Two SMA-Actuated Miniature Mechanisms

The figures depict two miniature mechanisms actuated by strips made of shape-memory alloy (SMA). A typical SMA is a nickel-titanium alloy known by the trade name "Flexinol" or "Nitinol." In preparation for a typical application, a suitably sized and shaped piece of an SMA is deformed by a predetermined amount at the lower of two operating temperatures, then mounted in a mechanism. When stroking of the mechanism in one direction is desired, the piece of SMA is heated above a transition temperature to make it return to the "remembered" undeformed state. When stroking of the mechanism in the opposite direction is desired, the SMA is cooled below the transition temperature to make it return to the deformed state. Also, the SMA alloy chosen for a specific application is one that has a transition temperature somewhat above the ambient temperature, so that stroking in one direction or the opposite direction can be achieved by heating the SMA, or refraining from heating the SMA, respectively, above the transition temperature. In the present mechanisms as in typical other SMA mechanisms, the heating is effected by electric currents applied via electrical contacts at the ends of the SMA strips. The purpose served by the mechanism of Figure 1 is to lock or release a flexible latch attachment. In preparation for use in this mechanism, two initially straight SMA strips are deformed into curved springs that, when mounted in the mechanism at ambient temperature, clamp the knob at the lower end of the flexible latch attachment. When heated above their transition temperature by an electric current, the SMA strips return to their original straight configuration, thereby releasing the knob. This mechanism is redundant in the sense that as long as at least one of the two SMA strips straightens when commanded to do so, the knob is released. The mechanism of Figure 2 is suited to any of a variety of applications in which there are requirements for a small mechanism that affords lowtorque rotary actuation through a finite angular range. As shown here, the mechanism is used to rotate a coverlatch pin to a release position. In this case, a straight and flat SMA strip is torsionally deformed to a twist angle of about 90deg by use of a torsion bias spring. When the SMA strip is heated, it rotates to its original straight and flat condition

Miniature Linear Actuator for Small Spacecraft

A report discusses the development of a kit of mechanisms intended for use aboard future spacecraft having masses between 10 and 100 kg. The report focuses mostly on two prototypes of one of the mechanisms: a miniature linear actuator based on a shape-memory-alloy (SMA) wire. In this actuator, as in SMA-wire actuators described previously in NASA Tech Briefs, a spring biases a moving part toward one limit of its stroke and is restrained or pulled toward the other limit of the stroke by an SMA wire, which assumes a slightly lesser or greater "remembered" length, depending on whether or not an electric current is applied to the wire to heat it above a transition temperature. Topics addressed in the report include the need to develop mechanisms like these, the general approach to be taken in designing SMA actuators, tests of the two prototypes of the miniature linear actuators, and improvements in the second prototype over the first prototype resulting in reduced mass and increased stroke. The report also presents recommendations for future development, briefly discusses problems of tolerances and working with small parts, states a need for better understanding of behaviors of SMAs, and presents conclusions

Modeling and Simulation of the Second-Generation Orion Crew Module Air Bag Landing System

Air bags were evaluated as the landing attenuation system for earth landing of the Orion Crew Module (CM). Analysis conducted to date shows that airbags are capable of providing a graceful landing of the CM in nominal and off-nominal conditions such as parachute failure, high horizontal winds, and unfavorable vehicle/ground angle combinations, while meeting crew and vehicle safety requirements. The analyses and associated testing presented here surround a second generation of the airbag design developed by ILC Dover, building off of relevant first-generation design, analysis, and testing efforts. In order to fully evaluate the second generation air bag design and correlate the dynamic simulations, a series of drop tests were carried out at NASA Langley s Landing and Impact Research (LandIR) facility in Hampton, Virginia. The tests consisted of a full-scale set of air bags attached to a full-scale test article representing the Orion Crew Module. The techniques used to collect experimental data, develop the simulations, and make comparisons to experimental data are discussed