Dynamics of particle loading in deep-bed filter. Transport, deposition and reentrainment

Deep bed filtration is an effective method of submicron and micron particle removal from the fluid stream. There is an extensive body of literature regarding particle deposition in filters, often using the classical continuum approach. However, the approach is not convenient for studying the influence of particle deposition on filter performance (filtration efficiency, pressure drop) when non-steady state boundary conditions have to be introduced. For the purposes of this work the lattice-Boltzmann model describes fluid dynamics, while the solid particle motion is modeled by the Brownian dynamics. For aggregates the effect of their structure on displacement is taken into account. The possibility of particles rebound from the surface of collector or reentrainment of deposits to fluid stream is calculated by energy balanced oscillatory model derived from adhesion theory. The results show the evolution of filtration efficiency and pressure drop of filters with different internal structure described by the size of pores. The size of resuspended aggregates and volume distribution of deposits in filter were also analyzed. The model enables prediction of dynamic filter behavior. It can be a very useful tool for designing filter structures which optimize maximum lifetime with the acceptable values of filtration efficiency and pressure drop

Numerical simulation of deformation and fragmentation of fractal-like nanoaggregates

Aflexible fractal-like aggregate modelwas used to study deformation and fragmentation of the structure of fractal-like aggregates via their impaction with rigid rough surface.Aggregateswere conveyed one at the time towards a surface under vacuum conditions. The number of primary particles remaining in each fragment, ratio of average fragment radius of gyration after impaction to the average fragment initial radius of gyration and ratio of average coordination number to the initial coordination number were monitored for each individual aggregate. Results demonstrate that depending on the impact velocity, the fractal dimension of the aggregate, the strength of bonds between primary particles, the stiffness of the aggregate structure and the diameter of primary particle composing an aggregate, restructuring or breakage of the aggregate occur. Moreover, in the analysis of the ratio of coordination number of aggregates after impaction to the initial coordination number, three regimes were distinguished: first no deformation at low impact velocities, second restructurisation regime and finally fragmentation regime where partial or total fragmentation of aggregates was observed

The effect of selected nanoparticles on rheological properties of human blood

The aim of the study was to determine the influence of selected nanoparticles, namely diesel exhaust particles, Arizona test dust, silver and gold on the rheology of human blood. The rheological properties of human blood were determined with the use of a modular rheometer, at two various temperatures, namely 36.6°C and 40°C. Experimental results were used to calculate the constants in blood constitutive equations. The considered models were power-law, Casson and Cross ones. The obtained results demonstrate that the presence of different nanoparticles in the blood may have different effect on its apparent viscosity depending on the type of particles and shear rate

Fibrous Structures Produced Using the Solution Blow-Spinning Technique for Advanced Air Filtration Process

This study proposes utilising the solution blow-spinning process (SBS) for manufacturing a biodegradable filtration structure that ensures high efficiency of particle filtration with an acceptable pressure drop. The concept of multi-layer filters was applied during the design of filters. Polylactic acid (PLA) was used to produce various layers, which may be mixed in different sequences, building structures with varying filtration properties. Changing the process parameters, one can create layers with diverse average fibre diameters and thicknesses. It enables the design and creation of optimal filtration materials prepared for aerosol particle filtration. The structures were numerically modelled using the lattice Boltzmann approach to obtain detailed production guidelines using the blow-spinning technique. The advantage of this method is the ability to blow fibres with diameters in the nanoscale, applying relatively simple and cost-effective equipment. For tested PLA solutions, i.e., 6% and 10%, the mean fibre diameter decreases as the concentration decreases. Therefore, the overall filtering efficiency decreases as the concentration of the used solution increases. The produced multi-layer filters have 96% overall filtration efficiency for particles ranging from 0.26 to 16.60 micrometres with a pressure drop of less than 160 Pa. Obtained results are auspicious and are a step in producing efficient, biodegradable air filters

Hybrid Modification of Unsaturated Polyester Resins to Obtain Hydro- and Icephobic Properties

Ice accumulation is a key and unsolved problem for many composite structures with polymer matrices, e.g., wind turbines and airplanes. One of the solutions to avoid icing is to use anti-icing coatings. In recent years, the influence of hydrophobicity of a surface on its icephobic properties has been studied. This solution is based on the idea that a material with poor wettability maximally reduces the contact time between a cooled drop of water and the surface, consequently prevents the formation of ice, and decreases its adhesion to the surface. In this work, a hybrid modification of a gelcoat based on unsaturated polyester resin with nanosilica and chemical modifiers from the group of triple functionalized polyhedral oligomeric silsesquioxanes (POSS) and double organofunctionalized polysiloxanes (generally called multi-functionalized organosilicon compounds (MFSC)) was applied. The work describes how the change of modifier concentration and its structural structure finally influences the ice phobic properties. The modifiers used in their structure groups lowered the free surface energy and crosslinking groups with the applied resin, lowering the phenomena of migration and removing the modifier from the surface layer of gelcoat. The main studies from the icephobicity point of view were the measurements of ice adhesion forces between modified materials and ice. The tests were based on the measurements of the shear strength between the ice layer and the modified surface and were conducted using a tensile machine. Hydrophobic properties of the obtained nanocomposites were determined by measurement of the contact angle and contact angle hysteresis. As the results of the work, it was found that the modification of gelcoat with nanosilica and multi-functionalized silicone compounds results in the improvement of icephobic properties when compared to unmodified gelcoat while no direct influence of wettability properties was found. Ice adhesion decreased by more than 30%

