6 research outputs found
Study of Influence of Alloying Elements on Strength and Thermal Resistance of Electric Engineering Aluminum Alloys
В статье проведен сравнительный анализ влияния циркония, железа и РЗМ на структуру и
свойства деформированных полуфабрикатов из алюминиевых сплавов. Установлено, что
для достижения свойств катанки, заданных в АSТМ B941–05, требуется на порядок меньше
циркония по сравнению с РЗМ. Проведены высокотемпературные испытания сплавов Al-Zr-Fe
и Al-РЗМ для поиска наиболее перспективных легирующих элементов для производства
термостойких проводовIn the article a comparison analysis of Zr, Fe and rare-earth metals (REM) influence on the
structure and properties of deformable semi-finished products from aluminium alloys was
investigated. It was established that to achieve properties of wire rod, demanded by ASTM B941–
05, the less Zr content is needed in compare with REM. High temperature experiments of Al-Zr-Fe
и Al-REM alloys were performed to find more perspective alloying elements for the heat resistant
wire productio
Development of Annealing Conditions wire Rod Alloy of Al-Zr System to Reach Required Properties
В статье рассмотрено влияние непрерывного и ступенчатого отжига на удельное
электрическое сопротивление и механические свойства катанки из малолегированных
сплавов системы Al-Zr для достижения заданного уровня свойств. Установлена связь между
концентрацией легирующих элементов, структурой и свойствами катанки из исследуемых
сплавов. Разработан и рекомендован для внедрения на предприятиях алюминиевой
промышленности ступенчатый режим термической обработки, позволяющий получать
катанку с соответствующим уровнем свойств международного стандартаIn this article was considered the influence of continuous and stepped annealing on resistivity and
mechanical properties of dilute alloy wire rod of a Al-Zr system for reaching of required properties.
There was determined the connection between concentrations of alloying elements, structure and
properties of investigated alloys wire rod. The stepped heat treatment conditions was developed and
recommended for application at the factories of aluminum industry, that allows producing wire rod
with properties of international standard
Investigation of the Structure and Properties of Deformed Semi-Finished Products from Alloys of the Al-REM System Made by the Method of Ingotless Rolling-Extruding
The article presents the investigation results of the structure and properties of rods of aluminum alloys containing zirconium, cerium and lanthanum after ingotless rolling-extruding (IRE) and heat treatment. The patterns of changes in the microstructure, mechanical properties, electrical resistivity depending on the chemical composition of the alloys, processed by the IRE method and various modes of rods annealing are shown. A metallographic analysis of the grain structure of the samples in a deformed state and after annealing performed. The temperatures at which the alloy structure remains stable and maintains the level of operational properties revealed. The effect of chemical composition on the heat resistance of deformed semi-finished products represented. The study made it possible to evaluate the level of properties of experimental alloys after processing by the method of ingotless rolling-extruding and various modes of rods annealing
Study of the Influence of Conditions of Combined Casting and Rolling-Extruding and Two-Stage Annealing on the Structure and Properties of Semi-Finished Electrical Products from an Al–Zr System Alloy
This article presents the results of the study of the joint effect of the processing conditions of the new composition of the Al-Zr system alloy by combined casting and rolling-extruding and two-stage annealing on the structure and properties of round bars used in the manufacture of heat-resistant wires. The research show patterns of changes in the properties, the specific electrical resistance of the bars, depending on different conditions of deformation and heat treatment of aluminum alloy with a content of 0.3% zirconium and 0.2% iron. The results of micro-X-ray spectral analysis and the granular structure of the samples before and after two-stage annealing confirming the stability of the structure after heating and preserving the strength of semi-finished products. Presented parameters of combined casting and rolling-extruding and two-stage annealing for the manufacture of rods from the studied alloy make it possible obtaining good combination of mechanical properties and electrical conductivity
Study of Influence of Alloying Elements on Strength and Thermal Resistance of Electric Engineering Aluminum Alloys
В статье проведен сравнительный анализ влияния циркония, железа и РЗМ на структуру и
свойства деформированных полуфабрикатов из алюминиевых сплавов. Установлено, что
для достижения свойств катанки, заданных в АSТМ B941–05, требуется на порядок меньше
циркония по сравнению с РЗМ. Проведены высокотемпературные испытания сплавов Al-Zr-Fe
и Al-РЗМ для поиска наиболее перспективных легирующих элементов для производства
термостойких проводовIn the article a comparison analysis of Zr, Fe and rare-earth metals (REM) influence on the
structure and properties of deformable semi-finished products from aluminium alloys was
investigated. It was established that to achieve properties of wire rod, demanded by ASTM B941–
05, the less Zr content is needed in compare with REM. High temperature experiments of Al-Zr-Fe
и Al-REM alloys were performed to find more perspective alloying elements for the heat resistant
wire productio
Development of Annealing Conditions wire Rod Alloy of Al-Zr System to Reach Required Properties
В статье рассмотрено влияние непрерывного и ступенчатого отжига на удельное
электрическое сопротивление и механические свойства катанки из малолегированных
сплавов системы Al-Zr для достижения заданного уровня свойств. Установлена связь между
концентрацией легирующих элементов, структурой и свойствами катанки из исследуемых
сплавов. Разработан и рекомендован для внедрения на предприятиях алюминиевой
промышленности ступенчатый режим термической обработки, позволяющий получать
катанку с соответствующим уровнем свойств международного стандартаIn this article was considered the influence of continuous and stepped annealing on resistivity and
mechanical properties of dilute alloy wire rod of a Al-Zr system for reaching of required properties.
There was determined the connection between concentrations of alloying elements, structure and
properties of investigated alloys wire rod. The stepped heat treatment conditions was developed and
recommended for application at the factories of aluminum industry, that allows producing wire rod
with properties of international standard