2,242 research outputs found
An investigation of PDMS structures for optimized ferroelectret performance
This paper reports the ANSYS simulation and fabrication processes for optimising PDMS ferroelectret performance. The proposed model extends the previously published analytical models and compares this with simulation of individual void geometry. The ferroelectret material is fabricated from PDMS using 3D-printed plastic moulds. The analytical model and Ansys simulation results predict the variation in performance of the PDMS ferroelectret with the different void geometry and surface charge density. The theoretical maximum piezoelectric coefficient d33 achieved was about 220 pC/N. The experimental maximum d33 obtained was 172 pC/N
Electromagnetic vibration energy harvesting using an improved Halbach array
This paper reports an electromagnetic vibration energy harvester using an improved Halbach array. A Halbach array is a specific arrangement of permanent magnets that concentrates the magnetic field on one side of the array while cancelling the field on the other side to almost zero. Previous research showed that although the Halbach array has higher magnetic field density compared to normal magnet layouts, its magnetic flux gradient is not as high. Thus, output powers of energy harvesters with Halbach arrays were found to be less than those with normal magnet layouts. This paper proposes an improved Halbach array that achieves both high magnetic field strength and magnetic flux gradient. Test results showed that the improved Halbach array can increase the output power of energy harvesters by a factor of seven compared to the previous Halbach design and by a factor of 1.5 compared to the normal configuration
Vibration energy harvesting: fabrication, miniaturisation and applications
This paper reviews work at the University of Southampton and its spin-out company Perpetuum towards the use of vibration energy harvesting in real applications. Perpetuum have successfully demonstrated vibration-powered condition monitoring systems for rail and industrial applications. They have pursued applications were volume is not a particular constraint and therefore sufficient power can be harvested. Harvester reliability and longevity is a key requirement and this can be a challenging task in high shock environments. The University of Southampton has investigated the miniaturization of the technology. MEMS electromagnetic harvesters were found to be unsuitable although miniaturized devices fabricated using bulk components did perform well. Screen printed piezoelectric harvesters were also found to perform well and were ideally suited to a low profile application where device thickness was limited. Screen printing was not only used to deposit the active piezoelectric material but also an inertial mass ink based on tungsten. This enables the device to be printed entirely by screen printing providing a low-cost route to manufacture. Finally, details of a simulation tool that can take real world vibrations and estimate vibration energy harvester output was presented. This was used to simulate linear and nonlinear harvesters and in many applications with a characteristic resonant frequency the linear approach was found to be the optimum. Bistable nonlinear harvesters were found to work better with more random vibration source
Improving the dielectric and piezoelectric properties of screen-printed low temperature PZT/polymer composite using cold isostatic pressing
This paper reports an improvement in dielectric and piezoelectric properties of screen-printed PZT/polymer films for flexible electronics applications using Cold Isostatic Pressing (CIP). The investigation involved half and fully cured PZT/polymer composite pastes with weight ratio of 12:1 to investigate the effect of the CIP process on the piezoelectric and dielectric properties. It was observed that the highest dielectric and piezoelectric properties are achieved at pressures of 5 and 10 MPa for half and fully cured films respectively. The relative dielectric constants were 300 and 245 measured at 1 kHz for the half and fully cured samples. Using unoptimised poling conditions, the initial d33 values were 30 and 35 pC/N for the half and fully cured films, respectively. The fully cured sample was then poled using optimized conditions and demonstrated a d33 of approximately 44 pC/N which is an increase of 7% compared with non-CIP processed material
Probabilistic framework for multiaxial LCF assessment under material variability
The influence of material variability upon the multiaxial LCF assessment of engineering components is missing for a comprehensive description. In this paper, a probabilistic framework is established for multiaxial LCF assessment of notched components by using the Chaboche plasticity model and Fatemi-Socie criterion. Simulations from experimental results of two steels reveal that the scatter in fatigue lives can be well described by quantifying the variability of four material parameters Ï\u83fâ\u80²,εfâ\u80²,b,c. A procedure for choosing the safety factor for fatigue design has been derived by using first order approximation
Development of a low temperature PZT/polymer paste for screen printed flexible electronics applications
Some recent developments in quantization of fractal measures
We give an overview on the quantization problem for fractal measures,
including some related results and methods which have been developed in the
last decades. Based on the work of Graf and Luschgy, we propose a three-step
procedure to estimate the quantization errors. We survey some recent progress,
which makes use of this procedure, including the quantization for self-affine
measures, Markov-type measures on graph-directed fractals, and product measures
on multiscale Moran sets. Several open problems are mentioned.Comment: 13 page
Trajectories of fatigue in cancer patients during psychological care
Objective Psycho-oncological institutions offer specialized care for cancer patients. Little is known how this care might impact fatigue. This study aimed to identify fatigue trajectories during psychological care, examined factors distinguishing these trajectories and predicted fatigue severity after nine months of psychological care. Design Naturalistic, longitudinal study of 238 cancer patients receiving psycho-oncological care in the Netherlands. Data were collected before initiation of psychological care (T1) and three (T2) and nine months (T3) afterwards. Latent class growth analysis, repeated measure analyses (RMA) and linear regression analysis were performed. Main Outcome Measures Fatigue severity: Checklist Individual Strength. Results Three fatigue trajectories were identified: high- (30%), moderate- (62%) and low-level fatigue (8%). While statistically significant decreases in fatigue were found, this decrease was not clinically relevant. RMA showed main effects for time for fatigue trajectories on depression, anxiety, personal control and illness cognitions. Fatigue severity and physical symptoms at T1, but not demographic or clinical factors, were predictive of fatigue severity at T3. Conclusions Fatigue is very common during psycho-oncological care, and notably not clinically improving. As symptoms of fatigue, depression, anxiety and physical symptoms often cluster, supplementary fatigue treatment should be considered when it is decided to treat other symptoms first
- …