Flutter of elastically supported orthotropic panels including the effects of flow angle

A theoretical panel flutter analysis and computer program was developed which is capable of analyzing an orthotropic panel with in-plane loads, at various angles of cross flow and various edge-support conditions. The resulting modal analysis uses linear piston-theory aerodynamics and includes both aerodynamic and structural damping. Calculations made for typical panels with no in-plane forces show that large reductions in dynamic presure for flutter are possible with only small changes in flow angle. The reduction in dynamic pressure with flow angle is greater for elastically supported panels than for simply supported panels. Aerodynamic damping has a significant stabilizing effect at all flow angles except zero, whereas structural damping has negligible effect

Effect of preforming adherends on static and fatigue strength of bonded composite single-lap joints

An analytical and experimental investigation was conducted on bonded composite single-lap joints with the adherends performed to reduce the angle between the line of action of the applied in-plane force and the bondline. A classical closed-form solution was used to analyze the composite joints with various preform angles and overlap lengths. The adherends of the test specimens were preformed before bonding, during the layup and curing process. Static tests were conducted for preform angles of 0, 5, 10, and 15 deg and overlap lengths of 0.75, 1.75, 2.75, and 3.75 in. A limited fatigue study was conducted for specimens with a 2.75-in. overlap and a preform angle of 5 deg. Results of the analysis showed that preforming the adherends of bonded composite single-lap joints significantly reduced the shear and peel stress concentrations in the adhesive. Experimental results showed that preforming the adherends significantly increased their static and fatigue strength and thus increased the load level for which bonded composite single-lap joints can be designed

Effects of configuration modifications on aerodynamic characteristics of tension shell shapes at Mach 3.0

Configuration modifications of tension shell shapes to improve aerodynamic characteristics at Mach 3 by delaying onset of flow separatio

Life considerations of the shuttle orbiter densified-tile thermal protection system

The Shuttle orbiter themal protection system (TPS) incorporates ceramic reusable surface insulation tiles bonded to the orbiter substructure through a strain isolation pad. Densification of the bonding surface of the tiles increases the static strength of the tiles. The densification proces does not, however, necessarily lead to an equivalent increase in fatigue strength. Investigation of the expected lifetime of densified tile TPS under both sinusoidal loading and random loading simulating flight conditions indicates that the strain isolation pads are the weakest components of the TPS under fatigue loading. The felt pads loosen under repetitive loading and, in highly loaded regions, could possibly cause excessive step heights between tiles causing burning of the protective insulation between tiles. A method of improving the operational lifetime of the TPS by using a strain isolation pad with increased stiffness is presented as is the consequence of the effect of increased stiffness on the tile inplane strains and transverse stresses

Stability and control characteristics of an air-breathing missile configuration having a forward located inlet

An investigation was made to determine the aerodynamic characteristics of an airbreathing missile configuration having a forward located inlet. Control was provided by cruciform tail surfaces. Aerodynamic data were obtained for the body-tail configuration alone and with planar or cruciform wings. At Mach numbers from 2.86 to 4.63, the model had internal flow. At Mach numbers from 1.70 to 2.86, the internal duct was closed, and an inlet fairing was installed to simulate boost conditions

Fatigue properties of shuttle thermal protection system

Static and cyclic load tests were conducted to determine the static and fatigue strength of the RIS tile/SIP thermal protection system used on the orbiter of the space shuttle. The material systems investigated include the densified and undensified LI-900 tile system on the .40 cm thick SIP and the densified and undensified LI-2200 tile system on the .23 cm (.090 inch) thick SIP. The tests were conducted at room temperature with a fully reversed uniform cyclic loading at 1 Hertz. Cyclic loading causes a relatively large reduction in the stress level that each of the SIP/tile systems can withstand for a small number of cycles. For example, the average static strength of the .40 cm thick SIP/LI-900 tile system is reduced from 86 kPa to 62 kPa for a thousand cycles. Although the .23 cm thick SIP/LI-2200 tile system has a higher static strength, similar reductions in the fatigue strength are noted. Densifying the faying surface of the RSI tile changes the failure mode from the SIP/tile interface to the parent RSI or the SIP and thus greatly increases the static strength of the system. Fatigue failure for the densified tile system, however, occurs due to complete separation or excessive elongation of the SIP and the fatigue strength is only slightly greater than that for the undensified tile system

External store effects on the stability of fighter and interceptor airplanes

Some criteria for external carriage of missiles for fighter aircraft intended for aerial combat missions and for fighter-interceptor missions are considered. The mission requirements discussed include the short-range fighter-interceptor, the short-range interceptor, the medium-range interceptor, and the long-range interceptor. Missiles types considered to be compatible with the various point mission designs include the short-range missile, the medium-range missile, and the long-range missile. From the study, it appears that point mission design aircraft can be arranged in such a way that the required external-store arrangement will not impair the stability of the aircraft. An extensive reference list of NASA external store research is included

Pollutant formation in fuel lean recirculating flows

An opposed reacting jet combustor (ORJ) was tested at a pressure of 1 atmosphere. A premixed propane/air stream was stabilized by a counterflowing jet of the same reactants. The resulting intensely mixed zone of partially reacted combustion products produced stable combustion at equivalence ratios as low as 0.45. Measurements are presented for main stream velocities of 7.74 and 13.6 m/sec with an opposed jet velocity of 96 m/sec, inlet air temperatures from 300 to 600 K, and equivalence ratios from 0.45 to 0.625. Fuel lean premixed combustion was an effective method of achieving low NOx emissions and high combustion efficiencies simultaneously. Under conditions promoting lower flame temperature, NO2 constituted up to 100 percent of the total NOx. At higher temperatures this percentage decreased to a minimum of 50 percent

Simulating Quantum Magnetism with Correlated Non-Neutral Ion Plasmas

By employing forces that depend on the internal electronic state (or spin) of an atomic ion, the Coulomb potential energy of a strongly coupled array of ions can be modified in a spin-dependent way to mimic effective quantum spin Hamiltonians. Both ferromagnetic and antiferromagnetic interactions can be implemented. We use simple models to explain how the effective spin interactions are engineered with trapped-ion crystals. We summarize the type of effective spin interactions that can be readily generated, and discuss an experimental implementation using single-plane ion crystals in a Penning trap.Comment: 10 pages, 5 figures, to be published in the Proceedings of 10th International Workshop on Non-Neutral Plasma