Electronic and Magnetic Properties of Electron-doped Superconductor, Sm_{1.85}Ce_{0.15}CuO_{4-delta}

Temperature-dependent magnetization (M(T)) and specific heat (C_p(T)) measurements were carried out on single crystal Sm_{1.85}Ce_{0.15}CuO_{4-delta} (T_c = 16.5 K). The magnetic anisotropy in the static susceptibility, chi {equiv} M/H, is apparent not only in its magnitude but also in its temperature dependence, with chi_{perp} for H{perp}c larger than chi_{parallel} for H{parallel}c. For both field orientations, chi does not follow the Curie-Weiss behavior due to the small energy gap of the J = 7/2 multiplet above the J = 5/2 ground-state multiplet. However, with increasing temperature, chi_{parallel}(T) exhibits a broad minimum near 100 K and then a slow increase while chi_{perp}(T) shows a monotonic decrease. A sharp peak in C_p(T) at 4.7 K manifests an antiferromagnetic ordering. The electronic contribution, gamma, to C_p(T) is estimated to be gamma = 103.2 (7) mJ/moleSmK^2. The entropy associated with the magnetic ordering is much smaller than Rln2, where R is the gas constant, which is usually expected for the doublet ground state of Sm^{+3}. The unusual magnetic and electronic properties evident in M(T) and C_p(T) are probably due to a strong anisotropic interaction between conduction electrons and localized electrons at Sm^{+3} sites.Comment: 5 pages, 5 encapsulated postscript figures, late

Design and experimental evaluation of flextensional-cantilever based piezoelectric transducers for flow energy harvesting

Cantilever type piezoelectric harvesters, such as bimorphs, are typically used for vibration induced energy harvesting. However, a major drawback of a piezoelectric bimorph is its brittle nature in harsh environments, precipitating short life-times as well as output power degradation. The emphasis in this work is to design robust, highly efficient piezoelectric harvesters that are capable of generating electrical power in the milliwatt range. Various harvesters were modeled, designed and prototyped, and the flextensional actuator based harvester, where the metal cantilever is mounted and coupled between two flextensional actuators, was found to be a viable alternative to the cantilever type piezoelectric harvesters. Preliminary tests show that these devices equipped with 5x5x36 mm two piezoelectric PZT stacks can produce greater than 50 mW of power under air flow induced vibrations

A Case of Right Sided Aortic Arch Combined with Atrial Septal Defect

Right sided aortic arch is an uncommon congenital anomaly. It can be classified into three types, depending on the left aortic arch's degenerating pattern and the branching pattern of the great vessels. It can be associated with major congenital heart disease, depending on the type of right sided aortic arch. We report a case of an 18-years-old female who has right sided aortic arch with atrial septal defect (ASD). In our case, the patient had a right sided aortic arch and aberrant left subclavian artery, also she had ASD (ostium secundum) and moderate tricuspid regurgitation with pulmonary hypertension. The patient was successfully performed patch closure of ASD and tricuspid valve annuloplasty via midline sternotomy. The patient had uneventful postoperative course

Piezoelectric Energy Harvesting in Internal Fluid Flow

We consider piezoelectric flow energy harvesting in an internal flow environment with the ultimate goal powering systems such as sensors in deep oil well applications. Fluid motion is coupled to structural vibration via a cantilever beam placed in a converging-diverging flow channel. Two designs were considered for the electromechanical coupling: first; the cantilever itself is a piezoelectric bimorph; second; the cantilever is mounted on a pair of flextensional actuators. We experimentally investigated varying the geometry of the flow passage and the flow rate. Experimental results revealed that the power generated from both designs was similar; producing as much as 20 mW at a flow rate of 20 L/min. The bimorph designs were prone to failure at the extremes of flow rates tested. Finite element analysis (FEA) showed fatigue failure was imminent due to stress concentrations near the bimorph’s clamped region; and that robustness could be improved with a stepped-joint mounting design. A similar FEA model showed the flextensional-based harvester had a resonant frequency of around 375 Hz and an electromechanical coupling of 0.23 between the cantilever and flextensional actuators in a vacuum. These values; along with the power levels demonstrated; are significant steps toward building a system design that can eventually deliver power in the Watts range to devices down within a well

Sample Handling and Instruments for the In-Situ Exploration of Ice-Rich Planets

NASA's key science goals for the exploration of the solar system seek a better understanding of the formation and evolutionary processes that have shaped planetary bodies and emphasize the search for habitable environments. Efforts are also made to detect and quantify resources that could be used for the support of human exploration. These themes call for chemistry and physical property observations that may be best approached by in situ measurements. NASA's planetary missions have progressively evolved from remote reconnaissance to in situ exploration with the ultimate goal to return samples. This chapter focuses on the techniques, available or in development, for advanced geophysical and chemical characterization of icy bodies, especially Mars polar areas, Enceladus, Titan, Europa, and Ceres. These astrobiological targets are the objects of recent or ongoing exploration whose findings are driving the formulation of new missions that involve in situ exploration. After reviewing the overall objectives of icy body exploration (Section 9.1) we describe key techniques used for addressing these objectives from surface platforms via geophysical observations (Section 9.2) and chemical measurements (Section 9.3)

Late Simultaneous Presentation of Left Ventricular Pseudoaneurysm and Tricuspid Regurgitation after Blunt Chest Trauma

A 32-yr-old man developed progressive exertional dyspnea 4 yr after blunt chest trauma due to an automobile accident. Two-dimensional echocardiography and computed-tomographic coronary angiography demonstrated a large pseudoaneurysm of the left ventricle and severe tricuspid regurgitation. The patient underwent successful surgical exclusion of the pseudoaneurysm by endoaneurysmal patch closure and repair of the tricuspid valve regurgitation. To the best of our knowledge, this is the first case of these 2 different pathologies presenting late simultaneously after blunt chest trauma and successful surgical repairs in the published literature