Combined analysis of microstructures within an annual ring of Douglas fir (Pseudotsuga menziesii) by dynamic mechanical analysis and small angle X-ray scattering

Dynamic mechanical analysis (DMA) and small angle X-ray scattering (SAXS) measurements of water-saturated wood of Douglas fir (Pseudotsuga menziesii) in the temperature range of 0 ℃ to 100 ℃ were focused to clarify microstructural changes within an annual ring. The following results were obtained. Thermal softening behavior caused by micro-Brownian motion of lignin was observed in both earlywood and latewood. The peaks of tanδ were found at around 95 ℃ for earlywood and at around 90 ℃ for latewood. These results suggested that the structures of lignin in the cell wall were different between earlywood and latewood. SAXS measurements of water-saturated earlywood and latewood in water were performed with precise temperature control. The scattering intensity increased with increasing temperature, indicating that the density of the matrix was reduced at higher temperature. One-dimensional SAXS intensity at the equator, which approximately represents cellulose microfibrils arrangement in the matrix, was intensively analyzed using the WoodSAS model. The result of this model fitting showed that the cellulose microfibril diameter of latewood was higher than that of earlywood. In addition, the value of interfibrillar distance decreased monotonically in the earlywood, while it decreased rapidly in the latewood from 60 ℃ to 90 ℃. The changes in the cellulose microfibril (CMF) diameter and the interfibrillar distance with increasing temperature between earlywood and latewood by SAXS measurement were different. The differences in CMF diameter and inter-fibril distance between earlywood and latewood measured by SAXS also support the hypothesis that lignin structure differs between earlywood and latewood based on the results of DMA measurements

Can Pallidal Deep Brain Stimulation Rescue Borderline Dystonia? Possible Coexistence of Functional (Psychogenic) and Organic Components

The diagnosis and treatment of functional movement disorders are challenging for clinicians who manage patients with movement disorders. The borderline between functional and organic dystonia is often ambiguous. Patients with functional dystonia are poor responders to pallidal deep brain stimulation (DBS) and are not good candidates for DBS surgery. Thus, if patients with medically refractory dystonia have functional features, they are usually left untreated with DBS surgery. In order to investigate the outcome of functional dystonia in response to pallidal DBS surgery, we retrospectively included five patients with this condition. Their dystonia was diagnosed as organic by dystonia specialists and also as functional according to the Fahn and Williams criteria or the Gupta and Lang Proposed Revisions. Microelectrode recordings in the globus pallidus internus of all patients showed a cell-firing pattern of bursting with interburst intervals, which is considered typical of organic dystonia. Although their clinical course after DBS surgery was incongruent to organic dystonia, the outcome was good. Our results question the possibility to clearly differentiate functional dystonia from organic dystonia. We hypothesized that functional dystonia can coexist with organic dystonia, and that medically intractable dystonia with combined functional and organic features can be successfully treated by DBS surgery

モウソウチク ノ セイブツ レッカ トクセイ ト カンレンスル イクツカ ノ カガクテキ ブツリテキ セイシツ ニ ツイテ

京都大学0048新制・課程博士博士(農学)甲第13109号農博第1614号新制||農||940(附属図書館)学位論文||H19||N4235(農学部図書室)UT51-2007-H382京都大学大学院農学研究科森林科学専攻(主査)教授 今村 祐嗣, 教授 杉山 淳司, 教授 東 順一学位規則第4条第1項該当Doctor of Agricultural ScienceKyoto UniversityDA

Resistance of wood coated with oriental lacquer (urushi) against damage caused by subterranean termite

The sap of urushi tree (Toxicodendron vernicifluum (Stokes) F.A. Barkley) has been used for coating materials and is known as urushi or oriental lacquer in East Asia. The potential of termite attacks against wood samples coated with four types of urushi: Ki-urushi, Sugurome-urushi, Kuro-Sugurome-urushi, and Bengara-urushi, in correlation with their chemical and mechanical properties was investigated in this study. Mortalities of the subterranean Formosan termite (Coptotermes formosanus Shiraki) after a 3-week no-choice feeding tests in samples coated with all types of urushi showed no significant difference from those of control samples. However, mass loss of the sample coated with urushi was lower than that of the control sample especially for Sugurome-urushi (Tukey’s test: p < 0.05). Results of Fourier transform infrared spectra analysis suggested that the degree of crosslinking reaction of Sugurome-urushi was higher than that of other urushi. The highest indentation stiffness was detected in the sample surface coated with Sugurome-urushi and Sugurome-urushi film, which have better ductile properties when compared with others. Moreover, the tangential section of Sugurome-urushi was smoother than that of the others. Increasing the hardness and smoothness of wood samples by coating with urushi could be effective in preventing termite penetration

Reconstruction of Fibroin Nanofibers (FNFs) via Electrospinning: Fabrication of Poly(vinyl alcohol)/FNFs Composite Nanofibers from Aqueous Solution

Fibroin nanofibers (FNFs) achieved from physical treated silk can keep its original crystal structure, showing excellent mechanical properties, however, processing the FNFs into fibers is still a challenge. Herein, a brand-new environmentally friendly approach is proposed to manufacture FNFs-based composite nanofibers. The water-soluble polymer, poly(vinyl alcohol) PVA, was applied to increase the viscoelasticity of the spinning dope, and the content of FNFs can reach up to 20 wt%. The established phase image of spinning suggested that the concentrations ranging from 6 wt% to 8 wt% are premium to achieving relatively homogenous FNFs/PVA nanofibers. Random fibers were deposited on a fixed collector, while the fiber orientation intensity increased with the rotational speed of drum and started decreasing after 12 m/s. The mechanical properties of the composite nanofibers showed the similar tendency of variation of fiber orientation. In addition, chemical changes, crystallinity, and thermal properties of the composite nanofibers were further clarified by means of FTIR, DSC, and TG. As a result, high FNFs contained nanofibers with excellent thermal properties were created from an aqueous solution. This study is the first original work to realize the spinnability of FNFs, which provides a new insight of the FNFs