How Do States' Safety Net Policies Affect Poverty?

Using Georgia, Illinois, and Massachusetts as illustrative examples, examines how states' narrow, medium, or broad policies on cash, non-cash, and tax elements of the safety net affect poverty rates among non-elderly adults and children

Development of Ultra-Efficient Electric Motors Final Technical Report Covering work from April 2002 through September 2007

High temperature superconducting (HTS) motors offer the potential for dramatic volume and loss reduction compared to conventional, high horspower, industrial motors. This report is the final report on the results of eight research tasks that address some of the issues related to HTS motor development that affect motor efficiency, cost, and reliability

Activation Volume for Arsenic Diffusion in Germanium

We have measured the effect of pressure on As diffusion in Ge. Diffusion anneals on ion-implanted samples were carried out in a high-temperature diamond anvil cell using fluid argon as a clean, hydrostatic pressure medium. At 575 °C over the pressure range 0.1–4 GPa, pressure slightly enhances the diffusivity, characterized by an activation volume of –1.7 ± 1.4 cm3/mole or –0.12 ± 0.10 times the atomic volume. The results call into question the prevailing view that diffusion of groups III, IV, and V elements are mediated entirely by vacancies. If diffusion of As is mediated entirely by vacancies then either the vacancy formation volume must be unexpectedly low or the energy of vacancy migration must be unexpectedly high.Engineering and Applied Science

Effect of Pressure on Boron Diffusion in Silicon

We are studying the effect of pressure on boron diffusion in silicon in order to better understand the nature of the point defects responsible for diffusion. Si homoepitaxial layers delta-doped with boron were grown using molecular beam epitaxy. Diffusion anneals were performed in a high temperature diamond anvil cell using fluid argon as a pressure medium. Diffusivities were deduced from B concentration-depth profiles measured with using secondary ion mass spectrometry. Preliminary results indicate that pressure enhances B diffusion in Si at 850 ˚C, characterized by an average activation volume of -0.125±0.02 times the atomic volume, and thus appear consistent with an interstitial-based diffusion mechanism. Results are compared with previous hydrostatic-pressure studies, with results in biaxially strained films, and with atomistic calculations of activation volumes for self diffusion.Engineering and Applied Science

Crystal structure of solid Oxygen at high pressure and low temperature

Results of X-ray diffraction experiments on solid oxygen at low temperature and at pressures up to 10 GPa are presented.A careful sample preparation and annealing around 240 K allowed to obtain very good diffraction patterns in the orthorhombic delta-phase. This phase is stable at low temperature, in contrast to some recent data [Y. Akahama et al., Phys. Rev. B64, 054105 (2001)], and transforms with decreasing pressure into a monoclinic phase, which is identified as the low pressure alpha-phase. The discontinuous change of the lattice parameters, and the observed metastability of the alpha-phase increasing pressure suggest that the transition is of the first order.Comment: 4 pages with three figure

