Влияние обработки высокоинтенсивным потоком ионов Zr на структуру и механические свойства высокопрочной стали 30ХГСН2А

Исследование структуры модифицированного поверхностного слоя высокопрочной стали30ХГСН2А проводили с помощью оптической просвечивающей электронной микроскопии, а так жеметодов рентгеновской дифракции. Испытания на статическое и циклическое растяжение проводилидля стальных образцов в состоянии поставки, а так же после модификации поверхностного слояпотоком ионов Zr

Influence of ion-beam treatment on structure and defor-mation resistance of 12Cr1MoV steel under static, cyclic and dynamic loading

Features of modification of structure and properties of 12Cr1MoV steel subjected to ion-beam irradiation by zirconium ion beam have been investigated with the use of optical and electron microscopy, and microhardness measurement. It was shown that after the treat-ment the modification occurs across the entire cross-section of specimens with the thickness of 1 mm. Changes in mechanical properties of these specimens under static, cyclic and impact loading were interpreted in terms of identified structure modifications

Structural levels of deformation and failure of heat-resistant 12Cr1MoV steel modified by vacuum arc treatment by Zr{+} ion beam

Study of structural changes occurring in the surface layer modified by ion-beam irradiation was carried out by means of optical, scanning and transmission electron microscopy. It was shown that irradiation induces the structure modification not only in the surface layer, but along the entire cross section of 1 mm thick specimens. It was elucidated that the complex pattern of structural changes is responsible for the pronounced variation of mechanical properties taking place under static tension and cyclic alternating bending

Influence of stress concentrator shape and testing temperature on impact fracture regularities of pipeline steel

The structure and impact toughness of the pipeline 17Mn1Si steel have been studied. The main attention was paid to the analysis of various conditions of stress concentration under dynamic loadings. The process of strain localization with increasing stress state stiffness at the tip of the concentrator with decreasing testing temperature was investigated. Impact loading diagrams for specimens with various stress concentrator shapes were registered and analyzed

Increasing Fatigue LIfe of 09Mn2Si Steel by means of High-Temperature Multistep Helical Rolling

The effect of high temperature helical rolling (HR) on structure and fatigue life of 09Mn2Si pipe steel has been studied. With the use of transmission electron microscopy there was revealed that rolling gives rise to refinement of ferrite grains and cracking (fracturing) of cementite plates within the pearlite phase. The effect manifests itself to the greatest extent in the surface layer where due to the rolling the level of plastic deformation was the highest. Data of microhardness measurements confirms the gradient pattern of strain hardening over the cross section during the HR occurs while the most intensive microhardness increasing take place at the depth of up to 3 mm. According to the mechanical testing results the helical rolling of 09Mn2Si steel gives rise to increasing the level of deforming stress at the yield plateau as well as the proportionality limit with a general decrease in the relative elongation. At the same time, despite the strain hardening resulting from the helical rolling the mechanisms of plastic deformation which manifest themselves in the form of parabolic hardening with a smooth decrease in the flow stress level after neck formation are preserved in the steel. During the cyclic tension the number of cycles prior to failure increases from 2.5 to 3.8 times that depends on the location of specimens' cutting from the rolled rod. The highest improvement in fatigue fracture resistance is registered for specimens cut out from the core of the rolled rods

Increasing Fatigue LIfe of 09Mn2Si Steel by means of High-Temperature Multistep Helical Rolling

The effect of high temperature helical rolling (HR) on structure and fatigue life of 09Mn2Si pipe steel has been studied. With the use of transmission electron microscopy there was revealed that rolling gives rise to refinement of ferrite grains and cracking (fracturing) of cementite plates within the pearlite phase. The effect manifests itself to the greatest extent in the surface layer where due to the rolling the level of plastic deformation was the highest. Data of microhardness measurements confirms the gradient pattern of strain hardening over the cross section during the HR occurs while the most intensive microhardness increasing take place at the depth of up to 3 mm. According to the mechanical testing results the helical rolling of 09Mn2Si steel gives rise to increasing the level of deforming stress at the yield plateau as well as the proportionality limit with a general decrease in the relative elongation. At the same time, despite the strain hardening resulting from the helical rolling the mechanisms of plastic deformation which manifest themselves in the form of parabolic hardening with a smooth decrease in the flow stress level after neck formation are preserved in the steel. During the cyclic tension the number of cycles prior to failure increases from 2.5 to 3.8 times that depends on the location of specimens' cutting from the rolled rod. The highest improvement in fatigue fracture resistance is registered for specimens cut out from the core of the rolled rods

Structure and Properties of Coatings Formed by Detonation Spraying of Titanium Powder

Structure and properties of the coatings formed by detonation spraying of titanium powder have been studied at varying the deposition parameters (nature of carrier gas, spraying distance, O[2]/C[2]H[2] ratio, and the volume of explosive mixture). It is shown that when air is used as the carrier gas the primary strengthening by the titanium oxide phases is realized. When nitrogen is introduced into the explosive mixture, a more complicated mechanism of hardening is realized due to the formation of titanium oxides, carbides, oxynitrides and carbonitrides. The aspects of employing the revealed "rational" modes of the detonation spraying for formation of protective composite coatings based on titanium possessing a complex of improved physical and mechanical properties are discussed