Synthesis of titanate nanostructures using amorphous precursor material and their adsorption/photocatalytic properties

This paper reports on a new and swift hydrothermal chemical route to prepare titanate nanostructures (TNS) avoiding the use of crystalline TiO2 as starting material. The synthesis approach uses a commercial solution of TiCl3 as titanium source to prepare an amorphous precursor, circumventing the use of hazardous chemical compounds. The influence of the reaction temperature and dwell autoclave time on the structure and morphology of the synthesised materials was studied. Homogeneous titanate nanotubes with a high length/diameter aspect ratio were synthesised at 160^{\circ}C and 24 h. A band gap of 3.06\pm0.03 eV was determined for the TNS samples prepared in these experimental conditions. This value is red shifted by 0.14 eV compared to the band gap value usually reported for the TiO2 anatase. Moreover, such samples show better adsorption capacity and photocatalytic performance on the dye rhodamine 6G (R6G) photodegradation process than TiO2 nanoparticles. A 98% reduction of the R6G concentration was achieved after 45 minutes of irradiation of a 10 ppm dye aqueous solution and 1 g/L of TNS catalyst.Comment: 29 pages, 10 figures, accepted for publication in Journal of Materials Scienc

Ultrahigh-Field MRI in Human Ischemic Stroke – a 7 Tesla Study

INTRODUCTION: Magnetic resonance imaging (MRI) using field strengths up to 3 Tesla (T) has proven to be a powerful tool for stroke diagnosis. Recently, ultrahigh-field (UHF) MRI at 7 T has shown relevant diagnostic benefits in imaging of neurological diseases, but its value for stroke imaging has not been investigated yet. We present the first evaluation of a clinically feasible stroke imaging protocol at 7 T. For comparison an established stroke imaging protocol was applied at 3 T. METHODS: In a prospective imaging study seven patients with subacute and chronic stroke were included. Imaging at 3 T was immediately followed by 7 T imaging. Both protocols included T1-weighted 3D Magnetization-Prepared Rapid-Acquired Gradient-Echo (3D-MPRAGE), T2-weighted 2D Fluid Attenuated Inversion Recovery (2D-FLAIR), T2-weighted 2D Fluid Attenuated Inversion Recovery (2D-T2-TSE), T2* weighted 2D Fast Low Angle Shot Gradient Echo (2D-HemoFLASH) and 3D Time-of-Flight angiography (3D-TOF). RESULTS: The diagnostic information relevant for clinical stroke imaging obtained at 3 T was equally available at 7 T. Higher spatial resolution at 7 T revealed more anatomical details precisely depicting ischemic lesions and periinfarct alterations. A clear benefit in anatomical resolution was also demonstrated for vessel imaging at 7 T. RF power deposition constraints induced scan time prolongation and reduced brain coverage for 2D-FLAIR, 2D-T2-TSE and 3D-TOF at 7 T versus 3 T. CONCLUSIONS: The potential of 7 T MRI for human stroke imaging is shown. Our pilot study encourages a further evaluation of the diagnostic benefit of stroke imaging at 7 T in a larger study

Stimulus responsive graphene scaffolds for tissue engineering

Tissue engineering (TE) is an emerging area that aims to repair damaged tissues and organs by combining different scaffold materials with living cells. Recently, scientists started to engineer a new generation of nanocomposite scaffolds able to mimic biochemical and biophysical mechanisms to modulate the cellular responses promoting the restoration of tissue structure or function. Due to its unique electrical, topographical and chemical properties, graphene is a material that holds a great potential for TE, being already considered as one of the best candidates for accelerating and guiding stem cell differentiations. Although this is a promising field there are still some challenges to overcome, such as the efficient control of the differentiation of the stem cells, especially in graphene-based microenvironments. Hence, this chapter will review the existing research related to the ability of graphene and its derivatives (graphene oxide and reduced graphene oxide) to induce stem cell differentiation into diverse lineages when under the influence of electrical, mechanical, optical and topographic stimulations

Atmospheric plasma sprayed (APS) coatings of Al2O3-TiO2 system for photocatalytic application

International audienceThe goal of this study is to examine the photocatalytic ability of coatings produced by atmospheric plasma spraying (APS). The plasma gun used is a common gas-stabilized plasma gun (GSP) working with a d.c. current and a mixture of argon and hydrogen as plasma-forming gas. The TiO2 powders are particles of about 100 nm which were agglomerated to a mean size of about 55 m, suitable for spraying. Composition of the commercial powder is 13 wt% of TiO2 in Al2O3, whereas also in-house prepared powder with the same nominal composition but with agglomerated TiO2 and conventional fused and crushed Al2O3 was sprayed. The feedstock materials used for this purpose are -alumina and anatase titanium dioxide. The coatings are analyzed by scanning electron microscopy (SEM), energy dispersion probe (EDS) and X-ray diffraction. Photocatalytic degradation of acetone is quantified for various coatings. All plasma sprayed coatings show a lamellar structure on cross section, as typical for this process. Anatase titania from feedstock powder is converted into rutile titania and -alumina partly to -alumina. Coatings are proven to catalyse the acetone decomposition when irradiated by UV rays