Photoluminescence of spray pyrolysis deposited ZnO nanorods

Photoluminescence of highly structured ZnO layers comprising well-shaped hexagonal rods is presented. The ZnO rods (length 500-1,000 nm, diameter 100-300 nm) were grown in air onto a preheated soda-lime glass (SGL) or ITO/SGL substrate by low-cost chemical spray pyrolysis method using zinc chloride precursor solutions and growth temperatures in the range of 450-550°C. We report the effect of the variation in deposition parameters (substrate type, growth temperature, spray rate, solvent type) on the photoluminescence properties of the spray-deposited ZnO nanorods. A dominant near band edge (NBE) emission is observed at 300 K and at 10 K. High-resolution photoluminescence measurements at 10 K reveal fine structure of the NBE band with the dominant peaks related to the bound exciton transitions. It is found that all studied technological parameters affect the excitonic photoluminescence in ZnO nanorods

Comparison of multifractal parameters of surface defects and non-defects

In this study, three different materials (pure tungsten and two tungsten alloys with Fe and Ni dopants), which have been irradiated with a high-temperature deuterium plasma of 20, 25 and 100 plasma shots, are considered. The multifractal characteristics obtained from SEM images are then compared for the same specimens by analysing the distribution of defects and non-defects (non-damaged areas). A valid tendency was found that the brighter the original input image, the more accurate the results obtained when examining a non-damaged surface using multifractal characteristics

A method for producing conductive graphene biopolymer nanofibrous fabrics by exploitation of an ionic liquid dispersant in electrospinning

Owing to its high conductivity, graphene has been incorporated into polymeric nanofibers to create advanced materials for flexible electronics, sensors and tissue engineering. Typically, these graphene-based nanofibers are prepared by electrospinning synthetic polymers, whereas electrospun graphene-biopolymer nanofibers have been rarely reported due to poor compatibility of graphene with biopolymers. Herein, we report a new method for the preparation of graphene-biopolymer nanofibers using the judicious combination of an ionic liquid and electrospinning. Cellulose acetate (CA) has been used as the biopolymer, graphene oxide (GO) nanoparticles as the source of graphene and 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) as the ionic liquid (IL) to create CA-[BMIM]Cl-GO nanofibers by electrospinning for the first time. Moreover, we developed a new route to convert CA-[BMIM]Cl-GO nanofibers to reduced GO nanofibers using hydrazine vapor under ambient conditions to enhance the conductivity of the hybrid nanofibers. The graphene sheets were shown to be uniformly incorporated in the hybrid nanofibers and only 0.43 wt% of GO increase the conductivity of CA-[BMIM]Cl nanofibers by more than four orders of magnitude (from 2.71× 10−7 S/cm to 5.30 × 10−3 S/cm). This ultra-high enhancement opens up a new route for conductive enhancement of biopolymer nanofibers to be used in smart (bio) electronic devices

Western Star, 1912-06-05

The Western Star began publication on Newfoundland's west coast on 4 April 1900, appearing weekly with brief semiweekly periods up to 1952, when it became a daily. As of 17 April 2019 it continues as a free weekly community paper

Primary amines as heterogeneous catalysts in an enantioselective [2,3]-Wittig rearrangement reaction

Summary: A series of heterogeneous catalysts anchored to different polystyrene-based supports has been prepared and applied in an asymmetric [2,3]-Wittig rearrangement reaction of cyclohexanone derivatives. Among them, primary amino acid-derived (aminomethylated)polystyrene-supported catalysts showed excellent reactivity leading to the formation of rearranged products in good enantioselectivities of both diastereomers. Reusability issues connected to the deactivation of the catalyst were proved to be dependent on the end-capping strategy chosen for the blocking of the unreacted active sites of the resin. This issue of end-capping has not previously been in focus. Using bulkier pivaloyl end-capping moiety, we were able to recycle the catalyst in six consecutive cycles with only marginal deceleration of the reaction. Moreover, the epimerization of the product that occurred while conducting a rearrangement reaction in the presence of a homogeneous catalyst was almost fully eliminated by switching the catalytic system to heterogeneous

Metal-Matrix Hardmetal/Cermet Reinforced Composite Powders for Thermal Spray

Recycling of materials is becoming increasingly important as industry response to public demands, that resources must be preserved and environment protected. To produce materials competitive in cost with primary product, secondary producers have to pursue new technologies and other innovations. For these purposes different recycling technologies for composite materials (oxidation, milling, remelting etc) are widely used. The current paper studies hardmetal/cermet powders produced by mechanical milling technology. The following composite materials were studied: Cr3C2-Ni cermets and WC-Co hardmetal. Different disintegrator milling systems for production of powders with determined size and shape were used. Chemical composition of produced powders was analysed.  To estimate the properties of recycled hardmetal/cermet powders, sieving analysis, laser granulometry and angularity study were conducted. To describe the angularity of milled powders, spike parameter–quadric fit (SPQ) was used and experiments for determination of SPQ sensitivity and precision to characterize particles angularity were performed. Images used for calculating SPQ were taken by SEM processed with Omnimet Image Analyser 22. The graphs of grindability and angularity were composed. Composite powders based on Fe- and Ni-self-fluxing alloys for thermal spray (plasma and HVOF) were produced. Technological properties of powders and properties of thermal sprayed coatings from studied powders were investigated. The properties of spray powders reinforced with recycled hardmetal and cermet particles as alternatives for cost-sensitive applications were demonstrated.DOI: http://dx.doi.org/10.5755/j01.ms.18.1.1348</p

