Study on QoS support in 802.11e-based multi-hop vehicular wireless ad hoc networks

Multimedia communications over vehicular ad hoc networks (VANET) will play an important role in the future intelligent transport system (ITS). QoS support for VANET therefore becomes an essential problem. In this paper, we first study the QoS performance in multi-hop VANET by using the standard IEEE 802.11e EDCA MAC and our proposed triple-constraint QoS routing protocol, Delay-Reliability-Hop (DeReHQ). In particular, we evaluate the DeReHQ protocol together with EDCA in highway and urban areas. Simulation results show that end-to-end delay performance can sometimes be achieved when both 802.11e EDCA and DeReHQ extended AODV are used. However, further studies on cross-layer optimization for QoS support in multi-hop environment are required

On the predominant mechanisms active during the high power diode laser modification of the wettability characteristics of an SiO2/Al2O3-based ceramic material

The mechanisms responsible for modifications to the wettability characteristics of a SiO2/Al2O3-based ceramic material in terms of a test liquid set comprising of human blood, human blood plasma, glycerol and 4-octonol after high power diode laser (HPDL) treatment have been elucidated. Changes in the contact angle, , and hence the wettability characteristics of the SiO2/Al2O3-based ceramic were attributed primarily to: modifications to the surface roughness of the ceramic resulting from HPDL interaction which accordingly effected reductions in ; the increase in the surface O2 content of the ceramic after HPDL treatment; since an increase in surface O2 content intrinsically brings about a decrease in , and vice versa and the increase in the polar component of the surface energy, due to the HPDL induced surface melting and resolidification which consequently created a partially vitrified microstructure that was seen to augment the wetting action. However, the degree of influence exerted by each mechanism was found to differ markedly. Isolation of each of these mechanisms permitted the magnitude of their influence to be qualitatively determined. Surface energy, by way of microstructural changes, was found to be by far the most predominant element governing the wetting characteristics of the SiO2/Al2O3-based ceramic. To a much lesser extent, surface O2 content, by way of process gas, was also seen to influence to a changes in the wettability characteristics of the SiO2/Al2O3-based ceramic, whilst surface roughness was found to play a minor role in inducing changes in the wettability characteristics

Wetting and bonding characteristics of selected liquid-metals with a high power diode laser treated alumina bioceramic

Changes in the wettability characteristics of an alumina bioceramic occasioned by high power diode laser (HPDL) surface treatment were apparent from the observed reduction in the contact angle. Such changes were due to the HPDL bringing about reductions the surface roughness, increases in the surface O2 content and increases in the polar component of the surface energy. Additionally, HPDL treatment of the alumina bioceramic surface was found to effect an improvement in the bonding characteristics by increasing the work of adhesion. An electronic approach was used to elucidate the bonding characteristics of the alumina bioceramic before and after HPDL treatment. It is postulated that HPDL induced changes to the alumina bioceramic produced a surface with a reduced bandgap energy which consequently increased the work of adhesion by increasing the electron transfer at the metal/oxide interface and thus the metal-oxide interactions. Furthermore, it is suggested that the increase in the work of adhesion of the alumina bioceramic after HPDL treatment was due to a correlation existing between the wettability and ionicity of the alumina bioceramic; for it is believed that the HPDL treated surface is less ionic in nature than the untreated surface and therefore exhibits better wettability characteristics

3D printing-directed auxetic Kevlar aerogel architectures with multi-functionalizable properties

Auxetic architectures with a negative Poisson’s ratio have attracted increasing attention due to their intriguing physical properties, numerous promising applications and recent advancements in manufacturing techniques. However, fabrication of three-dimensional (3D) polymeric auxetic architectures with tailored hierarchically porous structure and desired physical/mechanical properties remains challenging. Herein, 3D nanofibrous Kevlar aerogel architectures with porosity at multi-scales have been designed and fabricated through a new additive manufacturing strategy, i.e., integration of direct ink writing and freeze-casting with non-toxic solvent-based inks following special drying techniques. The highly porous 3D nanofibrous Kevlar aerogel architectures achieve excellent mechanical properties with ultralow density (down to 11.9 mg·cm-3) and large specific surface area (up to 350 m2·g-1). The Poisson’s ratio is tunable in a wide range, spanning from −0.8 to 0.4, by adjusting the spatial arrangement of the struts in geometries. Finally, these nanofibrous Kevlar aerogel architectures have been further functionalized into hydrophobic, luminescent and thermal-responsive architectures by using fluorocarbon resin, functional dyes and organic phase-change materials respectively. The multi-functionalizable auxetic aerogel architectures demonstrate potentials for a broad range of applications