4 research outputs found
Combined EXAFS, XRD, DRIFTS, and DFT Study of Nano Copper Based Catalysts for CO2 Hydrogenation
Highly monodispersed CuO nanoparticles (NPs) were synthesized via continuous hydrothermal flow synthesis (CHFS) and then tested as catalysts for CO2 hydrogenation. The catalytic behavior of unsupported 11 nm sized nanoparticles from the same batch was characterized by diffuse reflectance infrared fourier transform spectroscopy (DRIFTS), extended X-ray absorption fine structure (EXAFS), X-ray diffraction (XRD), and catalytic testing, under CO2/H2 in the temperature range 25–500 °C in consistent experimental conditions. This was done to highlight the relationship among structural evolution, surface products, and reaction yields; the experimental results were compared with modeling predictions based on density functional theory (DFT) simulations of the CuO system. In situ DRIFTS revealed the formation of surface formate species at temperatures as low as 70 °C. DFT calculations of CO2 hydrogenation on the CuO surface suggested that hydrogenation reduced the CuO surface to Cu2O, which facilitated the formation of formate. In situ EXAFS supported a strong correlation between the Cu2O phase fraction and the formate peak intensity, with the maxima corresponding to where Cu2O was the only detectable phase at 170 °C, before the onset of reduction to Cu at 190 °C. The concurrent phase and crystallite size evolution were monitored by in situ XRD, which suggested that the CuO NPs were stable in size before the onset of reduction, with smaller Cu2O crystallites being observed from 130 °C. Further reduction to Cu from 190 °C was followed by a rapid decrease of surface formate and the detection of adsorbed CO from 250 °C; these results are in agreement with heterogeneous catalytic tests where surface CO was observed over the same temperature range. Furthermore, CH4 was detected in correspondence with the decomposition of formate and formation of the Cu phase, with a maximum conversion rate of 2.8% measured at 470 °C (on completely reduced copper), supporting the indication of independent reaction pathways for the conversion of CO2 to CH4 and CO that was suggested by catalytic tests. The resulting Cu NPs had a final crystallite size of ca. 44 nm at 500 °C and retained a significantly active surface
Arc Synthesis, Crystal Structure, and Photoelectrochemistry of Copper(I) Tungstate
A little-studied p-type ternary oxide semiconductor, copper(I) tungstate (Cu2WO4), was assessed by a combined theoretical/experimental approach. A detailed computational study was performed to solve the long-standing debate on the space group of Cu2WO4, which was determined to be triclinic P1. Cu2WO4 was synthesized by a time-efficient, arc-melting method, and the crystalline reddish particulate product showed broad-band absorption in the UV–visible spectral region, thermal stability up to ∼260 °C, and cathodic photoelectrochemical activity. Controlled thermal oxidation of copper from the Cu(I) to Cu(II) oxidation state showed that the crystal lattice could accommodate Cu2+ cations up to ∼260 °C, beyond which the compound was converted to CuO and CuWO4. This process was monitored by powder X-ray diffraction and X-ray photoelectron spectroscopy. The electronic band structure of Cu2WO4 was contrasted with that of the Cu(II) counterpart, CuWO4 using spin-polarized density functional theory (DFT). Finally, the compound Cu2WO4 was determined to have a high-lying (negative potential) conduction band edge underlining its promise for driving energetic photoredox reactions
Combined Experimental and Theoretical Study of the Competitive Absorption of CO2 and NO2 by a Superbase Ionic Liquid
A superbase ionic liquid (IL), trihexyltetradecylphosphonium benzimidazolide ([P66614][Benzim]), is investigated for the capture of CO2 in the presence of NO2 impurities. The effect of the waste gas stream contaminant on the ability of the IL to absorb simultaneously CO2 is demonstrated using novel measurement techniques, including a mass spectrometry breakthrough method and in situ infrared spectroscopy. The findings show that the presence of an industrially relevant concentration of NO2 in a combined feed with CO2 has the effect of reducing the capacity of the IL to absorb CO2 efficiently by ∼60% after 10 absorption–desorption cycles. This finding is supported by physical property analysis (viscosity, 1H and 13C NMR, and X-ray photoelectron spectroscopy) and spectroscopic infrared characterization, in addition to density functional theory (DFT) calculations, to determine the structure of the IL-NO2 complex. The results are presented in comparison with another flue gas component, NO, demonstrating that the absorption of NO2 is more favorable, thereby hindering the ability of the IL to absorb CO2. Significantly, this work aids understanding of the effects that individual components of flue gas have on CO2 capture sorbents, through studying a contaminant that has received limited interest previously