Influence of Protic Ionic Liquid-Based Flame Retardant on the Flammability and Water Sorption of Alkalized Hemp Fiber-Reinforced PLA Composites

This article investigates the effects of combining a novel protic ionic liquid-based fire retardant (FR) with alkalized hemp fiber. A pivotal importance of this study refers to the hydrophilic properties and limits regarding poor thermal resistance of green composites where standard guidelines for fire risks are crucial. Although it is well-studied that alkalization is essential for green composite’s moisture and mechanical durability, research on the flammability of such a combined treatment for natural fiber-reinforced biopolymer composites is lacking. The alkaline treatment used in the current study follows a process already studied as optimal, particularly for the selected hemp fiber. The fire performance was examined using a bench scale approach based on self and piloted ignition from cone calorimeter tests. The result from the Fourier-transform infrared analysis of the hemp fiber confirms phosphorylation following the fire-retardant treatment, which was visible from the morphological examination with scanning electron microscope. The presence of FR in the composites led to impactful moisture sorption. However, the FR composites demonstrated an enhanced response to fire, indicating potential use as a Class B standard for building construction, and hazard level 3 (HL3) classification as an interior material in vehicles, provided the problem of high emission of smoke is mitigated

Effect of Solution Spray Rate on the Properties of Chemically Sprayed ZnO:In Thin Films

ZnO:In thin films were grown from 100 mL of spray solution on glass substrates by chemical spray at Ts=400°C using solution spray rates of 0.5–6.7 mL/min. Zinc acetate and indium(III)chloride were used as Zn and In sources, respectively, with [In]/[Zn] = 3 at.%. Independent of solution spray rate, the crystallites in ZnO:In films grow preferentially in the (101) plane parallel to the substrate. The solution spray rate influences the surface morphology, grain size, film thickness, and electrical and optical properties. According to SEM and AFM studies, sharp-edged pyramidal grains and canvas-resembling surfaces are characteristic of films grown at spray rates of 0.5 and 3.3 mL/min, respectively. To obtain films with comparable film thickness and grain size, more spray solution should be used at low spray rates. The electrical resistivity of sprayed ZnO:In films is controlled by the solution spray rate. The carrier concentration increases from 2·1019 cm−3 to 1·1020 cm−3 when spray rate is increased from 0.5 mL/min to 3.3 mL/min independent of the film thickness; the carrier mobilities are always lower in slowly grown films. Sprayed ZnO:In films transmit 75–80% of the visible light while the increase in solution spray rate from 0.5 mL/min to 3.3 mL/min decreases the transmittance in the NIR region and increases the band gap in accordance with the increase in carrier concentration. Lower carrier concentration in slowly sprayed films is likely due to the indium oxidation

Wear Resistant Thermal Sprayed Composite Coatings Based on Iron Self-Fluxing Alloy and Recycled Cermet Powders

Thermal spray and WC-Co based coatings are widely used in areas subjected to abrasive wear. Commercial  cermet thermal spray powders for HVOF are relatively expensive. Therefore applying these powders in cost-sensitive areas like mining and agriculture are hindered. Nowadays, the use of cheap iron based self-fluxing alloy powders for thermal spray is limited. The aim of this research was to study properties of composite powders based on self-fluxing alloys and recycled cermets and to examine the properties of thermally sprayed (HVOF) coatings from composite powders based on iron self-fluxing alloy and recycled cermet powders (Cr₃C₂-Ni and WC-Co). To estimate the properties of  recycled cermet powders, the sieving analysis, laser granulometry and morphology were conducted. For deposition of coatings High Velocity Oxy-Fuel spray was used. The structure and composition of powders and coatings were estimated by SEM and XRD methods. Abrasive wear performance of coatings was determined and compared with wear resistance of coatings from commercial powders. The wear resistance of thermal sprayed coatings from self-fluxing alloy and recycled cermet powders at abrasion is comparable with wear resistance of coatings from commercial expensive spray powders and may be an alternative in tribological applications in cost-sensitive areas.<p>DOI: <a href="http://dx.doi.org/10.5755/j01.ms.18.1.1338">http://dx.doi.org/10.5755/j01.ms.18.1.1338</a></p