Materials Characterization Using High-Frequency Atomic Force Microscopy and Friction Force Microscopy

During the last decade, Atomic Force Microscopy (AFM) has been widely used to image the topography of various surfaces with corrugations down to the atomic scale [1,2]. Since then, development of new techniques based on AFM has been conducted to evaluate physical, chemical or mechanical surface properties [3]. We describe the use of near-field acoustic microscopy, based on AFM and hereafter referred to as Acoustic Microscopy by Atomic Force Microscopy (AFAM), as it has been developed earlier [4]. The relevance of this new scanning probe microscopy for high-resolution nondestructive testing and evaluation purposes is pointed out. It is shown that AFAM is capable of measuring elasticity on surfaces with a spatial resolution of less than 100 nm. Subsurface elastic properties and subsurface microdefect characterization can be performed by this technique. The high frequency Friction Force Microscopy (FFM) image, hereafter called Acoustic Friction Force Micropscopy (AFFM), reveals information different from the conventionally taken friction force image. We describe experimental and theoretical aspects of high-frequency atomic force and friction force microscopy

Controlling the quality factor of a tuning-fork resonance between 9 K and 300 K for scanning-probe microscopy

We study the dynamic response of a mechanical quartz tuning fork in the temperature range from 9 K to 300 K. Since the quality factor Q of the resonance strongly depends on temperature, we implement a procedure to control the quality factor of the resonance. We show that we are able to dynamically change the quality factor and keep it constant over the whole temperature range. This procedure is suitable for applications in scanning probe microscopy.Comment: 5 pages, 6 figure

Formation, Manipulation, and Elasticity Measurement of a Nanometric Column of Water Molecules

Nanometer-sized columns of condensed water molecules are created by an atomic-resolution force microscope operated in ambient conditions. Unusual stepwise decrease of the force gradient associated with the thin water bridge in the tip-substrate gap is observed during its stretch, exhibiting regularity in step heights (~0.5 N/m) and plateau lengths (~1 nm). Such "quantized" elasticity is indicative of the atomic-scale stick-slip at the tip-water interface. A thermodynamic-instability-induced rupture of the water meniscus (5-nm long and 2.6-nm wide) is also found. This work opens a high-resolution study of the structure and the interface dynamics of a nanometric aqueous column.Comment: 4 pages, 3 figure

Local probing of ionic diffusion by electrochemical strain microscopy: spatial resolution and signal formation mechanisms

Electrochemical insertion-deintercalation reactions are typically associated with significant change of molar volume of the host compound. This strong coupling between ionic currents and strains underpins image formation mechanisms in electrochemical strain microscopy (ESM), and allows exploring the tip-induced electrochemical processes locally. Here we analyze the signal formation mechanism in ESM, and develop the analytical description of operation in frequency and time domains. The ESM spectroscopic modes are compared to classical electrochemical methods including potentiostatic and galvanostatic intermittent titration (PITT and GITT), and electrochemical impedance spectroscopy (EIS). This analysis illustrates the feasibility of spatially resolved studies of Li-ion dynamics on the sub-10 nanometer level using electromechanical detection.Comment: 49 pages, 17 figures, 4 tables, 3 appendices, to be submitted to J. Appl. Phys

P/2010A2 LINEAR - I: An impact in the Asteroid Main Belt

Comet P/2010A2 LINEAR is a good candidate for membership with the Main Belt Comet family. It was observed with several telescopes (ESO NTT, La Silla; Gemini North, Mauna Kea; UH 2.2m, Mauna Kea) from 14 Jan. until 19 Feb. 2010 in order to characterize and monitor it and its very unusual dust tail, which appears almost fully detached from the nucleus; the head of the tail includes two narrow arcs forming a cross. The immediate surroundings of the nucleus were found dust-free, which allowed an estimate of the nucleus radius of 80-90m. A model of the thermal evolution indicates that such a small nucleus could not maintain any ice content for more than a few million years on its current orbit, ruling out ice sublimation dust ejection mechanism. Rotational spin-up and electrostatic dust levitations were also rejected, leaving an impact with a smaller body as the favoured hypothesis, and ruling out the cometary nature of the object. The impact is further supported by the analysis of the tail structure. Finston-Probstein dynamical dust modelling indicates the tail was produced by a single burst of dust emission. More advanced models, independently indicate that this burst populated a hollow cone with a half-opening angle alpha~40degr and with an ejection velocity v_max ~ 0.2m/s, where the small dust grains fill the observed tail, while the arcs are foreshortened sections of the burst cone. The dust grains in the tail are measured to have radii between a=1-20mm, with a differential size distribution proportional to a^(-3.44 +/- 0.08). The dust contained in the tail is estimated to at least 8x10^8kg, which would form a sphere of 40m radius. Analysing these results in the framework of crater physics, we conclude that a gravity-controlled crater would have grown up to ~100m radius, i.e. comparable to the size of the body. The non-disruption of the body suggest this was an oblique impact.Comment: 15 pages, 11 figures, in pres

Nanoscale piezoelectric response across a single antiparallel ferroelectric domain wall

Surprising asymmetry in the local electromechanical response across a single antiparallel ferroelectric domain wall is reported. Piezoelectric force microscopy is used to investigate both the in-plane and out-of- plane electromechanical signals around domain walls in congruent and near-stoichiometric lithium niobate. The observed asymmetry is shown to have a strong correlation to crystal stoichiometry, suggesting defect-domain wall interactions. A defect-dipole model is proposed. Finite element method is used to simulate the electromechanical processes at the wall and reconstruct the images. For the near-stoichiometric composition, good agreement is found in both form and magnitude. Some discrepancy remains between the experimental and modeling widths of the imaged effects across a wall. This is analyzed from the perspective of possible electrostatic contributions to the imaging process, as well as local changes in the material properties in the vicinity of the wall

Abnormal phenomena in a one-dimensional periodic structure containing left-handed materials

The explicit dispersion equation for a one-dimensional periodic structure with alternative layers of left-handed material (LHM) and right-handed material (RHM) is given and analyzed. Some abnormal phenomena such as spurious modes with complex frequencies, discrete modes and photon tunnelling modes are observed in the band structure. The existence of spurious modes with complex frequencies is a common problem in the calculation of the band structure for such a photonic crystal. Physical explanation and significance are given for the discrete modes (with real values of wave number) and photon tunnelling propagation modes (with imaginary wave numbers in a limited region).Comment: 10 pages, 4 figure

Damping of optomechanical disks resonators vibrating in air

We report on miniature GaAs disk optomechanical resonators vibrating in air in the radiofrequency range. The flexural modes of the disks are studied by scanning electron microscopy and optical interferometry, and correctly modeled with the elasticity theory for annular plates. The mechanical damping is systematically measured, and confronted with original analytical models for air damping. Formulas are derived that correctly reproduce both the mechanical modes and the damping behavior, and can serve as design tools for optomechanical applications in fluidic environment

Gravitational Smearing of Minimal Supersymmetric Unification Predictions

A short and mean paper.Comment: 10 pages total + 1 postscript figure (included), revised: all lines are TRULY < 70 characters long (try it!); LBL-32905, UCB-PTH-92/3