High voltage, high current Schottky barrier solar cell

A Schottky barrier solar cell was described, which consists of a layer of wide band gap semiconductor material on which a very thin film of semitransparent metal was deposited to form a Schottky barrier. The layer of the wide band gap semiconductor material is on top of a layer of narrower band gap semiconductor material, to which one of the cell's contacts may be attached directly or through a substrate. The cell's other contact is a grid structure which is deposited on the thin metal film

Schottky barrier solar cell promises improved efficiency

Higher current and higher voltage can be obtained by using Schottky barrier device with wide band-gap semiconductor as top layer and lower band-gap semiconductor underneath. Significant amount of solar radiation that is not absorbed by side band-gap material will be absorbed by narrow band-gap material

Low cost AMOS solar cell development

Recent developments at JPL have demonstrated that high conversion efficiencies are found with GaAs metal semiconductor solar cells when a particular heat treatment processing step is used to introduce an interfacial layer between the metal and the semiconductor. The new cell, called AMOS (Antireflection-Coated Metal-Oxide-Semiconductor), has open circuit voltages of 0.68-0.72 volts and efficiencies of 15% under terrestrial sunlight, as compared to values of 0.45-0.48 volts and 10%, respectively, for similar cells without an interfacial layer. Potentially higher efficiencies are feasible as further improvements are made in optimizing the interfacial layer effect and in increasing the blue response of the cells. A thin film AMOS cell is proposed that uses a thin recrystallized germanium (Ge) layer between a low cost metal substrate and the vapor phase epitaxially (VPE)-grown GaAs

Junction characteristics of silicon solar cells. Part 1: Nonilluminated case

Precise values of the reverse saturation currents in silicon solar cells and magnitudes of the diffusion and recombination components have been obtained. The recombination current as well as leakage current due to shunting are shown to be nonuniform across the cell. The diffusion lengths calculated from the diffusion current components agree well with diffusion lengths measured independently in similar material. Models are given demonstrating the effect of recombination and shunting currents on the dark current-voltage characteristics of solar cells

Photovoltaic conversion of laser energy

The Schottky barrier photovoltaic converter is suggested as an alternative to the p/n junction photovoltaic devices for the conversion of laser energy to electrical energy. The structure, current, output, and voltage output of the Schottky device are summarized. The more advanced concepts of the multilayer Schottky barrier cell and the AMOS solar cell are briefly considered

Preparation of dilute magnetic semiconductor films by metalorganic chemical vapor deposition

A method for preparation of a dilute magnetic semiconductor (DMS) film is provided, in which a Group II metal source, a Group VI metal source and a transition metal magnetic ion source are pyrolyzed in the reactor of a metalorganic chemical vapor deposition (MOCVD) system by contact with a heated substrate. As an example, the preparation of films of Cd(sub 1-x)Mn(sub x)Te, in which 0 is less than or equal to x less than or equal to 0.7, on suitable substrates (e.g., GaAs) is described. As a source of manganese, tricarbonyl (methylcyclopentadienyl) manganese (TCPMn) is employed. To prevent TCPMn condensation during its introduction into the reactor, the gas lines, valves and reactor tubes are heated. A thin-film solar cell of n-i-p structure, in which the i-type layer comprises a DMS, is also described; the i-type layer is suitably prepared by MOCVD

Schottky barrier solar cell

A method of fabricating a Schottky barrier solar cell is described. The cell consists of a thin substrate of low cost material with at least the top surface of the substrate being electrically conductive. A thin layer of heavily doped n-type polycrystalling germanium is deposited on the substrate after a passivation layer is deposited to prevent migration of impurities into the polycrystalline germanium. The polycrystalline germanium is recrystallized to increase the crystal sizes to serve as a base layer on which a thin layer of gallium arsenide is vapor-epitaxilly grown followed by a thermally-grown oxide layer. A metal layer is deposited on the oxide layer and a grid electrode is deposited to be in electrical contact with the top surface of the metal layer

Method of Fabricating Schottky Barrier solar cell

On a thin substrate of low cost material with at least the top surface of the substrate being electrically conductive is deposited a thin layer of heavily doped n-type polycrystalline germanium, with crystalline sizes in the submicron range. A passivation layer may be deposited on the substrate to prevent migration of impurities into the polycrystalline germanium. The polycrystalline germanium is recrystallized to increase the crystal sizes in the germanium layer to not less than 5 micros to serve as a base layer on which a thin layer of gallium arsenide is vapor epitaxially grown to a selected thickness. A thermally-grown oxide layer of a thickness of several tens of angstroms is formed on the gallium arsenide layer. A metal layer, of not more about 100 angstroms thick, is deposited on the oxide layer, and a grid electrode is deposited to be in electrical contact with the top surface of the metal layer. An antireflection coating may be deposited on the exposed top surface of the metal layer

Radiation effects in GaAs AMOS solar cells

The results of radiation damage produced in AMOS (Antireflecting-Metal-Oxide-Semiconductor) cells with Sb2O3 interfacial oxide layers by 1-MeV electrons are presented. The degradation properties of the cells as a function of irradiation fluences were correlated with the changes in their spectral response, C-V, dark forward, and light I-V characteristics. The active n-type GaAs layers were grown by the OM-CVD technique, using sulfur doping in the range between 3 x 10 to the 15th power and 7 x 10 to the 16th power/cu cm. At a fluence of 10 to the 16th power e/sq cm, the low-doped samples showed I sub sc degradation of 8% and V sub oc degradation of 8%. The high-doped samples showed I sub sc and V sub oc degradation of 32% and 1%, respectively, while the fill factor remained relatively unchanged for both. AMOS cells with water vapor-grown interfacial layers showed no significant change in V sub oc

Reactively-sputtered zinc semiconductor films of high conductivity for heterojunction devices

A high conductivity, n-doped semiconductor film is produced from zinc, or Zn and Cd, and group VI elements selected from Se, S and Te in a reactive magnetron sputtering system having a chamber with one or two targets, a substrate holder, means for heating the substrate holder, and an electric field for ionizing gases in the chamber. Zinc or a compound of Zn and Cd is placed in the position of one of the two targets and doping material in the position of the other of the two targets. Zn and Cd may be placed in separate targets while a dopant is placed in the third target. Another possibility is to place an alloy of Zn and dopant, or Zn, Cd and dopant in one target, thus using only one target. A flow of the inert gas is ionized and directed toward said targets, while a flow of a reactant gas consisting of hydrides of the group VI elements is directed toward a substrate on the holder. The targets are biased to attract negatively ionized inert gas. The desired stochiometry for high conductivity is achieved by controlling the temperature of the substrate, and partial pressures of the gases, and the target power and total pressure of the gases in the chamber