Ultra-Efficient and Power Dense Electric Motors for U. S. Industry

The primary purpose of this project was to combine the ease-of-installation and ease-of-use attributes of industrial induction motors with the low-loss and small size and weight advantages of PM motors to create an ultra-efficient, high power density industrial motor that can be started across-the-line or operated from a standard, Volts/Hertz drive without the need for a rotor position feedback device. PM motor products that are currently available are largely variable speed motors that require a special adjustable speed drive with rotor position feedback. The reduced size and weight helps to offset the magnet cost in order make these motors commercially viable. The scope of this project covers horsepower ratings from 20 ? 500. Prototypes were built and tested at ratings ranging from 30 to 250 HP. Since fans, pumps and compressors make up a large portion of industrial motor applications, the motor characteristics are tailored to those applications. Also, since there is extensive use of adjustable frequency inverters in these applications, there is the opportunity to design for an optimal pole number and operate at other than 60 Hz frequency when inverters are utilized. Designs with four and eight pole configurations were prototyped as part of this work. Four pole motors are the most commonly used configuration in induction motors today. The results of the prototype design, fabrication, and testing were quite successful. The 50 HP rating met all of the design goals including efficiency and power density. Tested values of motor losses at 50 HP were 30% lower than energy efficient induction motors and the motor weight is 35% lower than the energy efficient induction motor of the same rating. Further, when tested at the 30 HP rating that is normally built in this 286T frame size, the efficiency far exceeds the project design goals with 30 HP efficiency levels indicating a 55% reduction in loss compared to energy efficient motors with a motor weight that is a few percentage points lower than the energy efficient motor. This 30 HP rating full load efficiency corresponds to a 46% reduction in loss compared to a 30 HP NEMA Premium? efficient motor. The cost goals were to provide a two year or shorter efficiency-based payback of a price premium associated with the magnet cost in these motors. That goal is based on 24/7 operation with a cost of electricity of 10 cents per kW-hr. Similarly, the 250 HP prototype efficiency testing was quite successful. In this case, the efficiency was maximized with a slightly less aggressive reduction in active material. The measured full load efficiency of 97.6% represents in excess of a 50% loss reduction compared to the equivalent NEMA Premium Efficiency induction motor. The active material weight reduction was a respectable 14.5% figure. This larger rating demonstrated both the scalability of this technology and also the ability to flexibly trade off power density and efficiency. In terms of starting performance, the 30 ? 50 HP prototypes were very extensively tested. The demonstrated capability included the ability to successfully start a load with an inertia of 25 times the motor?s own inertia while accelerating against a load torque following a fan profile at the motor?s full nameplate power rating. This capability will provide very wide applicability of this motor technology. The 250 HP prototype was also tested for starting characteristics, though without a coupled inertia and load torque. As a result it was not definitively proven that the same 25 times the motor?s own inertia could be started and synchronized successfully at 250 HP. Finite element modeling implies that this load could be successfully started, but it has not yet been confirmed by a test

Phase stability of transition metals and alloys

This is the final report of a three-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). This project was focused on resolving unexplained differences in calculated and measured phase transition pressures in transition metals. Part of the approach was to do new, higher accuracy calculations of transmission pressures for group 4B and group 6B metals. Theory indicates that the transition pressures for these baseline metals should change if alloyed with a d-electron donor metal, and calculations done using the Local Density Approximation (LDA) and the Virtual Crystal Approximation (VCA) indicate that this is true. Alloy systems were calculated for Ti, Zr and Hf based alloys with various solute concentrations. The second part of the program was to do new Diamond Anvil Cell (DAC) measurements to experimentally verify calculational results. Alloys were prepared for these systems with grain size suitable for Diamond Anvil Cell experiments. Experiments were done on pure Ti as well as Ti-V and Ti-Ta alloys. Measuring unambiguous transition pressures for these systems proved difficult, but a new technique developed yielded good results

Consistent Anisotropic Repulsions for Simple Molecules

We extract atom-atom potentials from the effective spherical potentials that suc cessfully model Hugoniot experiments on molecular fluids, e.g., $O_2$ and $N_2$. In the case of $O_2$ the resulting potentials compare very well with the atom-atom potentials used in studies of solid-state propertie s, while for $N_2$ they are considerably softer at short distances. Ground state (T=0K) and room temperatu re calculations performed with the new $N-N$ potential resolve the previous discrepancy between experimental and theoretical results.Comment: RevTeX, 5 figure

Dynamic model tracking design for low inertia, high speed permanent magnet ac motors

Permanent magnet a

Resource and physiological constraints on global crop production enhancements from atmospheric particulate matter and nitrogen deposition

Changing atmospheric composition, induced primarily by industrialization and climate change, can impact plant health and may have implications for global food security. Atmospheric particulate matter (PM) can enhance crop production through the redistribution of light from sunlight to shaded leaves. Nitrogen transported through the atmosphere can also increase crop production when deposited onto cropland by reducing nutrient limitations in these areas. We employ a crop model (pDSSAT), coupled to input from an atmospheric chemistry model (GEOS-Chem), to estimate the impact of PM and nitrogen deposition on crop production. In particular, the crop model considers the resource and physiological restrictions to enhancements in growth from these atmospheric inputs. We find that the global enhancement in crop production due to PM in 2010 under the most realistic scenario is 2.3, 11.0, and 3.4&thinsp;% for maize, wheat, and rice, respectively. These crop enhancements are smaller than those previously found when resource restrictions were not accounted for. Using the same model setup, we assess the effect of nitrogen deposition on crops and find modest increases ( ∼ &thinsp;2&thinsp;% in global production for all three crops). This study highlights the need for better observations of the impacts of PM on crop growth and the cycling of nitrogen throughout the plant–soil system to reduce uncertainty in these interactions.</p