Impurity Problems

We show that there is no fermion sign problem in the Hirsch and Fye algorithm for the single-impurity Anderson model. Beyond the particle-hole symmetric case for which a simple proof exists, this has been known only empirically. Here we prove the nonexistence of a sign problem for the general case by showing that each spin trace for a given Ising configuration is separately positive. We further use this insight to analyze under what conditions orbitally degenerate Anderson models or the two-impurity Anderson model develop a sign.Comment: 2 pages, no figure; published versio