Synthesis of Allylamine Plasma Polymer Films: Correlation between Plasma Diagnostic and Film Characteristics

peer reviewedPrimary amine-based plasma polymer films (NH2-PPF) were synthesized using plasma polymerization of allylamine in continuous wave (CW) and pulsed radio-frequency (RF) modes. Plasma chemistry, studied by residual gas analysis mass spectrometry, revealed that the precursor fragmentation is a function of the equivalent power (Peq) dissipated in the discharge, independently of the plasma mode used. X-ray photoelectron spectroscopy combined with time-of-flight secondary ion mass spectrometry suggests as the precursor fragmentation in the plasma increases: (i) a decrease of the primary amine concentration in the NH2-PPF (%NH2) and (ii) an increase of the cross-linking degree. For a given Peq, similar to the precursor fragmentation in the plasma, the NH2-PPF characteristics were found to be independent of the plasma mode used. Therefore, the main advantage of using pulsed RF processes over CW ones is the possibility to work at very low Peq which enables low precursor fragmentation, optimization of %NH2, and reduction of the film cross-linking degree. The chemical composition and the cross-linking degree of the NH2-PPF synthesized by allylamine plasma polymerization can thus be tailored by adjusting the equivalent RF power injected in the plasma

Plasma polymerization of ethyl lactate

Plasma polymerization of ethyl lactate precurso

Plasma polymerization of ethyl lactate

Plasma polymerization of ethyl lactat

Synthesis of superhydrophobic PTFE-like thin films by self- nanostructuration in a hybrid plasma process

Superhydrophobic poly(tetrafluoro-ethylene) (PTFE) like thin films were grown on silicon wafers using a plasma-based hybrid process consisting on sputtering a carbon target in an Ar/CF 4 atmosphere. The influence of the bias voltage applied to the substrate (V Bias) as well as of the gas mixture composition (%CF 4) on the chemical composition, the wettability and the morphology of the deposited thin films were evaluated. The chemical composition measured by X-ray Photoelectron Spectroscopy (XPS) has revealed that the F/C atomic ratio is always lower than for conventional PTFE (F/C = 2) and that it decreases when V Bias increases (from F/C = 1 for V Bias = - 100 V to F/C = 0.75 for V Bias = - 200 V). This behavior is associated with the preferential sputtering of the fluorine atoms during the plasma-assisted growth of the films. Consecutively, a self-nanostructuration enhanced when increasing V Bias is observed. As a consequence, the water contact angle (WCA) measurements range from 70° up to 150° depending on (i) the fluorine concentration and (ii) on the magnitude of the nanostructuration. In addition, for the films presenting the highest WCAs, a small hysteresis between the advancing and receding WCAs is observed (< 10°) allowing these films to fulfill completely the requirements of superhydrophobicity. The nanostructuration is probably due to the chemical etching by fluorine atoms of the fluorinated group. In order to get more understanding on the wettability mechanisms of these surfaces, the topography of the films has been evaluated by atomic force microscopy (AFM). The data have revealed, for all films, a dense and regular structure composed by conic objects (A vH is their average height and A vD is the average distance between them) for which the dimensions increase with V Bias. A correlation between A vH/A vD, defined as the morphological ratio, with the WCA was established. Theoretical evaluations of the WCA using the Wenzel and Cassie equations with, as inputs, the features of the deposited thin film surfaces measured by AFM suggest that the wetting regime is intermediate between these two ideal situations. © 2012 Elsevier B.V. All rights reserved.SCOPUS: ar.jinfo:eu-repo/semantics/publishe

Antibacterial inorganic coatings on metallic surfaces for temporary fixation devices

Bacterial contamination and bone tissue overgrowth are currently the main issues for temporary fixation devices. The aim of this research is the development of innovative inorganic coatings able to reduce bacterial adhesion and bone tissue overgrowth without hampering cytocompatibility. 316L stainless-steel, Titanium grade4 and Titanium grade5 were selected as substrates, as currently used in temporary fixation devices. Starting from previous results on silica, alumina and zirconia were selected as coating matrices, according to their higher chemical stability, reduced bacterial adhesion and possible reduction of tissue overgrowth. Coatings were produced by co-sputtering. Coating adhesion was evaluated by tape test. Samples were immersed in ultrapure water up to 28 days to investigate silver release and chemical stability in fluids. Surface roughness was measured by contact profilometry. Surface wettability was determined by contact angle measurements and antibacterial activity was studied against antibiotic resistant S aureus. The research demonstrates the possibility to obtain coatings with roughness lower than the critical threshold for the increase of bacterial adhesion (0.2 mu m) and optimal mechanical adhesion to metallic substrates. Coating chemical stability in water is strongly affected by the coating matrix composition. Silver release can be tailored to obtain antibacterial and biocompatible surfaces

Global economic burden of unmet surgical need for appendicitis

Background There is a substantial gap in provision of adequate surgical care in many low- and middle-income countries. This study aimed to identify the economic burden of unmet surgical need for the common condition of appendicitis. Methods Data on the incidence of appendicitis from 170 countries and two different approaches were used to estimate numbers of patients who do not receive surgery: as a fixed proportion of the total unmet surgical need per country (approach 1); and based on country income status (approach 2). Indirect costs with current levels of access and local quality, and those if quality were at the standards of high-income countries, were estimated. A human capital approach was applied, focusing on the economic burden resulting from premature death and absenteeism. Results Excess mortality was 4185 per 100 000 cases of appendicitis using approach 1 and 3448 per 100 000 using approach 2. The economic burden of continuing current levels of access and local quality was US $92 492 million using approach 1 and$73 141 million using approach 2. The economic burden of not providing surgical care to the standards of high-income countries was $95 004 million using approach 1 and$75 666 million using approach 2. The largest share of these costs resulted from premature death (97.7 per cent) and lack of access (97.0 per cent) in contrast to lack of quality. Conclusion For a comparatively non-complex emergency condition such as appendicitis, increasing access to care should be prioritized. Although improving quality of care should not be neglected, increasing provision of care at current standards could reduce societal costs substantially

Global economic burden of unmet surgical need for appendicitis

Background There is a substantial gap in provision of adequate surgical care in many low- and middle-income countries. This study aimed to identify the economic burden of unmet surgical need for the common condition of appendicitis. Methods Data on the incidence of appendicitis from 170 countries and two different approaches were used to estimate numbers of patients who do not receive surgery: as a fixed proportion of the total unmet surgical need per country (approach 1); and based on country income status (approach 2). Indirect costs with current levels of access and local quality, and those if quality were at the standards of high-income countries, were estimated. A human capital approach was applied, focusing on the economic burden resulting from premature death and absenteeism. Results Excess mortality was 4185 per 100 000 cases of appendicitis using approach 1 and 3448 per 100 000 using approach 2. The economic burden of continuing current levels of access and local quality was US $92 492 million using approach 1 and$73 141 million using approach 2. The economic burden of not providing surgical care to the standards of high-income countries was $95 004 million using approach 1 and$75 666 million using approach 2. The largest share of these costs resulted from premature death (97.7 per cent) and lack of access (97.0 per cent) in contrast to lack of quality. Conclusion For a comparatively non-complex emergency condition such as appendicitis, increasing access to care should be prioritized. Although improving quality of care should not be neglected, increasing provision of care at current standards could reduce societal costs substantially