Impeller-Induced Rotor-Dynamic Forces

The flow through and around the rotor of a turbomachine exerts a force on the rotor and, hence, rotor shaft and bearing system. In some circumstances this force may lead to excitation of shaft whirl in the direction of impeller rotation. Recent international research of this phenomenon is briefly reviewed; these findings suggest that turbomachines intended to operate well above the first critical speed should take the effect into account

Siphonaptera Records and Host Associations From the Central and Eastern Upper Peninsula of Michigan

Fleas were collected from birds and mammals over a five year period in four upper peninsula counties. Identified specimens were compared to published records of distribution for the parasite species and its host species, and only those records which are new county distributions for host or parasite are listed. Four new host records for Michigan, four new flea distribution records for the upper peninsula, and 26 new county records are listed

Forces on Centrifugal Pump Impellers

Forces are exerted on a centrifugal pump impeller, due to the asymmetry of the flow caused by the volute of diffuser, and to the motion of the center of the impeller whenever the shaft whirls. Recent work in the measurement of these forces as a function of the whirl speed to shaft speed ratio, and the influence of the volute, is reviewed. These forces may be decomposed into a steady force, a static stiffness matrix, a damping matrix and an inertia matrix. It is shown that for centrifugal pumps of the moderate specific speed typical of boiler feed stages, there is a region of potential shaft vibration excitation from the hydrodynamic forces if the operating speed is well above the first flexural critical speed

The Influence of Swirl Brakes on the Rotordynamic Forces Generated by Discharge-to-Suction Leakage Flows in Centrifugal Pumps

Increasing interest has been give to swirl brakes as a means of reducing destabilizing rotordynamic forces due to leakage flows in new high speed rocket turbopumps. Although swirl brakes have been used successfully in practice (such as with the Space Shuttle HPOTP), no experimental test until now have been performed to demonstrate their beneficial effect over a range of leakage flow rates. The present study investigates the effect of swirl brakes on rotordynamic forces generated by discharge-to-suction leakage flows in the annulus of shrouded centrifugal pumps over a range of subsynchronous whirl ratios and various leakage flow rates. In addition, the effectiveness of swirl brakes in the presence of leakage inlet (pump discharge) swirl is also demonstrated. The experimental data demonstrates that with the addition of swirl brakes a significant reduction in the destabilizing tangential force for lower flow rates is achieved. At higher flow rates, the brakes are detrimental. In the presence of leakage inlet swirl, brakes were effective over all leakage flow rates tested in reducing the range of whirl frequency ratio for which the tangential force is destabilizing

External stress-corrosion cracking of a 1.22-m-diameter type 316 stainless steel air valve

An investigation was conducted to determine the cause of the failure of a massive AISI Type 316 stainless steel valve which controlled combustion air to a jet engine test facility. Several through-the-wall cracks were present near welded joints in the valve skirt. The valve had been in outdoor service for 18 years. Samples were taken in the cracked regions for metallographic and chemical analyses. Insulating material and sources of water mist in the vicinity of the failed valve were analyzed for chlorides. A scanning electron microscope was used to determine whether foreign elements were present in a crack. On the basis of the information generated, the failure was characterized as external stress-corrosion cracking. The cracking resulted from a combination of residual tensile stress from welding and the presence of aqueous chlorides. Recommended countermeasures are included

Optical Spin Initialization and Non-Destructive Measurement in a Quantum Dot Molecule

The spin of an electron in a self-assembled InAs/GaAs quantum dot molecule is optically prepared and measured through the trion triplet states. A longitudinal magnetic field is used to tune two of the trion states into resonance, forming a superposition state through asymmetric spin exchange. As a result, spin-flip Raman transitions can be used for optical spin initialization, while separate trion states enable cycling transitions for non-destructive measurement. With two-laser transmission spectroscopy we demonstrate both operations simultaneously, something not previously accomplished in a single quantum dot.Comment: Accepted for publication in Phys. Rev. Let