Silsesquioxane-Doped Electrospun Nanofibrillar Membranes for Separation Systems

In this study, a series of cage siloxanes (CS), e.g., three polyhedral oligomeric silsesquioxanes (SSQs) and one spherosilicate (SS) derivative, were applied as functional additives for the preparation of poly(lactic acid)-based (PLA) nanofibrillar membranes with an electrospinning technique utilizing an efficient spinning wire electrode setup. The impact of the additives’ structure, chemistry, and electrospinning parameters on the obtained materials’ morphology (scanning electron microscopy) and physicochemical (thermogravimetry, differential scanning calorimetry, contact angle analysis, air flow analysis) properties is discussed. It is presented that applying organosilicon additives may extend the already tuneable properties of the membranes produced by electrospinning performed under different conditions and that they enable to obtain nanofibres of smaller diameter, which in turn increases the membrane porosity. Furthermore, the solvent-assisted electrospinning method allowed for unparalleled mixing of the PLA matrix with the CS additives, as no traces of free additives were visible on the membranes by scanning electron microscopy (SEM) imaging. The resulting membranes can be utilized as filter materials

Hydrophobic and Anti-Icing Behavior of UV-Laser-Treated Polyester Resin-Based Gelcoats

Ice accumulation on wind turbine blades due to the impact of supercooled water droplets can be reduced by the application of surfaces with anti-icing properties. Hydrophobic surfaces are considered as a promising solution because of their water repellent behavior. In recent years, short-pulsed laser technologies have been developed as an efficient technique to modify the surface properties of materials. However, the anti-icing properties of such surfaces have not yet been validated. In this work, a hybrid modification of polyester resin-based gelcoats was adopted. Laser patterning (LP) was used to produce periodic surface structures on modified unsaturated polyester resin (UPR) substrates. One of the innovations of this research is the utilization of novel purpose-made chemical modifiers for gelcoats. The implementation of linear polymethylhydrosiloxane (PMHS) as a building block is a key improvement in terms of durability and functionality of the coating, since there is an option of introducing not only groups bonding in the polyester into one molecule, but also groups that increase hydrophobicity. The other novelty is a successfully conducted experiment combining such chemical modification with laser texturization of the surface. The influence of the laser energy, pattern shape, and spatial periods on the topographical characteristics and hydrophobicity as well as the anti-icing properties of the produced surfaces were investigated. To characterize the surface topography of the produced structures, scanning electron microscopy (SEM) and profilometer were utilized. Measurements of the wettability parameters (static contact angle and contact angle hysteresis) on the treated surfaces allowed the identification of the influence of wetting behavior and laser parameters on the investigated materials. Anti-icing properties were characterized by ice adhesion (IA) and freezing delay time (FDT) tests. It was found that hybrid modification of unsaturated polyester resin by chemical modifiers and laser treatment increased the hydrophobic and anti-icing properties of polyester gelcoats.This research was funded by National Centre for Research and Development (NCBiR), grant number LIDER/16/0068/L-9/17/NCBR/2018.Peer reviewe

Hydro- and Icephobic Properties and Durability of Epoxy Gelcoat Modified with Double-Functionalized Polysiloxanes

Anti-icing coatings have provided a very good alternative to current, uneconomic, active deicing methods, and their use would bring a number of significant benefits to many industries, such as aviation and energy. Some of the most promising icephobic surfaces are those with hydrophobic properties. However, the relationship between hydrophobicity and low ice adhesion is not yet clearly defined. In this work, chemical modification of an epoxy gelcoat with chemical modifiers from the group of double organofunctionalized polysiloxanes (generally called multifunctionalized organosilicon compounds (MFSCs)) was applied. The anti-icing properties of manufactured coatings were determined by means of measurements of shear strength between the ice layer and the modified surface, conducted using a tensile machine. In the work, tests were also performed on the roughness, wettability, and durability of the properties in an aging chamber. It was found that the performed modifications of the coating’s chemical composition by the addition of polysiloxanes enabled us to reduce ice adhesion by 51% and to increase the water contact angle by 14% in comparison to the neat gelcoat. A reduction in ice adhesion was also observed with the increasing water contact angle and with decreasing surface roughness. In addition, only one modification recorded an increase in ice adhesion after exposure in the aging chamber

Biocomposites Based on Polyamide 11/Diatoms with Different Sized Frustules

Amorphous diatomite was used as a filler for a thermoplastic polymer of polyamide 11 obtained from natural sources. The diatomite particles of different sizes were previously fractionated by sedimentation to obtain powders with varying particle size distribution, including powders with or without frustule particles, crushed, uncrushed or agglomerated. Biocomposites containing 2.5, 5, 10 and 20% filler were tested for their mechanical properties, including tensile strength, flexural strength and impact strength. In addition, a particle size analysis (by Dynamic Light Scattering, DLS) was performed and the dispersion of the filler in the polymer matrix (Scanning Electron Microscopy, SEM), thermal parameters (Differential Scanning Calorimetry, DSC, and Dynamic Mechanical Analysis, DMA) were determined. Testing showed that biocomposites modified with diatomaceous earth have a higher mechanical strength than the reference system, especially with larger amounts of the filler (10 and 20%), e.g., the tensile strength of pure PA11 is about 46 MPa, while 20OB and 20OF 47.5 and 47 MPa, respectively, while an increase in max. flexural strength and flexural modulus is also observed compared to pure PA11 by a maximum of 63 and 54%, respectively Diatomaceous earth can be obtained in various ways—it is commercially available or it is possible to breed diatoms in laboratory conditions, while the use of commercially available diatomite, which contains diatoms of different sizes, eliminates the possibility of controlling mechanical parameters by filling biocomposites with a filler with the desired particle size distribution, and diatom breeding is not possible on an industrial scale. Our proposed biocomposite based on fractionated diatomaceous earth using a sedimentation process addresses the current need to produce biocomposite materials from natural sources, and moreover, the nature of the process, due to its simplicity, can be successfully used on an industrial scale