3 research outputs found
Periodical Maintenance of Forest Roads with a Mobile Stone Crusher
Forest road networks are exposed to damage by traffic, climate, timber harvesting and vegetation. To maintain their functionality, they must be maintained regularly. Periodical maintenance is required when the forest road surface layer is deteriorated and eroded. Well-graded material is required for replacing the forest road surface and often has to be sourced from gravel storage areas, which is costly and requires a large number of truck trips. Therefore, converting non-graded aggregate available on site into well-graded aggregate with a mobile stone crusher is considered a viable alternative. The present study was carried out during a periodical maintenance treatment at the Bavarian State Forest Enterprise and the effect of employing a mobile stone crusher was evaluated with regard to (1) forest road load bearing capacity development during a one-year period posttreatment, (2) particle size distribution of the surface layer material before and after crushing, and (3) its cost compared to other alternatives. Samples were collected pre- and post-operation for particle size distribution analysis, load bearing capacity was measured repeatedly with a light falling weight deflectometer and compared to an untreated reference section and cost of the treatment was compared to two alternatives. The mobile stone crusher was capable of reducing the non-graded to well-graded/close-to-wellgraded material and particle size distributions aligned well with the recommendations for lime-water bonded surfaces. Load bearing capacity exceeded the threshold of 40 MN m–2 (Evd, elastic modulus dynamic) for primary forest roads at all times. It increased significantly after the treatment and remained on a significantly higher level throughout the following year. Absolute and relative increases were higher than on the untreated reference section. The treatment variant involving a mobile stone crusher and material available on site was substantially cheaper (5.31 € m-1) than to supply non-graded (16.29 € m-1) or well-graded (19.82 € m–1) material by truck. Material and transport costs represented 67% and 82% of the total costs in the latter two cases. It can be concluded that mobile stone crushers are capable of producing at least close-to-well-graded forest road surface aggregate and that forest road load bearing capacity can be significantly and lastingly increased at only a part of the costs of the alternatives. A maximum of cost and resource efficiency and environmental soundness can be attained when enough surface aggregate is available on site. If this is not the case, sourcing nongraded material as local as possible is the next best alternative
A Prototype for Automated Delimitation of Work Cycles from Machine Sensor Data in Cable Yarding Operations
The demand for increased efficiency in timber harvesting has traditionally been met by continuous technical improvements in machines and an increase in mechanisation. The use of active and passive sensors on machines enables improvements in aspects such as operational efficiency, fuel consumption and worker safety. Timber harvesting machine manufacturers have used these technologies to improve the maintenance and control of their machines, to select and optimise harvesting techniques and fuel consumption. To a more limited extent, it has also been used to evaluate the time taken to complete tasks. The systematic use of machine sensor data, in a central database or cloud solution is a more recent trend.
Machine data is recorded over long periods of time and at high resolution. This data therefore has considerable potential for scientific investigations. For mechanised timber harvesting operations, this could include a better understanding of the interaction between productivity and operational parameters, which first of all requires an efficient determination of cycle time.
This study was the first to automatically delimitate tower yarder cycle times from machine sensor data. In addition to machine sensor data, cycle times were collected through a traditional manual time and motion study, and cycle times from both studies were compared to a reference cycle time determined from video footage of the yarder in operation.
Based on three days of detailed time study, the total cycle time in the classic manual time (–1.3%) and in the machine sensor data (–1.2%) was only slightly shorter than in the reference study, and the average cycle time did not differ significantly (classic manual time study: –0.08±0.94 min, p=0.997; machine sensor data study: –0.08±0.26 min, p=0.997). However, the accuracy of the machine sensor approach (RMSE=0.92) was more than three times higher than that of the classic manual time study (RMSE=0.27).
With the integration of sensors on forestry machines now being commonplace, this study shows that machine sensor data can be reliably interpreted for time study purposes such as machine or system optimisation. This eliminates the need for manual time study, which can be both cumbersome and dependent on the experience of the observer, and allows long term data sets to be obtained and analysed with comparatively little effort. However, a truly automated time study needs to be supplemented with automated determination of and linkage to other operational parameters, such as yarding and lateral yarding distance or load volume
Measurement of Individual Tree Parameters with Carriage-Based Laser Scanning in Cable Yarding Operations
Introduction: Cable yarding is a technology that enables efficient and sustainable use of timber resources in mountainous areas. Carriages as an integral component of cable yarding systems have undergone significant development in recent decades. In addition to mechanical and functional developments, carriages are increasingly used as carrier platforms for various sensors. The goal of this study was to assess the accuracy of individual standing tree and stand variable estimates obtained by a mobile laser scanning system mounted on a cable yarder carriage.
Methods: Eight cable corridors were scanned across two forest stands. Four different scan variants were conducted, differing in the movement speed of the carriage and the direction of movement during scanning. An algorithm for tree detection, diameter and height estimation was applied to the 3D datasets and evaluated against manual tree measurements.
Results: The analysis of the 3D scans showed that the individual tree parameters strongly depend on the scan variant and the distance of each individual tree to the skyline. This was due to changing 3D point densities and occlusion effects. It turned out that scan variant 1, in which the scan was performed during slow carriage movement downwards and back upwards again, was advantageous. At a distance of 10 m, which is half of the recommended corridor spacing of 20 m for whole tree cable yarding, 95.44% of the trees in stand 1 and 92.16% of the trees in stand 2 could be detected automatically. The corresponding root mean sqare errors of the diameter at breast height estimatimations were 1.59 cm and 2.23 cm, respectively. The root mean square errors of the height measurements were 2.94 m and 4.63 m.
Conclusions: The results of this study can help to further advance the digitization of cable yarding and timber flow from the standing tree to the sawmill. However, this requires further development steps in cable yarder, carriage, and laserscanner technology. Furthermore, there is also a need for more efficient software routines to take the next steps towards precision forestry