323 research outputs found

    Influence of projectile shape on dynamic behavior of steel sheet subjected to impact and perforation

    Get PDF
    Authors thank Ministry of Science and Higher Education of Poland for financial support under Grants: R00 0097 12. Authors thank also M. Tavian technician in electronics from ENIM for his contribution on the development of the residual velocity measurement sensors.The paper describes a work focused on the process of perforation of steel sheet.Experimental,analytical and numerical investigations have been carried out to analyze in details the perforation process.Based on these approaches,the ballistic properties of the material and the failure modes depending on the projectile nose shape(conical,blunt or hemispherical) have been studied.Different failure modes have been observed,including petaling, plug ejection and circumference necking.The special study about the number of petals has been done for different nose angles using conical shape projectiles.The complete energy balance is also reported and the absorbed energy by the steel sheet has been obtained by measuring initial and residual projectile velocities.A wide range of impact velocities from 35to180m/s has been covered during the tests.All the projectiles are 13mm in diameter and the plates are1mm thick.Moreover,the mass ratio(projectile mass/steel sheet mass) and the ratio between the span of the steel sheet and the diameter of the projectile are constant, equal to 0.38 and 3.85, respectively

    Material and structural behaviour of PMMA from low temperatures to over the glass transition: Quasi-static and dynamic loading

    Get PDF
    This work aims at characterizing the mechanical behaviour of polymethyl-methacrylate (PMMA) under high velocity impact conditions over a wide range of testing temperatures. To this end, the mechanical response at uniaxial compression is studied for both quasi-static and dynamic conditions covering testing temperatures below, at and above glass transition. A pseudo-brittle to ductile transition in the failure of PMMA is observed at a threshold that depends on testing temperature and strain rate. This analysis allows for the interpretation of the perforation impact tests and to explain the principal deformation and failure mechanisms. To complete the study, the Richeton model to predict yielding is revisited. Finally, we provide a new constitutive model for finite deformations to further identify the deformation mechanisms governing the mechanical behaviour of PMMA and the influence of temperature and strain rate on them.D. Garcia-Gonzalez acknowledges support from the Talent Attraction grant (CM 2018 - 2018-T2/IND-9992) from the Comunidad de Madrid

    Perforation Analysis of the Aluminum Alloy Sheets Subjected to High Rate of Loading and Heated Using Thermal Chamber: Experimental and Numerical Approach

    Get PDF
    The analysis of the mechanical characteristics and dynamic behavior of aluminum alloy sheet due to perforation tests based on the experimental tests coupled with the numerical simulation is presented. The impact problems (penetration and perforation) of the metallic plates have been of interest for a long time. Experimental, analytical as well as numerical studies have been carried out to analyze in details the perforation process. Based on these approaches, the ballistic properties of the material have been studied. The initial and residual velocities laser sensor is used during experiments to obtain the ballistic curve and the ballistic limit. The energy balance is also reported together with the energy absorbed by the aluminum including the ballistic curve and ballistic limit. The high speed camera helps to estimate the failure time and to calculate the impact force. A wide range of initial impact velocities from 40 up to 180 m/s has been covered during the tests. The mass of the conical nose shaped projectile is 28 g, its diameter is 12 mm, and the thickness of the aluminum sheet is equal to 1.0 mm. The ABAQUS/Explicit finite element code has been used to simulate the perforation processes. The comparison of the ballistic curve was obtained numerically and was verified experimentally, and the failure patterns are presented using the optimal mesh densities which provide the stability of the results. A good agreement of the numerical and experimental results is observed

    An experimental method of measuring the quasi-static and dynamic confined behaviour of PMMA

    Full text link
    A testing device is presented for the experimental study of the confined behaviour of PMMA in compression under quasi-static loading or at high strain-rates. The constitutive relation of the material ring (allowing to confine the PMMA) being known, transverse gauges glued on its lateral surface allow for the measurement of the lateral confining pressure. The hydrostatic pressure and the Mises stress may be computed. Quasi-static and dynamic tests performed in a strain-rate range of 1e-3/s 1e3/s are processed with the method and compared to results of unconfined compression tests. It is found that the compressive behaviour of PMMA is weakly influenced by the level of pressure and much more sensitive to strain-rate: an elastic brittle behaviour is observed at high strain-rates in unconfined or confined conditions whereas elastoplastic behaviour is noted under quasi-static loading

    Ballistic behavior of steel sheet subjected to impact and perforation

    Get PDF
    The paper is reporting some comparisons between experimental and numerical results in terms of failure mode, failure time and ballistic properties of mild steel sheet. Several projectile shapes have been considered to take into account the stress triaxiality effect on the failure mode during impact, penetration and perforation. The initial and residual velocities as well as the failure time have been measured during the tests to estimate more physical quantities. It has to be noticed that the failure time was defined using a High Speed Camera (HSC). Thanks to it, the impact forces (average and maximum level), were analyzed using numerical simulations together with an analytical description coupled to experimental observations. The key point of the model is the consideration of a shape function to define the pulse loading during perforation

    Symmetry Representations in the Rigged Hilbert Space Formulation of Quantum Mechanics

    Get PDF
    We discuss some basic properties of Lie group representations in rigged Hilbert spaces. In particular, we show that a differentiable representation in a rigged Hilbert space may be obtained as the projective limit of a family of continuous representations in a nested scale of Hilbert spaces. We also construct a couple of examples illustrative of the key features of group representations in rigged Hilbert spaces. Finally, we establish a simple criterion for the integrability of an operator Lie algebra in a rigged Hilbert space

    Microstructure Effects on the Machinability of AM-Produced Superalloys

    Get PDF
    This paper discusses the microstructure effects on the machinability of Inconel 718 by conducting machining tests on an additively manufactured (AM) workpiece with a strongly textured grain structure and a wrought workpiece incorporating a finer and more equiaxed grain structure. The AM workpiece was produced as a thin tube using Laser Melting Powder Bed Fusion and optimal processing conditions for this alloy. A lathe was used to conduct instrumented orthogonal machining tests on the two workpiece materials under dry cut and coolant conditions using a semisynthetic emulsion coolant. The process parameters studied were feed from 0.05 to 0.15 mm/rev and cutting speed from 60 to 120 m/min with a cut time of 2 sec duration for each process condition. Measures for each process condition included cutting forces in the feed and main cut direction, and images of chip forms were obtained. The grain structures of the workpiece materials were characterized using Electron Back Scattered Diffraction (EBSD). New findings suggest that grain structures can significantly affect the machinability of the superalloy at a higher feed for all cutting speeds studied, and insights into the cause are discussed. Other important findings comment on the effectiveness of the coolant as a lubricant for reducing friction in machining
    corecore