5 research outputs found
Nickel Oxide Grafted Andic Soil for Efficient Cesium Removal from Aqueous Solution: Adsorption Behavior and Mechanisms
An
andic soil, akadama clay, was modified with nickel oxide and
tested for its potential application in the removal of cesium from
aqueous solution. Scanning electron microscope (SEM), energy dispersive
X-ray spectroscopy (EDS), and powder X-ray diffraction (XRD) results
revealed the nickel oxide was successfully grafted into akadama clay.
N<sub>2</sub> adsorption–desorption isotherms indicated the
surface area decreased remarkably after modification while the portion
of mesopores increased greatly. Thermogravimetric-differential thermal
analysis (TG-DTA) showed the modified akadama clay had better thermostability
than the pristine akadama clay. Decreases in cation exchange capacity
(CEC) and ζ-potential were also detected after the modification.
Adsorption kinetic and isotherm studies indicated the adsorption of
Cs<sup>+</sup> on the modified akadama clay was a monolayer adsorption
process. Adsorption capacity was greatly enhanced for the modified
akadama clay probably due to the increase in negative surface charge
caused by the modification. The adsorption of Cs<sup>+</sup> on the
modified akadama clay was dominated by an electrostatic adsorption
process. Results of this work are of great significance for the application
of akadama clay as a promising adsorbent material for cesium removal
from aqueous solutions
DataSheet1_Synthesis and characterization of 3D-zeolite–modified TiO2-based photocatalyst with synergistic effect for elimination of organic pollutant in wastewater treatment.docx
In this work, zeolite, a porous material with a 3D network structure, was introduced as the carrier to support P/Ag/Ag2O/Ag3PO4/TiO2 (PAgT) composite for synthesizing the 3D-zeolite–modified photocatalyst (Z-PAgT). In this combination, zeolite with strong adsorbability can pre-adsorb and condense organic compounds onto the catalyst surface, thereby helping to speed up the photocatalytic reaction. In the present study, to determine the optimum mass ratio of zeolite to photocatalyst, various samples containing different zeolite additions (0 wt%, 5 wt%, 10 wt%, and 25 wt%) were prepared using the hydrothermal method, respectively. The physical–chemical properties of the as-prepared samples were systematically characterized by different analytical techniques, including XRD, FTIR, SEM, BET, EDX, UV-Vis, and PL. The results revealed that the obtained Z-PAgT-5 sample possessed relatively higher crystallinity, smaller crystalline size, larger specific surface area, narrow band gap, and lower generated electron-hole recombination rate. The photocatalytic degradation of rhodamine B (Rh B) in aqueous suspension has been employed to evaluate the photocatalytic activity of the as-prepared photocatalysts with simulated solar light as an irradiation source. The results showed that Z-PAgT-5 performed the highest photodegradation efficiency, and its degradation rate constant (kapp) (0.188 min−1) is much higher than that of Z-PAgT-0 (0.132 min−1), Z-PAgT-10 (0.050 min−1), Z-PAgT-25 (0.037 min−1), and pure zeolite (0.003 min−1). This super photocatalytic activity of Z-PAgT-5 toward Rh B degradation can be ascribed to the synergistic effect between the 3D-zeolite and PAgT photocatalyst, which made the hybrid zeolite-photocatalyst material possess good adsorption and photodegradation properties. In addition, repetitive experiments demonstrated that the improved Rh B degradation efficiency of Z-PAgT-5 was well maintained even after five recycling runs without any obvious decrease. Hence, the obtained results indicated that Z-PAgT-5 material can be used as a potential photocatalyst for treating organic pollutants during wastewater environmental remediation.</p
Additional file 1 of Comparative transcriptome analysis provides molecular insights into heterosis of waterlogging tolerance in Chrysanthemum indicum
Supplementary Material