521 research outputs found
Características agronômicas de 13 cultivares de arroz em Sistema Irrigado.
Com o proposito de dar informacoes de pesquisas aos agricultores e tecnicos que lidam com a orizicultura, procurou-se estudar o rendimento de graos e outras caracteristicas agronomicas de 13 cultivares de arroz sob condicoes de irrigacao por inundacao. O conhecimento destes fatores, aliados as boas qualidades de engenho e culinaria, conduzem ao sucesso de uma lavoura comercial. Desse modo, ao se escolher cultivar(es) deve-se verificar, antecipadamente, todas as suas caracteristicas agronomicas e comerciais a fim de evitar frustracoes de safra.bitstream/item/95656/1/CT040001.pd
Исследование и разработка гистерезисных электрических машин на основе деформируемого сплава Fe-Cr-Co
В ходе научно-квалификационной работы исследован материал ротора синхронного гистерезисного двигателя (СГД) из сплава 22Х15КА ГОСТ 24897-81. Получены динамические магнитные характеристики сплава на частотах перемагничивания от 50 Гц до 2 кГц. Представлены результаты исследования СГД в программной среде AnsysMaxwell 2D/3D.In the course of the scientific and qualifying work, the rotor material of the synchronous hysteresis motor from alloy 22Х15КА GOST 24897-81 was investigated. Dynamic magnetic characteristics of the alloy at the magnetization reversal frequencies from 50 Hz to 2 kHz are obtained. The results of the study of a synchronous hysteresis motor in the software environment of AnsysMaxwell 2D / 3D are presented
Development of the heat and mass transfer model for the study of the temperature traces water droplets in a flame
The heat and mass transfer model is developed with using Ansys Fluent. The typical temperature of gases in the trace of water droplets is determined (initial temperature of gases 1170 К). Several types for the location of water droplets are studied: two successive water droplets; two parallel water droplets; five water droplets in checkerboard order. The hypothesis about gas temperature reduction in the trace of a moving liquid is confirmed
The First 1 1/2 Years of TOTEM Roman Pot Operation at LHC
Since the LHC running season 2010, the TOTEM Roman Pots (RPs) are fully
operational and serve for collecting elastic and diffractive proton-proton
scattering data. Like for other moveable devices approaching the high intensity
LHC beams, a reliable and precise control of the RP position is critical to
machine protection. After a review of the RP movement control and position
interlock system, the crucial task of alignment will be discussed.Comment: 3 pages, 6 figures; 2nd International Particle Accelerator Conference
(IPAC 2011), San Sebastian, Spain; contribution MOPO01
Исследование высокотемпературной проницаемости водорода в циркониевом сплаве Э110 с нанесенным слоем никеля
Объектом исследований являлся циркониевый сплав Э110 с нанесенным слоем никеля. С помощью автоматизированного комплекса Gas Reaction Controller LP было определено накопление и распределение водорода в циркониевом сплаве Э110 с нанесенным слоем никеля.The research object is a zirconium alloy E110 with a nickel deposit. Using an automatic complex gas reaction controller LP, the accumulation and distribution of hydrogen in the E110 zirconium alloy with a deposited nickel layer was determined
Testing Beam-Induced Quench Levels of LHC Superconducting Magnets
In the years 2009-2013 the Large Hadron Collider (LHC) has been operated with
the top beam energies of 3.5 TeV and 4 TeV per proton (from 2012) instead of
the nominal 7 TeV. The currents in the superconducting magnets were reduced
accordingly. To date only seventeen beam-induced quenches have occurred; eight
of them during specially designed quench tests, the others during injection.
There has not been a single beam- induced quench during normal collider
operation with stored beam. The conditions, however, are expected to become
much more challenging after the long LHC shutdown. The magnets will be
operating at near nominal currents, and in the presence of high energy and high
intensity beams with a stored energy of up to 362 MJ per beam. In this paper we
summarize our efforts to understand the quench levels of LHC superconducting
magnets. We describe beam-loss events and dedicated experiments with beam, as
well as the simulation methods used to reproduce the observable signals. The
simulated energy deposition in the coils is compared to the quench levels
predicted by electro-thermal models, thus allowing to validate and improve the
models which are used to set beam-dump thresholds on beam-loss monitors for Run
2.Comment: 19 page
Characterization of the radiation tolerance of cryogenic diodes for the High Luminosity LHC inner triplet circuit
Cryogenic bypass diodes are part of the baseline powering layout for the circuits of the new Nb3Sn based final focus magnets of the high luminosity Large Hadron Collider. They will protect the magnets against excessive transient voltages during a nonuniform quenching process. The diodes are located inside an extension to the magnet cryostat, operated in superfluid helium and exposed to ionizing radiation. Therefore, the radiation tolerance of different types of diodes has been tested at cryogenic temperatures in CERN’s CHARM irradiation test facility during its 2018 run. The forward bias characteristics, the turn-on voltage and the reverse blocking voltage of each diode were measured weekly at 4.2 K and 77 K, as a function of the accumulated radiation dose. The diodes were submitted to a total dose close to 12 kGy and a 1 MeV neutron equivalent fluence of 2.2×1014 cm−2. After the end of the irradiation program the annealing behavior of the diodes was tested by increasing the temperature slowly to 293 K. This paper describes the experimental setup, the measurement procedure and the analysis of the measurements performed during the irradiation program as well as the results of the annealing study
Experimental Setup to Characterize the Radiation Hardness of Cryogenic Bypass Diodes for the HL-LHC Inner Triplet Circuits
For the high luminosity upgrade of the Large Hadron Collider (LHC), it is planned to replace the existing triplet quadrupole magnets with Nb₃Sn quadrupole magnets, which provide a comparable integrated field gradient with a significantly increased aperture. These magnets will be powered through a novel superconducting link based on MgB₂ cables. One option for the powering layout of this triplet circuit is the use of cryogenic bypass diodes, where the diodes are located inside an extension to the magnet cryostat and operated in superfluid helium. Hence, they are exposed to radiation. For this reason the radiation hardness of existing LHC type bypass diodes and more radiation tolerant prototype diodes needs to be tested up to the radiation doses expected at their planned position during their lifetime. A first irradiation test is planned in CERN's CHARM facility starting in spring 2018. Therefore, a cryo-cooler based cryostat to irradiate and test LHC type diodes in-situ has been designed and constructed. This paper will describe the properties of the sample diodes, the experimental roadmap and the setup installed in CHARM. Finally, the first measurement results will be discussed
- …